Totolink T10 Manual

Totolink Router T10

Læs gratis den danske manual til Totolink T10 (2 sider) i kategorien Router. Denne vejledning er vurderet som hjælpsom af 85 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 43 anmeldelser. Har du et spørgsmål om Totolink T10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick Installation Guide

Smart wireless coverage router

Appearance

Mesh

Connect the Master to the Internet

2.1. Diagram of a Master’s network

Q1: How can I connect to the router’s wireless network for the first time?

A1: Use the Wi-Fi network name (SSID) located on the router label, and no

password is required.

Q2: Why cannot the router web’s interface appear when I attempt to log in to the

router?

A2:

● Try to configure your computer to obtain an automatic IP address from the

router. For clicking the Start menu, selecting Windows 7, do this by Control

Panel > Network and Internet Change > Network and Sharing Center >

adapter settings Local Area Connection, right-clicking and choosing

Properties > Networking > Internet Protocol Version 4 (TCP/IPv4) >

Properties Obtain an IP address automatically, and then selecting

radio button.

● Make sure the router’s IP address you input is 192.168.0.1.

● Use another web browser and try again.

● Reboot the router and try again.

Q3: Why cannot I access the Internet when the Master is configured using my ISP

settings?

A3:

● Check that the Internet is available. To do this, connect your computer

directly to the ut whetherInternet port on your Modem or the wall, and find o

your computer can use the connection. If so, check further your router.

Otherwise, contact your ISP for support and service.

● Set up the router again by referring to section “Set up the Master’s network”.

● Reboot your modem and router, and try again.

Create your whole home Wi-Fi system

This section includes one Master and two Satellites to work together to create

a seamless Mesh Wi-Fi network in a two-story house. A maximum of three

Satellites can be used to sync to a single Master at the same time.

There are two methods of sync between one Master and two Satellites.

One is achieved using the panel T button, the other via the Master’s Web

interface.

Troubleshooting

Model: T10

Website: http://www.totolink.net

Information in this document is subject to change without prior notice.

All the routers can be seen and set as the Master or Satellite. They can be both

configured in the same way. The section chooses one router as the Master and

introduces how to make it access the Internet. In this case, the other routers are

used as the Satellites and don’t need to be set up like this router, but just kept in

their original states for later use in your home Wi-Fi system together with this router

to be configured.

Internet

Router (Master)

Power adapter

Outlet

Tablet

Smartphone

2.2. Use a browser to access the Master

1 Connect yo. ur computer to any of the Master’s LAN ports using an Ethernet cable.

2. Plug the Master into an electrical outlet.

3 Set your computer to obtain an IP address automatically. For more information,.

see section “Troubleshooting”.

4 Launch a web browser..

6 Enter the login user name and password and click the button.. LOGIN

user name and password both are . They are case-sensitive.The default admin

● Use the supplied power adapter or one only where all design specifications are met.

● Place the router on a flat and stable surface.

● Leave proper clearance around the router.

● Prevent the router from sources of heat or fire. Heat may cause it to catch fire or

its housing to melt.

● Unplug the router and remove all of its cables during lightning storms or when

unused for a long period.

● Do not expose the router to rain, moisture, sprays, drips or splashes.

2.3. Set up the Master’s network

Note:

The following explains three Internet connection types.

● PPPoE: service provider (ISP) for user name and password. ask your Internet

● DHCP: This option requires no user action. Your Master works as a DHCP

client and is automatically assigned the IP configuration from your ISP.

● ask your ISP for the settings such as IP address, Subnet Mask, Static IP:

Default Gateway, and DNS.

c. Enter the user name and password provided by your ISP.

1. Log in to the Master with a browser.

2 Specify the Internet connection..

a port is connected to the Ethernet. Before setup, ensure that the Master’s WAN

port on a Modem or the wall.

b In the list, select a type such as .. WAN Connection Type PPPoE

SZ83830116@163.gd

3 Configure the wireless settings in 5G and 2.4G bands..

In and area, wireless names (SSIDs) and5G 2.4G Wireless set your network

passwords.

TOTOLINK_5G_XXXXXX (5G by default)● Network Name (SSID):

and TOTOLINK_XXXXXX (2.4G by default).

XXXXXX is the last six characters from the Master’s MAC address.

You can set the SSID manually.

ssword. The password must contain east● Password: Enter the wireless pa at l

eight letters, numbers, or symbols, but no more than 63 characters.

4. Click the button.Apply

5G band

TOTOLINK_5G_BC8E70

TOTOLINK

2.4G band

TOTOLINK_BC8E74

TOTOLINK

3.1. Diagram of a Wi-Fi system

3.2. Sync between one Master two Satellites 1. Press and hold the panel T button on the Master for about 3 seconds

until its state LED blinks between red and orange.

