Technoline WS 6810 Manual

Technoline Vejrstation WS 6810

Læs gratis den danske manual til Technoline WS 6810 (1 sider) i kategorien Vejrstation. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Technoline WS 6810, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

SNOOZE

Outdoor Remote

Temperature

Sensor

Battery

Door

E0060

Instruction Manual

Radio Controlled

LED

Clock with Wireless Indoor

and Outdoor Temperature

I n s e r tt

AC/DC

adaptor plug

Indoor Temperature

dimmers

witch

Outdoor

Temperature

Insert

AAA

back up

batteries

lnstallation

Plug the AC/DC adaptor into any 230V European AC household outlet.

Plug the DC jack into the the back of clock. The front of the clock will show

Battery Back Up

Slide the battery door at the back case, insert 3 x

AAA

batteries with correct

and

polarity signs inside the battery compartment.

Replace the battery cover.

When AC power is

off,

the batteries will power the clock to keep track of the time and alarm time.

When only the back

up batteries is used, the LED panel is off.

Power Up Reception and Signal Strength Display

Afterplug in AC power, the clock starts to receive DCF signal. lcon

blinks. Display shows

When strong DCF signal is detected, display shows with

bars

When weak or no DCF signal is detected, display shows with 1

bar

You will need to place the dock to another area for

better reception, or unplug the AC/DC jack to start over reception again

During reception, the signal strength may move from

bar to

bars to

bars. This is normal since the clock

is detecting DCF signal and other

signals in the air at the same time.

3. If the clock does not catch DCF time signal for

minutes, it will go

back to normal time display

During reception, press TlME button once will go to normal time display. Press

HR again will return to reception mode and signal strength indication.

Successful reception or failed

reception

loon becomes static on (stop blinking) when reception is successful

loon disappears when reception is failed

Weak

signa

detected

Successful

Reception

Failed

Reception

Automatic Reception and Manual

Reception

2:00 am. If fails at 2:00 am, it will start again at 3:00 am.

Automatic reception

this clock starts reception automatically everyday at : 1:00am. If auto reception fails at 1:00 am, it will start again at

If auto reception fails at 3:00 am still fails,

will start reception every

hours until it succeed to catch correct DCF time.

Manual reception

press HR button once anytime to start manual reception of DCF time signal. The LED time display will go to radio

controlled reception mode

tower

lcon blinking

Strong

DCF signal

detected

minute digits

may

start counting

02 0 3 60

02 trying

matchwith the correct seconds

JJY

signal

To Set

Time

and Alarm Time

After power up, if press TIME button once, time digits go to 0:00am default

start

up The clock time). continues to receive signal. The DCF icon is still blinking.

Press HR button once will go back to radio controlled reception mode (as above)

TO SET TlME

Press and hold TlME button and at same the time press HR button once at a time to

set

hour.

Press and hold TlME button and at same the time press MIN button once at a time to minute. set

TO SET ALARM

TlME

Slide the Alarm Switch to ALM 1

Press and hold ALM button and at the same time press HR button once at a time to set hour.

Press and hold ALM button and at the same time press MIN button once at a time to

set

minute.

SET ALARM

TlME

Slide the Alarm Switch to ALM

Press and hold ALM button and at the same time press HR button once at a time to set hour.

Press and hold ALM button and at the same time press MIN button once at a set time to minute.

TO TURN ON/OFF ALARM

or/and ALARM

To turn on Alarm

only, slide the alarm switch to ALM 1

ALM 1

LED lights up on upper left

the hour digits.

To turn on Alarm

only, slide the alarm switch to ALM

ALM

LED lights up on lower left of the hour digits.

To turn on both Alarm

and

slide the alarm switch to ALM 1

both ALM

and ALM 2 LED light up.

To in

activate both Alarm 1

and

permanently, slide to ALM OFF. Both ALM

and ALM

LED turn oﬀ.

TO USE THE SNOOZE ALARM

When time reaches the set ALARM 1

and or /ALARM

time, the dock will beep with the ALM

andlor ALM

LED blinking.

Press the SNOOZE button once, the alarm sound will stop and ALM

or ALM

LED keep blinking. Alarm will sound again

minutes.

STOP THE ALARM

When time reaches the set ALARM

andlor ALARM

time, the dock will beep with the ALM 1

and or /ALM

LED blinking.

Press and hold the SNOOZE button for

seconds, the alarm sound will stop ALM and 1

or ALM

LED becomes static.

Alarm

andlor Alarm 2 will sound again same time next day.

TO TURN OFF ALARM 1

AND/OR ALARM

PERMANENTLY

Slide the alarm switch to ALM OFF. Alarm sound will stop and both ALM

and ALM

LED'S turn off.

SET SNOOZE DURATION (from

minutes)

Press and hold and time display SNOOZE will show

(default duration) and then snooze press MINUTE button to set your

desired snooze duration.

READ MAXIMUM

MINUMUM INDOOR

OUTDOOR TEMPERATURES

Simply press the button to view the maximum indoor and outdoor temperatures. Press CLEAR to reset the Max readings.

The readout will now appear as

and will start to record the maximums again.

Then press the button to view the minimum indoor and outdoor temperatures. Press CLEAR reset the to Min readings.

The readout will now appear as

and will start to record the minimums again.

IF YOU LOSE THE OUTDOOR TEMPERATURE

When the outdoor temperature digits show

'---'l,

the wireless transmission is either interrupted or lost. Press the RESET button

located on the back of the outdoortransmitter. If you continue to lose outdoor temperature the display, try placing the transmitter in a different

location until you have smooth transmission

temperature data.

TROUBLE SHOOTING

Press the RESET button on the back of the base thermometer and then press RESET button located on the back of the outdoor transmitter.

Once you do this, your

clock

will be reset to default setting and needs to

dated by DCF time signal again.??

USE THE HI

L0 DIMMER SWITCH

Simply slide the LO

HI DIMMER at switch the back of the clock to adjust the LED brightness to a level comfortable to you in the dark.

CARE OF YOUR CLOCK

Do not expose your clock to extreme temperatures, water or direct sunlight.

2. Avoid contact with any corrosive materials

Do not subject the clock to excessive force, dust humidity or

Do not inner back case tamper open the or

with

any components of this dock

Do not plug in any adaptor other AC/DC wi thincorrect specifications or voltage

Produkt Specifikationer

Mærke:	Technoline
Kategori:	Vejrstation
Model:	WS 6810
Produktfarve:	Sort
Indbygget skærm:	Ja
Ur-funktion:	Ja
Alarmfunktion:	Ja
Målefunktioner:	Indoor thermometer, Outdoor thermometer
Trend visning af målefunktioner:	Termometer
Vejrstation, extremum data:	Termometer
Min. /maks. Temperatur-hukommelse:	Ja
Alarm for målefunktioner:	Ja