Sani-Lav 56FBL Manual


Læs gratis den danske manual til Sani-Lav 56FBL (10 sider) i kategorien Køkkenvask. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Sani-Lav 56FBL, eller vil du spørge andre brugere om produktet?

Side 1/10
1
A C O R B AT T E R Y P O W E R E D
W A S H S TAT I O N W I T H E L E C T R O N I C S E N S O R
Operating Manual for -Person Hands-Free Floor Mount 3
Stainless Steel Wash Station
AC Models 56FAL and 56FAL-0.5
Battery Models 56FBL and 56FBL-0.5
of Domestic and Foreign Parts
Columbia does not recommend use with harsh chemicals.
NSF/ANSI 2 Food Equipment, NSF/ANSI 372 Lead-Free Compliant, ASME A112.18.1
2
COLUMBIA SPECIFICATIONS
A C O R B AT T E R Y P O W E R E D
800.626.2117 columbiasinks.com info@columbiasinks.com
©2021 Columbia Products
W A S H S TAT I O N W I T H E L E C T R O N I C S E N S O R
Parts List
(1) Floor mount wash station
(1) Leg assembly set
(6) Nuts, bolts and washers for leg assembly
(4) Nuts and washers for connecting sink to leg assembly
(3) AC or Battery powered sensor faucet assembly
(3) Mixing check valve
(1) Strainer assembly with basket
Installation Instructions
Step 1
1. 2 and 3-Person models require leg assembly.
2. Place wash station sink on leg assembly and secure with hardware (provided).
3. Establish sink location.
4. Mark the floor where the four holes are at the base as shown in illustration A.
5. Drill holes as required for mounting hardware. (Hardware not included).
Step 2
1. Install strainer assembly.
2. Install faucets to the sink following the instructions provided with sensor unit.
3. Attach supply tube with elbow to back of faucet.
4. Install mixing check valve and compression fitting to control box of each sensor faucet.
Step 3
1. Secure wash station to floor.
2. Connect waste line to strainer assembly (s).
3. Mount sensor control boxes at desired location on wall.
4. Connect power line from sensor to control box.
5. Attach supply tube from faucet to control box.
6. Connect hot and cold water from the source to mixing check valve (s).
7. Remove aerator from the spout assemblies and flush water system. (see step 7 sensor
installation instructions)
8. Check connections for leaks.
9. Replace aerator onto the spout (s).
Step 4
1. Seal gap between bowl and leg assembly as shown in illustration B.
2. We recommend sealing top of backsplash to wall if applicable as shown in illustration C.
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certied under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Go to for more information on replacement parts and installation videos.columbiasinks.com
Tools Required
Tape measure
Adjustable wrench
Drill motor and drill bits
Pipe wrench
Level
Safety glasses
Screw drivers: phillips and standard
Pencil
Socket wrench
Illustration A
Illustration B
Illustration C


Produkt Specifikationer

Mærke: Sani-Lav
Kategori: Køkkenvask
Model: 56FBL

Har du brug for hjælp?

Hvis du har brug for hjælp til Sani-Lav 56FBL stil et spørgsmål nedenfor, og andre brugere vil svare dig




Køkkenvask Sani-Lav Manualer

Sani-Lav

Sani-Lav 58FFL Manual

15 Juni 2025
Sani-Lav

Sani-Lav 531FA Manual

15 Juni 2025
Sani-Lav

Sani-Lav 510F1 Manual

15 Juni 2025
Sani-Lav

Sani-Lav 510FS Manual

15 Juni 2025
Sani-Lav

Sani-Lav 532A Manual

15 Juni 2025
Sani-Lav

Sani-Lav 512F0 Manual

15 Juni 2025
Sani-Lav

Sani-Lav 54F1 Manual

15 Juni 2025
Sani-Lav

Sani-Lav 56FK1 Manual

15 Juni 2025
Sani-Lav

Sani-Lav 56F1 Manual

15 Juni 2025
Sani-Lav

Sani-Lav 531FB Manual

15 Juni 2025

Køkkenvask Manualer

Nyeste Køkkenvask Manualer