2. Wait until the state LEDs on the two Satellites also blink between red

and orange. It may take about 30 seconds.

3. Wait about 1 minute for the state LEDs on the Master to blink green

and on the Satellites solid green. In this case, it means the Master is

synced to the Satellites successfully.

4. Adjust the position of the three routers. As you move them, check that

the state LEDs on the Satellites light solid green or orange until you find a

good location.

5. Use your device to find and connect to any router’s wireless network

with the same SSID and Wi-Fi password that you use for the Master.

※ Method 1: Using the panel T button

1. Log in to the Master via a web browser.

2. Click the button. Advanced Setup

3. Choose , and then click the button.Operation Mode > Mesh Mode Next

4 In the list, select . Mesh Enable to start sync between the Master and the

Satellites.

5 sync to finish. The state LEDs run in the same. Wait about 2 minutes for the

mentioned when using the panel T button. During this process, process as

the Master will reboot automatically. Therefore, your computer may be

disconnected thefrom the Master and log out of Master’s web interface.

You can log in again if you want to see the sync state.

6. Adjust the position of the three routers. As you move them, check that the

state LEDs on the Satellites light solid green or orange until you find a

good location.

7. Use your device to find and connect to any wireless network with the same

Wi-Fi SSID and password that you use for the Master.

※ Method 2: Using the router’s web interface

If you want to view which Satellites are synced to the Master on the Master’s

Web interface, log in to the Master via a web browser, and then go to the

Mesh Networking Information area by choosing

Advanced Setup > System Status.

Note:

1 Internet and configure its SSID and password,. Connect the Master to the

as described in section “Set up the Master’s network”.

2. Ensure that these two Satellites are in factory defaults. If not or uncertain,

reset them by pressing and holding the panel T button for five seconds.

3. Place all the Satellites near the Master, and ensure that the distance

between the Master and Satellite is limited to one meter.

4. Check that all the routers above are applied power.

※ Before sync

5 In the address field of the browser, enter . 192.168.0.1.

http://192.168.0.1/

DHCP

Static IP

PPPoE

DHCP

5 while the . Please wait Master is setting up the network. It may take a minute. If an

Internet connection is established successfully, the message Connection is

successful! appears.Whether it’s connected or not, SSID and wireless password

are changed when this period of time elapses.

Connection is successful !

You have successfully completed the parameters that all the routers need to configure

Back Finished

7 The . Easy Setup interface displays. You can now change the Master’s settings.

TOTOLINK_5G_BC8E70

TOTOLINK_BC8E74

Front Panel State LED

(Recessed)

T Button

Rear Panel

LAN Ports

WAN Port

DC Power Port

LED Name

State LED

(Recessed)

Solid green

Blinking green

Blinking alternately

between red and

orange

● The router is booting. The process finishes until the state LED

blinks green. It may take about 40 seconds; please wait.

● It means the Satellite is synced to the Master successfully, and

the connection between them is strong.

● The router finishes the booting process and is working normally.

● It means the Master is synced to the Satellite successfully.

The sync is being processed between the Master and Satellite.

● The Master and Satellite failed to sync.

● The connection between the Master and Satellite is poor.

Consider moving the Satellite closer to the Master.

Solid red (Satellite)

The Satellite is synced successfully to the Master, and the

connection between them is good.

Solid orange

(Satellite)

While the reset process is being proceeded.Blinking red

LED Activity Description

Button/Ports

T Button

● Reset Router to factory defaults: when the router is powered on, press this

button and hold it for 5 seconds until the state LED blinks red.

● Sync Master to Satellites: press and hold this button on a router for about 3

seconds until the state LED blinks alternately between red and orange. This way,

this router is set as the Master to sync to the surrounding Satellites.

LAN Ports

WAN Port

● Connect to an Ethernet port on a Modem or the wall for Internet access in

Router (Gateway) mode.

● Used as a LAN port in Bridge, Repeater, WISP mode, or on the Satellites in the

Mesh Wi-Fi system.

Connect to PCs or switches with Ethernet cables.

Connect to an electrical outlet with the supplied power adapter. DC Power Port

Description

Caution

admin

Satellite SatelliteSatellite Satellite

Master

Satellite (Original state)

Internet access

one meter maximum

Disable

Enable

Q5: I wonder if the previous settings on the Satellites such as SSID and wireless

password will change when they are synced to the Master.

A5: Multiple settings like SSID and password configured on the Satellites before are

changed to configuration parameters on the Master synced. Therefore, use the

Master’s wireless setup for internet access.

