Shure Microflex MX418SE Manual

Shure Mikrofon Microflex MX418SE

Læs gratis den danske manual til Shure Microflex MX418SE (12 sider) i kategorien Mikrofon. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Shure Microflex MX418SE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

GENERAL

Shure Microflex MX400SE Series microphones are miniature

gooseneck-mounted electret condenser microphones designed

for speech and vocal pickup. Their high sensitivity and broad fre-

quency range make them suitable for recording, as well as sound

reinforcement applications.

MX400SE microphones can be screwed onto a mic stand or the

supplied 5/8 inch 27-threaded flange. They can be easily changed

from side-exit to bottom-exit to conceal the cable. All models in-

clude an in-line preamplifier and a 3 m (10 ft) cable. Each micro-

phone is available with interchangeable cardioid, supercardioid, or

omnidirectional cartridges.

FEATURES

•Wide dynamic range and frequency response for accurate

sound reproduction across the audio spectrum

•Interchangeable cartridges that provide an optimal polar

pattern choice for each application

•Balanced transformerless output for increased immunity to

noise over long cable runs

•Supplied shock mount for more than 20 dB isolation from

surface transmitted noise

wSupplied threaded flange mount for permanently securing the

microphone to a lectern, pulpit, or conference table

•Snap-fit foam windscreen

MODEL VARIATIONS

All Microflex microphones are available with any one of three

interchangeable cartridges. The polar pattern is indicated by the

model number suffix:

/C = Cardioid, /S = Supercardioid, /O = Omnidirectional

MX412SE/C, MX418SE/C: Recommended for general sound rein-

forcement applications. Pickup angle (–3 dB) = 130°.

MX412SE/S, MX418SE/S: Recommended for sound reinforce-

ment applications requiring narrow or more distant coverage.

Pickup angle (–3 dB) = 115°.

MX412SE/O, MX418SE/O: Recommended for recording or remote

monitoring applications. Pickup angle = 360°.

GENERAL INSTALLATION GUIDELINES

1. Aim the microphone toward the desired sound source, such as

the talker, and away from any unwanted sound source, such

as a loudspeaker.

2. Place the microphone within 15 to 30 cm (6 to 12 in.) of the de-

sired sound source.

3. Always use the supplied foam windscreen or the optional met-

al windscreen to control breath noise.

4. If four or more microphones will be open at the same time, use

of an automatic mixer, such as the Shure SCM810 or FP410,

is recommended.

MICROPHONE INSTALLATION

Installing a Microphone onto a Threaded Flange (Figure 1)

1. Trace and drill three starter holes for the supplied screws using

the threaded flange as a template.

2. Secure the flange to the mounting surface using the three sup-

plied screws.

3. Thread the microphone onto the flange.

Installing a Microphone in a Shock Mount (Figure 2)

1. Drill a 44 mm (1-3/4 in.) diameter hole through the mounting

surface in the desired location.

2. Trace and drill three starter holes for the screws using the

shock mount as a template.

3. Secure the shock mount to the mounting surface with three

screws.

4. Thread the microphone onto the supplied shock mount adapt-

er and insert the adapter into the shock mount.

Changing from Side Exit to Bottom Exit (Figure 3)

1. Unscrew the preamplifier cap.

2. Loosen the retaining screw and push the XLR plug up until the

circuit board screw terminals are accessible.

3. Remove the cable from the screw terminals, and slide the cap

off of the cable.

4. Push the outer threaded nut on the microphone back to access

the inner hex nut on the bottom of the gooseneck.

5. Unscrew the inner hex nut from the gooseneck. Then remove

the outer threaded nut.

6. Insert the cable through the outer threaded nut, then through

the inner hex nut.

7. Replace the outer threaded nut on the gooseneck.

8. Screw the inner hex nut back onto the gooseneck.

9. Install the flange mount or shock mount, and route the cable

though the center of the mount.

10. Reinsert the cable through the preamplifier cap.

11. Reconnect the cable to the preamplifier screw terminals (Red

to R; Black to B; Shield to S) and wrap the cable around strain

relief notches. Then screw the preamplifier cap back on tight.

Installing the Snap-Fit Foam Windscreen (Figure 4)

1. Press the foam windscreen onto the microphone until it snaps

into the groove located below the cartridge.

2. To remove the windscreen, spread the gap in its mounting ring

with a screwdriver or thumbnail and pull the windscreen off

carefully.

Microflex MX400SE Series

Gooseneck MicrophoneUser Guide

27F2835 (BG)

2002, Shure Incorporated Printed in U.S.A.

Produkt Specifikationer

Mærke:	Shure
Kategori:	Mikrofon
Model:	Microflex MX418SE

Har du brug for hjælp?

Hvis du har brug for hjælp til Shure Microflex MX418SE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Mikrofon Shure Manualer

28 September 2025

1 September 2025

22 August 2025

18 August 2025

22 Juli 2025

Shure PGA56-XLR Manual

15 Juli 2025

Shure ULXD6 Manual

23 Juni 2025

Shure MoveMic One Manual

21 Februar 2025

Shure MV7i Manual

21 Februar 2025

Shure VP89M Manual

29 December 2024

Mikrofon Manualer

Nyeste Mikrofon Manualer

Nady SP-R3 Manual

4 November 2025

Phenyx Pro PTU-7000A Manual

4 November 2025

JARO J100-CS Manual

4 November 2025

MayBesta WM150 Manual

3 November 2025

XIAOKOA N80-B Manual

3 November 2025

Singing Machine CPK565 Manual

3 November 2025

Shaevle SW-16 Manual

3 November 2025

HOTEC H-U25 Manual

3 November 2025

Saramonic Blink500 B3 Manual

3 November 2025

SGPRO D-332 Manual

2 November 2025