Tripp Lite HCINT350SNR Manual

Tripp Lite Ikke kategoriseret HCINT350SNR

Læs gratis den danske manual til Tripp Lite HCINT350SNR (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Tripp Lite HCINT350SNR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

17-12-143 - EN Revised by V Li 08/22/2017 .

HC350S, HCINT350S Series Power Module Application Guidelines

Series AGSM5396, AGRT0829

SAVE THESE INSTRUCTIONS IMPORTANT SAFETY This manual contains –

INSTRUCTIONS for that should be followed during installation and maintenance of the

UPS and batteries.

The HC350S and HCINT350S series of hospital cart power modules are designed to

provide AC voltage output power from either utility provided AC input voltage or from

inverting 12VDC power from a sealed lead acid battery. To ensure proper operation the

following guidelines should be observed:

1. The power module can support AC loads up to a maximum of 400VA or 300W.

2. The power module charger is intended to be used with a 12V sealed lead acid

absorbed glass mat (AGM) battery with a 33AH to 66AH rating. Batteries rated

at less than 33AH are not recommended since the charger current of 12A would

reduce the battery cycle life of smaller batteries.

3. Adequate provision for airow needs to be provided at both the inlet and outlet

vents of the power module. There should be at least 0.5 inches of clear space

on the fan end and on the vented end of the power module. A bae or air

deector is recommended at the fan end so that the air intake is raised at least 6

inches above oor level to prevent dust accumulation inside the power module.

4. The power module may be mounted in any orientation. Four 8-32 threaded

inserts are provided on the surface with the AC input cord to facilitate mounting.

5. The AC voltage input and output connections are made with user supplied cables

to the IEC input and output connectors on the power module. Use only with

approved plug/cord sets according to the equipment electrical ratings. No

external fusing is needed since safe operation is assured by internal non-

replaceable 10A fuses. However, if a customer wishes to prevent the internal

fuses from blowing in the event of an extreme overload, then an external fuse or

circuit breaker rated at 6A to 10A (120VAC models) or 3A to 5A (230V models)

should be provided on the AC voltage input.

6. The 12V battery input is made with a user supplied cable to the Anderson DC

connector on the power module. Proper polarity must be observed. The

recommended wire size is 8AWG in order to keep the voltage drop in the cable to

less than 0.1V. The length of cable between the battery and the power module

should be less than 30 inches. A user supplied 40A to 50A automotive style fuse

is required in the positive lead of the battery (within 18 inches of the battery

positive terminal).

7. Additional bonding is needed to connect the battery negative terminal to the case

of the power module. The wire (or metal frame of the cart) should be short (less

than 18 inches) and preferably of the same gauge as the other battery wires

17-12-143 - EN Revised by V Li 08/22/2017 .

(although a minimum gauge of 16AWG has been acceptable). This bonding

connection is necessary to prevent internal damage to the power module in the

event of any accidental reversed polarity connections or accidental connections

between the battery positive wiring and the case of the power module.

8. A Remote User Interface (RUI) module must be connected to the power module

using two CAT-5 cables. The COMM1 jacks should be connected together and

the COMM2 jacks should be connected together. If the cables are not connected

or if they are interchanged, the power module will not operate. The RUI may be

either a Tripp Lite RUI or a customer designed RUI that meets Tripp Lite

specications.

9. The power module includes a low voltage cuto (LVC) function that will remove

any load on the battery when the battery is depleted. The LVC level is about

10.5V to assure optimum battery cycle life. If any other DC loads are present in

the system, they need to include their own LVC function in order to prevent

damage to the battery due to over discharge.

10. The power module will not turn on unless connected to a battery that has a

voltage greater than 9.6V. If the battery voltage is less than 9.6V, it is assumed

to be defective and the charger is inhibited in order to prevent possible

outgassing of the battery.

11. The power module reports % Battery Capacity through its USB port. This data is

most accurate when a 55AH sealed lead acid absorbed glass mat (AGM) battery

is used. Batteries of other capacities may be used, but the accuracy of the

% Battery Capacity report will be reduced.

12. After connecting a battery to the power module, the power module should be

allowed to charge the battery to full capacity in order to initialize the % Battery

Capacity report and the % Battery Capacity LED’s (on the RUI). This will take at

least 4 hours, even with fresh battery. The % Battery Capacity report and LED’s

will not be accurate until after the initial charge has been completed. After

initialization, the power module will properly indicate the % Battery Capacity as

the battery is repeatedly discharged and recharged. However, each time the

battery is replaced, the initialization will need to be repeated.

Produkt Specifikationer

Mærke:	Tripp Lite
Kategori:	Ikke kategoriseret
Model:	HCINT350SNR

Har du brug for hjælp?

Hvis du har brug for hjælp til Tripp Lite HCINT350SNR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Tripp Lite Manualer

Tripp Lite BHDBT3-USB Manual

28 September 2025

Tripp Lite PDUMV30HV Manual

28 September 2025

Tripp Lite PDUMV30 Manual

12 August 2025

Tripp Lite Isobar ISOBLOK2-0 Manual

12 August 2025

Tripp Lite SRIN4181810 Manual

1 August 2025

Tripp Lite Protect It! TLP74RB Manual

1 August 2025

Tripp Lite SPS610HGRA Manual

1 August 2025

Tripp Lite N286-100G-SR4SA Manual

1 August 2025

Tripp Lite Protect It! TLP88USBB Manual

1 August 2025

Tripp Lite Protect It! TLP664USBB Manual

1 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Sony AIBO ERS-7M2 Manual

3 Oktober 2025

AFK EWK-2200.73C Manual

3 Oktober 2025

TOA TS-D1000-DU Manual

3 Oktober 2025

Zoom G1M Manual

3 Oktober 2025

Arris Touchstone TM902 Manual

3 Oktober 2025

Inkbird PTH-10C Manual

3 Oktober 2025

Rowenta Professional DW8115 Manual

3 Oktober 2025

AFK EWK-2200.5 Manual

3 Oktober 2025

Realme GT3 Manual

3 Oktober 2025

Supermicro SuperServer SYS-110D-4C-FRAN8TP Manual

3 Oktober 2025