Q6: Do I need to sync a Satellite to the Master again if I reboot it?

A6: No, you don’t. The Satellite will automatically attempt to sync to its Master

connected earlier when you restart it as long as it’s in factory defaults.

Q7: What should I do if I want to add another Satellite to the existing Mesh Wi-Fi

system?

A7: You just your Satellite to the Wi-Fi system rather than sync againneed to sync

-Fi . To perform this action, place theall the existing Satellites in the Wi system

Satellite within one meter from the Master, press and hold the panel T button

on the Master for about three seconds, and the sync process starts. For more

information, see section “Sync between one Master two Satellites”.

Q4: Why cannot the Master and Satellite sync successfully?

A4:

● Check that the Satellites are in factory defaults. If not or uncertain, reset

them by pressing and holding the panel T button for five seconds.

● Ensure that the distance between the Master and Satellite are limited to one meter.

● Check that all the routers are connected to power sources.

● Make sure that your routers are equipped with the latest firmware. To do this,

try to check for updates available by visiting www.totolink.net.

V1.0 | 2017-11-17

单色/80G书纸 840x105MM

Produkt Specifikationer

Mærke:	Totolink
Kategori:	Router
Model:	T10
Vekselstrømsindgangsspænding:	100 - 240 V
Vekselstrømsindgangsfrekvens:	50/60 Hz
Bredde:	89 mm
Dybde:	89 mm
Højde:	68.5 mm
Produktfarve:	Beige,Black
Produkttype:	Bordplade router
USB-port:	Ingen
Opbevaringstemperatur (T-T):	-40 - 70 °C
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Relativ luftfugtighed ved opbevaring (H-H):	5 - 95 %
Ethernet LAN-porte (RJ-45):	2
Ethernet LAN:	Ja
Wi-Fi-standarder:	802.11a,Wi-Fi 5 (802.11ac),802.11b,802.11g
Forældrekontrol:	Ja
Strømforbrug (typisk):	12 W
Driftstemperatur (T-T):	0 - 50 °C
Ethernet LAN-datahastigheder:	10,100,1000 Mbit/s
Sikkerhedsalgoritmer:	WDS,WPS
Husmateriale:	Plast
Indikatorlampe:	Ja
Hurtig installationsvejledning:	Ja
Kabler inkluderet:	LAN (RJ-45)
Pakketype:	Kasse
Ethernet WAN:	Ja
DSL WAN:	Ingen
SIM-kort slot:	Ingen
3G/4G kompatibilitet USB-modem:	Ingen
WAN forbindelsestype:	RJ-45
Wi-Fi-bånd:	Dual-band (2,4 GHz / 5 GHz)
Bedste Wi-Fi standard:	Wi-Fi 4 (802.11n)
WLAN dataoverførselshastighed (maks):	867 Mbit/s
WLAN dataoverførselshastighed (første bånd):	300 Mbit/s
WLAN dataoverførselshastighed (anden bånd):	867 Mbit/s
Ethernet LAN-grænsefladetype:	Gigabit Ethernet
Kabelteknologi:	10/100/1000Base-T(X)
Netværksstandarder:	IEEE 802.11a,IEEE 802.11ac,IEEE 802.11b,IEEE 802.11g,IEEE 802.11n,IEEE 802.11s
Modtager, følsomhed:	2.4G: 11b: <-81dbm；\n 11g: <-68dbm；\n 11n: HT20<-65dbm HT40: <-62dbm\n\n5G: 11a:<-68dbm；\n 11n: HT20<-65dbm HT40: <-62dbm \n 11ac: <-51dbm
DC-in-stik:	Ja
Hukommelseskortstik:	Ingen
DHCP-klient:	Ja
DHCP-server:	Ja
Universal Plug and Play (UPnP):	Ja
Antennedesign:	Intern
Webbaseret administration:	Ja
Knap til nulstilling:	Ja
Servicekvalitet support (QoS):	Ja
Firewall:	Ja
IP-adresse filtrering:	Ja
Filtrering:	Ja
LED-indikatorer:	Status
Strømkilde type:	DC
Udgangsspænding:	12 V
Udgangsstrøm:	1 A
AC-adapter inkluderet:	Ja
Plug and play:	Ja
Strøm over Ethernet (PoE):	Ja
Adgangskontrolliste (ACL):	Ja
Filtrering af MAC-adresser:	Ja
Aftagelig (e) antenne (r):	Ingen
Strømforsyning:	12 W
URL-filtrering:	Ja
Understøttelse af DMZ:	Ja
MU-MIMO-teknologi:	Ja
Intelligent gitterteknologi:	Ja