Sedona L500CART Manual

Sedona Ikke kategoriseret L500CART

Læs gratis den danske manual til Sedona L500CART (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Sedona L500CART, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Assembly Instructions:

SEDONA L400CART

L500CART

& L600CART

Lynx Freestanding Cart

Model L400CART, L500CART &L600CART

Lynx Grills, Inc., 6023 E. Bandini Blvd. Commerce, CA 90040 Phone: (323)838‐1770 Fax: (323)838‐1778 | www.lynxgrills.com

Document 33807 Rev C 02/08/13

Step 1.

Step 2.

Step 3.

Step 1.

After opening and identifying the components, select the back

panel assembly and either the right or left side panel assembly.

Orient the parts as shown in the illustration for step 1.

Note that these parts are upside down with the shelves at the

floor. Hook the right or left side to the back into the four keyways

located on the edge. When attached all four keyways should be

engaged and the back and side flush to the top.

Repeat this step for the opposite side panel.

Step 2.

With the cart oriented upside down, locate the 4 - #8 screws and

nuts and mount the electrical transformer to the access plate

shown in the illustration for this step. It may be done at the end of

the assembly but is somewhat easier to access at this stage.

Step 3.

Refer to the figure for step 3 and insert the base assembly into the

cavity at the back corners of the cabinet. Check that the tank hole

is positioned as shown and the magnet is located on the open side.

Splay the two sides out slightly and enclose them over the front of

the base. The sides and back have pockets that fit over the casters

for clearance. Use 4 of the ¼-20 x ½ screw at each corner to lock

the assembly in place.

Access

Plate

magnet

tank

hole

Screw

4 places

Introduction:

Your Freestanding Cart comes with all of the components necessary

to assemble a cart for the SEDONA Series of Lynx Grills.

The SEDONA CART series is comprised of 8 sub assemblies:

1. Back Panel Assembly

2. Right Side Panel Assembly with Shelf

3. Left Side Panel Assembly with Shelf

4. Base Assembly with Wheels

5. Inner Shelf Assembly

6. Cross Brace Assembly

7. Right Door

8. Left Door

In addition there are 14 screws (1/4 -20 x ½) to assemble the

cart and grill and 4 screws with nuts (#8-32 x 3/8) to attach the

transformer assembly supplied with the Grill.

Produkt Specifikationer

Mærke:	Sedona
Kategori:	Ikke kategoriseret
Model:	L500CART

Har du brug for hjælp?

Hvis du har brug for hjælp til Sedona L500CART stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Sedona Manualer

Sedona VC600F Manual

26 December 2024

Sedona L500F-NG Manual

29 August 2024

Sedona L500F-LP Manual

29 August 2024

Sedona L1500LP Manual

29 August 2024

Sedona LIJ600 Manual

29 August 2024

Sedona VC30ADA Manual

29 August 2024

Sedona L1600NG Manual

29 August 2024

Sedona L700CART Manual

29 August 2024

Sedona L700PSFR NG Manual

29 August 2024

Sedona L2500LP Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Philips Evnia 32M3C3540 Manual

30 Oktober 2025

Soler & Palau DUOVENT MODULAR XL DV Manual

30 Oktober 2025

Iogear GCS1228TAA3 Manual

30 Oktober 2025

Abus E212 Manual

30 Oktober 2025

Olimpia Splendid Bi2 SLIR Manual

30 Oktober 2025

EtherWAN EX24402 Manual

30 Oktober 2025

Abus Smartvest Pro APP45200 Manual

30 Oktober 2025

EtherWAN ED3501 Manual

30 Oktober 2025

Sage the Puck Sucker SCA800 Manual

30 Oktober 2025

Wimberley AP-606 Manual

30 Oktober 2025