Supermicro SuperServer 5019C-MR Manual

Supermicro Server SuperServer 5019C-MR

Læs gratis den danske manual til Supermicro SuperServer 5019C-MR (16 sider) i kategorien Server. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Supermicro SuperServer 5019C-MR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/16

Information for Lot 9 of d )ErP (Eco esign

This addresses Ecodesign addendum European Union (EU) requirements for servers and storage products.

All data and ratings within this addendum are in reference only to the in thSupermicro product(s) e

manual. the The below information conforms to requirements laid down in Annex II of Commission

Regulation . 2019/424

3(1)(a): See Section 1.1 of the system manual for the product type.

3(1)(b): e See the title page and preface of th system manual for trademark and the

manufacturer’s address.

3(1)(c): See the title page of the system manual for product model number(s).

3(1)(d): See the serial number on the physical system to determine the year . of manufacture

3(1)(e-j ): PSU Efficiency V ) (f and Power Factor alue (Table rom 80 Plus report)

PSU Model #: PWS- - 407 1R

Watts: 400W

PSU E fficiency

P Fower actor

% of R Lated oad

% % % %10 20 50 100

50 %

Single -Output (AC DC)

85.64%

92.05%

94.43%

93.17%

0.98

System (EUT) E P fficiency in I Sdle tate ower (Table)

Representative

Configurations

Measured Idle State

Power (W)

Calculated Idle Power Allowance

(W)

High-End Performance

Configuration

68.4

214.55

Typical Configuration

N/A

Low-End Performance

Configuration

45.2

180.33

System E(EUT) fficiency in A Sctive tate P ower (Table)

Representative

Configurations

Active tate S

E Sfficiency core

(Effserver)

Minimum A S ctive tate Efficiency

High-End Performance

Configuration

14.4

Typical Configuration

N/A

Low-End Performance

Configuration

13.7

3(1)( ): k is . The operating condition class A2

Dry bulb temp °C

Humidity range, non condensing-

Operating

condition

class

Allowable

range

Recom 

mended

range

Allowable range

Recommended range

Max dew

point (°C)

Maximum

rate of

change

(°

C/hr)

15 32-

18 27-

–

12 and °C P Dew oint (DP)

8 % relative humidity (RH) to

17 ° and 80 C DP % RH

–

9 °C DP to

15 °C and DP

60 % RH

5/20

10 35-

18 27-

–

12 and °C DP 8 % RH to

21 and 80 °C DP % RH

Same as A1

5/20

5-40

18 27-

–

12 and °C DP 8 % RH to

24 and 85 °C DP % RH

Same as A1

5/20

5-45

18 27-

–

12 and °C DP 8 % RH to

24 and 90 °C DP % RH

Same as A1

5/20

3(1)( ): l The idle state power at the higher boundary temperature of the operating conditions

class is W. 80.71

3(1)( ): m The active state efficiency and performance a minimum of is 13.7.

3(1)(n): There are two methods by which a user can securely delete data from this system. The

user performing secure data deletion should be an IT professional.

The first is with a Unified Extensible Firmware Interface (UEFI) shell utility. This utility

works on X10/X11/H11/H12/M11 motherboard series with onboard SATA/NVMe devices.

Any user may access and download this y through following link: utilit

https://www.supermicro.com/about/policies/disclaimer.cfm?url=/wftp/utility/Lot9_Secure

_Data_Deletion_Utility/

Download the shell utility package and extract it to a USB flash drive, then plug the drive

into the server for which secure data deletion is necessary. Then turn the system on.

Navigate to the BIOS setup menu, then place the server system into the UEFI shell

environment. Follow the instructions in the README file to invoke the utility and

complete the deletion.

The second method is through the secure data deletion tool provided by the original

manufacturer of the hard drive. This should be used in a scenario where the shell utility

is not applicable. Each manufacturer should have the tool available on their website. If

needed, please look on the hard drive label for the name of the manufacturer and model

informatio n.

3(1)( ): o List of recommended combinations of blade servers with chassis: N/A.

3(1)(p): List of all current SKUs within this product family: N/A.

3(3)(a): There is no use of cobalt in batteries in this product.

Produkt Specifikationer

Mærke:	Supermicro
Kategori:	Server
Model:	SuperServer 5019C-MR

Har du brug for hjælp?

Hvis du har brug for hjælp til Supermicro SuperServer 5019C-MR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Server Supermicro Manualer

Supermicro SuperServer 6028TR-DTR Manual

7 September 2025

Supermicro SuperServer SYS-620BT-DNTR Manual

28 August 2025

Supermicro SuperServer 2029U-E1CR4 Manual

28 August 2025

Supermicro Blade SBI-411E-1G Manual

28 August 2025

Supermicro SuperServer AS-1114S-WN10RT Manual

28 August 2025

Supermicro SuperServer 1029U-TRT Manual

22 August 2025

Supermicro SuperServer AS -2024US-TNR Manual

21 August 2025

Supermicro SuperServer AS-2024US-TRT Manual

21 August 2025

Supermicro SuperServer SYS-221BT-HNC8R Manual

23 Juli 2025

Supermicro SuperServer 1019S-MC0T Manual

6 Juli 2025

Server Manualer

Nyeste Server Manualer

Ibm eServer xSeries 346 Manual

13 September 2025

Ibm BladeCenter HS23 Manual

13 September 2025

Ibm eServer System x3850 X5 Manual

13 September 2025

Ibm eServer xSeries 445 Manual

13 September 2025

Ibm System x x3690 X5 Manual

13 September 2025

Ibm eServer xSeries 206 Manual

13 September 2025

Ibm xSeries 365 Manual

13 September 2025

Ibm System x x3650 M3 Manual

13 September 2025

Ibm System x3650 M3 Manual

13 September 2025

Ibm System x x3950 X5 Manual

13 September 2025