Sedona S36CART Manual

Sedona Ikke kategoriseret S36CART

Læs gratis den danske manual til Sedona S36CART (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Sedona S36CART, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Assembly Instructions:

SEDONA L400CART

L500CART

& L600CART

Lynx Freestanding Cart

Model L400CART, L500CART &L600CART

Lynx Grills, Inc., 6023 E. Bandini Blvd. Commerce, CA 90040 Ph

Document 33807 Rev C 02/08/13

Step 1.

Step 2.

Step 3.

Step 1.

Aer opening and idenfying the components, select the back

panel assembly and either the right or le side panel assembly.

Orient the parts as shown in the illustraon for . step 1

Note that these parts are upside down with the shelves at the

oor. Hook the right or le side to the back into the four keyways

located on the edge. When aached all four keyways should be

engaged and the back and side ush to the top.

Repeat this step for the opposite side panel.

Step 2.

With the cart oriented upside down, locate the 4 - #8 screws and

nuts and mount the electrical transformer to the access plate

shown in the illustraon for this step. It may be done at the end of

the assembly but is somewhat easier to access at this stage.

Step 3.

Refer to the gure for and insert the base assembly into the step 3

cavity at the back corners of the cabinet. Check that the tank hole

is posioned as shown and the magnet is located on the open side.

Splay the two sides out slightly and enclose them over the front of

the base. The sides and back have pockets that t over the casters

for clearance. Use 4 of the ¼-20 x ½ screw at each corner to lock

the assembly in place.

Access

Plate

magnet

tank

hole

Screw

4 places

Introducon:

Your Freestanding Cart comes with all of the components necessary

to assemble a cart for the SEDONA Series of Lynx Grills.

The SEDONA CART series is comprised of 8 sub assemblies:

1. Back Panel Assembly

2. Right Side Panel Assembly with Shelf

3. Le Side Panel Assembly with Shelf

4. Base Assembly with Wheels

5. Inner Shelf Assembly

6. Cross Brace Assembly

7. Right Door

8. Le Door

In addion there are 14 screws (1/4 -20 x ½) to assemble the

cart and grill and 4 screws with nuts (#8-32 x 3/8) to aach the

transformer assembly supplied with the Grill.

Step 4.

Step 5.

To begin turn the cabinet upright to secure the step 4

Inner Shelf Assembly. The and shelf will only L400 L500

assemble as shown at the right with the electrical hole to

the rear and the screws mounng at the back and le

side. The shelf is not only useful but necessary for the

proper stability of the cart. omit the inner shelf DO NOT

or any part in these instrucons.

The inner shelf is secured by 4 of the ¼-20 x ½ screws.

Two through the back and two through the le side.

The shelf as shown here assemble L600 will

the same as above.

Step 5 L400/L500 is the last assembly on the cart before

installing the Grill to the cart. The cross brace ts into

recesses located at the front edge of the cart above the

hinge brackets. Orient the brace with the center magnet

facing forward and posioned such that the magnet is

higher than center rather than lower. Install the brace from

the backside of the anges and align the nutcerts each at

end with the holes provided for the screws. The brace is

secured by 2 of the ¼-20 x ½ screws.

The door frame is aached along with the cross brace . L600

Support the cross brace from the backside of the front

anges. Align the nutcerts each end with the holes at

provided for the screws. Posion the door frame over the

nutcerts and cross brace , and secure them both with the ¼-

20 x ½ screws.

Step 4 .

L400

L500

Step 4 .

L600

Step 5.

L400

L500

Step 5.

L600

Produkt Specifikationer

Mærke:	Sedona
Kategori:	Ikke kategoriseret
Model:	S36CART

Har du brug for hjælp?

Hvis du har brug for hjælp til Sedona S36CART stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Sedona Manualer

Sedona VC600F Manual

26 December 2024

Sedona L500F-NG Manual

29 August 2024

Sedona L500F-LP Manual

29 August 2024

Sedona L1500LP Manual

29 August 2024

Sedona LIJ600 Manual

29 August 2024

Sedona VC30ADA Manual

29 August 2024

Sedona L1600NG Manual

29 August 2024

Sedona L700CART Manual

29 August 2024

Sedona L700PSFR NG Manual

29 August 2024

Sedona L2500LP Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM SU9030 Manual

13 September 2025

IFM O2U554 Manual

13 September 2025

Speco Technologies HTi70TM Manual

13 September 2025

QSC RMXa Manual

13 September 2025

Tineco Floor One S2 Series Manual

13 September 2025

Tineco Floor One S3 Breeze Manual

13 September 2025

Tineco Floor One S5 Steam Manual

13 September 2025

Osram VX500-CB Manual

13 September 2025

Zelmer ZTS7990 Manual

13 September 2025

Osram VX250-SP Manual

13 September 2025