Singer 29K72 Manual

Singer Symaskine 29K72

Læs gratis den danske manual til Singer 29K72 (13 sider) i kategorien Symaskine. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Singer 29K72, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/13
DESCRIPTION
Machines 29K71, 29K72 and 29K73, for stitching boots, shoes, and other tubular work in leather and fabrics, have the
following characteristics:
Single Needle, lock Stitch.
Stop Motion Hand Whee1-releases hand wheel from stitching mechanism for bobbin winding.
Horizontal Oscillating Shuttle.
Eccentric Adjustment for Shuttle Timing.
Cylinder Bed.
Replaceable Steel Horn.
Universal Upper Feed for Stitching in any direction without turning the work.
Stitch length: 7 to 15 to the inch, depending on material being stitched and operations performed.
Presser Foot rise during feeding action: 1/4 inch -(Maximum clearance: 3/8 inch).
Double End Needle Plate -(two sizes of needle holes at each end for various sizes of needles).
Adjustable Thread Take-up lever.
Two Speed Machine Pulley.
ACCESSORIES AVAILABLE UPON ORDER
(At additional charge)
Attachment for fitting Hand Wheel on front of machine (Part No.821211)
Stand for mounting the machine 601405 or 601407 for foot power.
601406 or 601408 for electric power.
Detachable Work Table for flat stitching operations (Part No. 83739, 83740, or 83741).
Electric Transmitter S-9.
SPECIAL FEATURES
MACHINE 29K71 (Was 29K53)
End of cylinder bed is 1 inch wide and 7/8 inch deep.
Space at right of need1e 12- 1/4 inches.
Diameters of belt grooves 2-7/8 inches and 4-7/8 inches.
MACHINE 29K72
End of cylinder bed is 1-5/32 inches wide and 1-1/16 inche5 deep.
Space at right of needle 17-1/2 inches.
Diameters of belt grooves 3-1/4 inches and 5.1/2 inches.
Large Bobbin.
MACHINE 29K73
End of cylinder bed is 1 inch wide and 7/8 inch deep.
Space at right of needle 17-1/2 inches.
Diameters of belt grooves 3-1/4 inches and 5-1/2 inches.
1
SPEED
The maximum speed recommended for these machines is
500 stitches per minute, depending on material being
stitched and operations performed.
For thick work, patching, mending, and stitching elastics
put the driving belt on the larger pulley of the machine and
the smaller pulley of the stand.
For light work, put the belt on smaller pulley of the
machine and the larger pulley of the stand.
When in operation, the hand wheel must always turn over
toward the operator (counter-clockwise).
NOTE: If fitted on front of machine, hand wheel must
always turn over toward the right (clockwise).
TO OIL MACHINE
Fig. 2. Oiling Front Side of Machine
When machine is received from the factory, it should be
thoroughly cleaned and a drop of oil should be applied to
all parts indicated in Figs. 2, 3 and 4.
Apply a drop of oil to the stand at the centres upon which
band wheel and treadle work. Also to both ends of the
pitman rod connecting the treadle with band wheel.
Run machine for a few minutes to work oil into bearings.
When the machine is in constant use, it should be oiled
daily.
Fig. 3. Oiling Rear of Machine
Use "TYPE B" or "TYPE D" OIL sold by Singer Sewing
Machine Company.
See inside front cover of this book for description of these
oils.
Fig. 4. Oiling Shuttle Race
To oil shuttle race, raise needle bar to its highest point and
lift feeding foot A, Fig. 5 by moving lifter B upward.
Press down lever C, Fig. 5 and swing needle plate to
position shown in Fig. 4.
Apply a drop of oil to the face of shuttle race and to the
hole shown by arrow in Fig. 4.
2

Produkt Specifikationer

Mærke: Singer
Kategori: Symaskine
Model: 29K72

Har du brug for hjælp?

Hvis du har brug for hjælp til Singer 29K72 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Symaskine Singer Manualer

Singer

Singer Futura 430 Manual

8 September 2025
Singer

Singer Damppresser Manual

7 September 2025
Singer

Singer Needle Guide Manual

22 August 2025
Singer

Singer C5900 Manual

1 August 2025
Singer

Singer C620L Manual

1 August 2025
Singer

Singer M2505 Manual

1 August 2025
Singer

Singer Stylist 9100 Manual

1 August 2025
Singer

Singer Heavy Duty HD6605C Manual

30 Juni 2025
Singer

Singer HD 6705C Manual

31 Maj 2025
Singer

Singer Little Touch & Sew 67A Manual

5 Februar 2025

Symaskine Manualer

Nyeste Symaskine Manualer

Bernette

Bernette b68 Maker Manual

3 Oktober 2025
Necchi

Necchi N 422 Manual

28 September 2025
Necchi

Necchi L234A Manual

27 September 2025
Necchi

Necchi Prima 263 Manual

27 September 2025
Necchi

Necchi NC-103D Manual

27 September 2025
Necchi

Necchi N 424 Manual

27 September 2025
Necchi

Necchi 559 Manual

27 September 2025
Necchi

Necchi M108A Manual

27 September 2025
Necchi

Necchi M213A Manual

27 September 2025
Necchi

Necchi NC-204D Manual

27 September 2025