Signature Hardware Swing Spout 426713 Manual


Læs gratis den danske manual til Signature Hardware Swing Spout 426713 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Signature Hardware Swing Spout 426713, eller vil du spørge andre brugere om produktet?

Side 1/3
1
S W I N G S P O U T
WALL MOUNT FAUCET
SKU: 380330, 416234, 416235, 416236, 416237, 420969, 426713
REVISED 02/19/2020
CODES: 443738, 443709, 443711
443713, 443715, 443716, 482232
GETTING STARTED
BEFORE YOU BEGIN
We recommend consulting a professional if you are
unfamiliar with installing plumbing �xtures. Signature
Hardware accepts no liability for any damage to the
faucet, plumbing, sink, counter top, wall, or for personal
injury during installation.
Observe all local plumbing and building codes.
Unpack and inspect the faucet for shipping damage. If
any damage is found, contact our Customer Relations
team at 1-8 -55 71 18005- .
Ensure that you have gathered all the required
materials that are needed for the installation.
For these instructions, it is assumed that the old
faucet has been completely removed and any neces-
sary repairs or modi�cations to the water supply have
been completed.
TOOLS AND MATERIALS:
Plumbers
Tape
Thread
Sealant
Adjustable
Wrench
Phillips
Screwdriver
PLANNING
Use the faucet’s PDF speci�cation sheet as a reference
when planning your installation. The speci�cation sheet
can be found and downloaded from the product page
on our website.
Because the faucet speci�cation measurements are
approximate and slight variations may occur, we highly
recommend performing any rough-in procedures with
the faucet on site.
Drop Ear Elbow
(x2)
For Warranty information, please visit: signaturehardware.com/services/warranty
1 855 715 1800. . .
2
S W I N G S P O U T
WALL MOUNT FAUCET
SKU: 380330, 416234, 416235, 416236, 416237, 420969, 426713
INSTALLATION
3. Insert one of the provided rubber O-rings into each of
the faucet inlets, as shown. Connect the faucet to the
installed wall couplers. Apply plumbers tape or thread
sealant to the threads before attaching. Tighten �rmly.
4. Attach the spout to the installed faucet body.
Tighten the nut �rmly using an adjustable wrench, but
be careful not to overtighten.
1. Prepare the in-wall plumbing for faucet installation. a
pair of drop ear elbows will need to be roughed in
behind the wall, 8” apart on-center, to make the
connection to the faucet.
Important: Be sure to consider the total thickness of
the �nished wall, including tile (if applicable), when
calculating how far back to rough-in the elbows.
PROCEED WITH THE CONSTRUCTION OF THE
FINISHED WALL. ONCE THE FINISHED WALL HAS
BEEN COMPLETED, RESUME FAUCET
INSTALLATION.
2. Connect the faucets wall couplers to the installed
drop ear elbows. Use any pipe nipples and adapters
necessary to make the connection. Apply plumber’s
tape or thread sealant to the threads before connect-
ing.
8”
Rubber O-Ring
1 855 715 1800. . .


Produkt Specifikationer

Mærke: Signature Hardware
Kategori: Ikke kategoriseret
Model: Swing Spout 426713

Har du brug for hjælp?

Hvis du har brug for hjælp til Signature Hardware Swing Spout 426713 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Signature Hardware Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer