Sony XS-GTF1025B Manual

Sony Bilhøjttaler XS-GTF1025B

Læs gratis den danske manual til Sony XS-GTF1025B (2 sider) i kategorien Bilhøjttaler. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Sony XS-GTF1025B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Precautions

• Do not continuously use the speaker

system beyond the peak power handling

capacity.

• Keep recorded tapes, watches, and

personal credit cards using magnetic

coding away from the speaker system to

protect them from damage caused by the

magnets in the speakers.

If you cannot find an appropriate mounting

location, consult your car dealer or your

nearest Sony dealer before mounting.

Installation/Connections

安装/线路连接

 2007 Sony Corporation Printed in China

XS-GTF1025B

3-213-895- (1)21

Unit: mm

单位：mm

Dimensions

尺寸

10cm Coaxial

2-way Speaker

24.5

ø 117

ø 91.5

ø 65

6 × 9

ø 102.5

Specifications

Speaker Coaxial 2-way:

Woofer 10 cm, HOP, cone

type

Tweeter 2.5 cm,

B.D. type

Peak power 130 W*1

Rated power 30 W*1

Impedance 4 Ω*1

Sensitivity 88

2 dB (1 W, 1 m)*2

Frequency response 45 Hz – 25,000 Hz*1

Mass Approx. 400 g per speaker

Supplied accessory Parts for installation

Design and specifications are subject to change

without notice.

*1Testing Condition : IEC60268-5 (2003-05)

*2Testing Condition : EIAJ RC-8124A

部件名称

扬声器

附件

有毒有害物质或元素

铅

（Pb）汞

（Hg）镉（Cd）六价铬（Cr（VI））多溴联苯（PBB）多溴二苯醚（PBDE）

×a a a a a

产品中有毒有害物质或元素的名称及含量

a ：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。

× ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。

(a∶不含有

，

×∶含有)

ø 142

使用前注意事项

•请勿超过峰值功率处理能力连续使用扬声器

系统。

•请将录制的磁带、手表和使用磁性码的个人

信用卡远离扬声器系统放置，以防止被扬声

器中的磁体损坏。

如果您找不到适当的安装位置，请在安装前向

您的汽车经销商或附近的Sony经销商咨询。

规格

扬声器同轴型 2 声道:

低音扬声器 10 cm，高度定

向聚稀烃，锥型

高音扬声器2.5 cm，B.D.型

峰值功率 130 W*1

额定功率 30 W*1

阻抗 4 Ω*1

灵敏度 88

2 dB (1 W, 1 m)*2

频率响应 45 Hz - 25000 Hz*1

近似质量 400 g/扬声器

随机提供安装附件

设计和规格如有变更，恕不另行通知。

*1测试条件等依据：IEC60268-5(2003-05)

*2测试条件等依据：EIAJ RC-8124A

Parts list/部件表

Mounting/安装 Mounting from the car interior/从汽车内安装

How to remove the grille net.

如何取下格栅网。

Before Mounting

A depth of at least 43 mm is required for flush

mounting. Measure the depth of the area where

you are to mount the speaker, and ensure that

the speaker is not obstructing any other

components of the car. Keep the following in

mind when choosing a mounting location:

•Make sure that nothing is obstructing around

the mounting location of the door (front or

rear) where you are to mount the speaker.

•A hole for mounting may already be cut out of

the inner panel of the door (front or rear). In

this case, you need to modify the board only.

•If you are to mount this speaker system in the

door (front or rear), make sure that the speaker

terminals, frame or magnet do not interfere

with any inner parts, such as the window

mechanism in the door (when you open or

close the window), etc.

Also make sure that the speaker grille does not

touch any inner fittings, such as the window

cranks, door handles, arm rests, door pockets,

lamps or seats etc.

安装之前

嵌入式安装至少需要 43 mm 深度。请测量您要安

装扬声器的位置深度，并确保扬声器不会妨碍汽

车上的任何其他部件。选择安装位置时，请注意

下列事项：

• 确保您要安装扬声器的车门（前或后）的安装位

置周围没有障碍物。

• 车门（前或后）的内面板上可能已经开有安装

孔。在此情况下，您只需改装底板。

• 如果您要将扬声器系统安装在车门（前或后）

内，请确保扬声器端子、框架或磁体不会干扰任

何内部部件，例如车门上的车窗机械装置（当您

打开或关闭车窗时）等。

同时，也请确保扬声器格栅不会碰到任何内部装

置，例如车窗摇柄、车门把手、扶手、门套、灯

或座位等。

Flat mounting (installed flush with the surface of the dash)/ 平面安装(与仪表板表面齐平安装)

This speaker can be made to fit in almost any type of car by removing

the mounting tabs.

Use clippers or pliers, etc. to cut or snap the mounting tabs off so

that it is even with the edge of the speaker frame as illustrated.

Note

After removing the mounting tabs, handle the speaker frame with

care, as the edges may be sharp.

去除安装翼片后，此扬声器几乎可适合安装在任何类型的汽车上。

用剪刀或钳子等工具剪去或钳断此安装翼片，且如图所示正好与扬声器框

的边缘齐平。

注意

在去除安装翼片后，由于扬声器外框边缘可能较锋利，请小心操作。

ø 91 mm

× 2

× 8

ø 4 30×

× 8

× 2

Press and insert the edges of the grille net.

按下并插入格栅网的边缘。

6 5

Striped cord

条纹电线

* White cord — Left speaker

Grey cord — Right speaker

* 白色电线左扬声器 —

灰色电线右扬声器 —

To speaker cord of a car.

至汽车扬声器电线。

8 mm

13 mm

2Remove the grille net.

取下格栅网。

1Mark the 4 bolt holes and make them 3.3 mm in diameter.*

画出4个螺栓孔，并钻成 3.3 mm* 直径的孔。

* When using : 4ø 5 mm

* 使用 4 时：ø 5 mm

Door panel

门板

ø 3.3 mm*

ø 92 mm

Produkt Specifikationer

Mærke:	Sony
Kategori:	Bilhøjttaler
Model:	XS-GTF1025B

Har du brug for hjælp?

Hvis du har brug for hjælp til Sony XS-GTF1025B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bilhøjttaler Sony Manualer

Sony XS-N1640 Manual

9 August 2025

Sony XS-N1620C Manual

9 August 2025

Sony XM-504X Manual

22 Juli 2024

Sony XS-AW200X Manual

27 April 2024

22 December 2023

31 Oktober 2023

5 Oktober 2023

25 September 2023

8 September 2023

2 September 2023

Bilhøjttaler Manualer

Nyeste Bilhøjttaler Manualer

Mac Audio Performance X 2.16 Manual

30 September 2025

Phoenix Gold ZDSV6C Manual

19 September 2025

AudioControl PNW-1 Manual

10 September 2025

Rockville RM88PRO Manual

9 September 2025

Focal ISUB BMW 8 Manual

7 September 2025

Audison Voce AVK 6A P II Manual

27 August 2025

Audison Voce AV 3.0 II Manual

27 August 2025

Audison Prima AP 6.5P Manual

27 August 2025

Audison Voce AV 6.5 P II Manual

27 August 2025

Audison Voce AVK 6 S II Manual

27 August 2025