Singer 29K73 Manual
Læs nedenfor 📖 manual på dansk for Singer 29K73 (13 sider) i kategorien Symaskine. Denne guide var nyttig for 4 personer og blev bedømt med 4.3 stjerner i gennemsnit af 2.5 brugere
Side 1/13
DESCRIPTION
Machines 29K71, 29K72 and 29K73, for stitching boots, shoes, and other tubular work in leather and fabrics, have the
following characteristics:
Single Needle, lock Stitch.
Stop Motion Hand Whee1-releases hand wheel from stitching mechanism for bobbin winding.
Horizontal Oscillating Shuttle.
Eccentric Adjustment for Shuttle Timing.
Cylinder Bed.
Replaceable Steel Horn.
Universal Upper Feed for Stitching in any direction without turning the work.
Stitch length: 7 to 15 to the inch, depending on material being stitched and operations performed.
Presser Foot rise during feeding action: 1/4 inch -(Maximum clearance: 3/8 inch).
Double End Needle Plate -(two sizes of needle holes at each end for various sizes of needles).
Adjustable Thread Take-up lever.
Two Speed Machine Pulley.
ACCESSORIES AVAILABLE UPON ORDER
(At additional charge)
Attachment for fitting Hand Wheel on front of machine (Part No.821211)
Stand for mounting the machine 601405 or 601407 for foot power.
601406 or 601408 for electric power.
Detachable Work Table for flat stitching operations (Part No. 83739, 83740, or 83741).
Electric Transmitter S-9.
SPECIAL FEATURES
MACHINE 29K71 (Was 29K53)
End of cylinder bed is 1 inch wide and 7/8 inch deep.
Space at right of need1e 12- 1/4 inches.
Diameters of belt grooves 2-7/8 inches and 4-7/8 inches.
MACHINE 29K72
End of cylinder bed is 1-5/32 inches wide and 1-1/16 inche5 deep.
Space at right of needle 17-1/2 inches.
Diameters of belt grooves 3-1/4 inches and 5.1/2 inches.
Large Bobbin.
MACHINE 29K73
End of cylinder bed is 1 inch wide and 7/8 inch deep.
Space at right of needle 17-1/2 inches.
Diameters of belt grooves 3-1/4 inches and 5-1/2 inches.
1
SPEED
The maximum speed recommended for these machines is
500 stitches per minute, depending on material being
stitched and operations performed.
For thick work, patching, mending, and stitching elastics
put the driving belt on the larger pulley of the machine and
the smaller pulley of the stand.
For light work, put the belt on smaller pulley of the
machine and the larger pulley of the stand.
When in operation, the hand wheel must always turn over
toward the operator (counter-clockwise).
NOTE: If fitted on front of machine, hand wheel must
always turn over toward the right (clockwise).
TO OIL MACHINE
Fig. 2. Oiling Front Side of Machine
When machine is received from the factory, it should be
thoroughly cleaned and a drop of oil should be applied to
all parts indicated in Figs. 2, 3 and 4.
Apply a drop of oil to the stand at the centres upon which
band wheel and treadle work. Also to both ends of the
pitman rod connecting the treadle with band wheel.
Run machine for a few minutes to work oil into bearings.
When the machine is in constant use, it should be oiled
daily.
Fig. 3. Oiling Rear of Machine
Use "TYPE B" or "TYPE D" OIL sold by Singer Sewing
Machine Company.
See inside front cover of this book for description of these
oils.
Fig. 4. Oiling Shuttle Race
To oil shuttle race, raise needle bar to its highest point and
lift feeding foot A, Fig. 5 by moving lifter B upward.
Press down lever C, Fig. 5 and swing needle plate to
position shown in Fig. 4.
Apply a drop of oil to the face of shuttle race and to the
hole shown by arrow in Fig. 4.
2
Produkt Specifikationer
| Mærke: | Singer |
| Kategori: | Symaskine |
| Model: | 29K73 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Singer 29K73 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Symaskine Singer Manualer
31 Maj 2025
5 Februar 2025
2 Februar 2025
6 Januar 2025
31 December 2025
31 December 2025
24 December 2024
24 December 2024
24 December 2024
24 December 2024
Symaskine Manualer
- Symaskine Feiyue
- Symaskine Guzzanti
- Symaskine Bernina
- Symaskine Ambiano
- Symaskine LERAN
- Symaskine Sinbo
- Symaskine Emerio
- Symaskine Dürkopp Adler
- Symaskine Termozeta
- Symaskine Home Electric
- Symaskine Anker-Bernette
- Symaskine Hema
- Symaskine Jocca
- Symaskine Baby Lock
- Symaskine Meister Craft
Nyeste Symaskine Manualer
10 Juni 2025
4 Marts 2025
4 Marts 2025
4 Marts 2025
4 Marts 2025
4 Marts 2025
4 Marts 2025
12 Februar 2025
6 Februar 2025
6 Februar 2025