Tripp Lite PS3612B Manual


Læs gratis den danske manual til Tripp Lite PS3612B (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Tripp Lite PS3612B, eller vil du spørge andre brugere om produktet?

Side 1/4
1
Power Strips
Models: PS120406, PS120410, PS120420, PS240406,
PS2408, PS2408B, PS2408RA, PS240810, PS3612,
PS3612B, PS3612RA, PS361206, PS361220,
PS480806, PS4816, PS4816B, PS6020, PS7224,
PS7224-20 and PS7224-20T
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2016 Tripp Lite. All rights reserved.
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com
Owner’s Manual
PS-Series Power Strips are designed to provide convenient access to multiple AC outlets.
Note: The Power Strip models listed above DO NOT provide your connected equipment
with surge or line-noise protection.
Important Safety Instructions 2
Equipment Connection 2
Wall Mounting 2
Specifications 3
Warranty and 4
Product Registration
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an
ISOBAR6ULTRA surge protector—
a $100 value!
www.tripplite.com/warranty
(AGIB7019) (AGIB7019)
16-08-002-93361B-EN.indd 1 8/24/2016 3:01:29 PM
2
Equipment Connection
Plug your equipment into the Power Strip’s AC receptacles. DO NOT plug in equipment that draws
more total amps than your Power Strip’s amperage rating (see label on Power Strip for amperage
rating), or you will trip the circuit breaker. If the circuit breaker trips, remove overload and depress
breaker to reset. Leave enough clearance at the end of the Power Strip to allow the circuit
breaker to operate normally.
Note: Select models with a power switch feature a protective switch cover. To access the switch, flip open the
attached cover.
Wall Mounting
All Power Strip models feature clips for horizontal or vertical mounting on a variety of surfaces.
The user must supply other mounting hardware (screws, etc.) and determine its suitability for use
with the chosen mounting surface.
1 Mark a straight horizontal or vertical line where
you want to mount the Power Strip. At each end
of the line, mark where the edges of the Power
Strip will be located. Place a mounting clip on
the mounting surface 1” in from these edges
and mark where the screws must be driven into
the wall. For strips longer than 48” (120 cm),
also mark a screw hole for a third mounting clip
midway between the other two. 1
Important Safety Instructions
SAVE THESE INSTRUCTIONS
DO NOT connect the power strip to an ungrounded outlet.
DO NOT use the power strip with 2-wire extension cords or adapters.
This power strip is designed for indoor use only. Install the power strip away from heat-emitting
appliances such as radiators or heat registers.
Do not install where excessive moisture is present.
Do not plug extension cords into the power strip.
Never install electrical, telephone, network or coaxial wiring during a lightning storm.
Do not drill into any part of the housing or open the housing for any reason. There are no
user-serviceable parts inside.
Use of this equipment in life support applications where failure of this equipment can
reasonably be expected to cause the failure of the life support equipment or to significantly
affect its safety or effectiveness is not recommended. Do not use this equipment in the
presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.
16-08-002-93361B-EN.indd 2 8/24/2016 3:01:30 PM


Produkt Specifikationer

Mærke: Tripp Lite
Kategori: Ikke kategoriseret
Model: PS3612B

Har du brug for hjælp?

Hvis du har brug for hjælp til Tripp Lite PS3612B stil et spørgsmål nedenfor, og andre brugere vil svare dig