Tripp Lite SmartRack SR42UBCL Manual

Tripp Lite Ikke kategoriseret SmartRack SR42UBCL

Læs gratis den danske manual til Tripp Lite SmartRack SR42UBCL (36 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Tripp Lite SmartRack SR42UBCL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/36

Table of Contents

1. Important Safety Instructions 2

2. Overview 2

3. Feature Identiﬁcation 3

4. Enclosure Installation 3

4.1 Preparation 3

4.2 Unpacking 4

4.3 Placement 5

4.4 Leveling 5

4.5 Ground Connection 6

5. Enclosure Conﬁguration 6

5.1 Adding or Removing Front and Rear Doors 6

5.1.1 Removing Doors 6

5.1.2 Reinstalling Doors 6

5.2 Reversing Doors 7

5.3 Adding or Removing Roof Panel 8

5.3.1 Removing Roof Panel 8

5.3.2 Reinstalling Roof Panel 8

5.4 Adding or Removing Side Panels 8

5.4.1 Removing Side Panel 8

5.4.2 Reinstalling Side Panels 9

5.5 Combining (Baying) Enclosures 9

6. Combination Locks 10

6.1 Setting and Resetting the Combination Lock 10

6.2 Using the Combination Lock 10

7. Equipment Installation 11

7.1 Cage Nuts 11

7.1.1 Installing Cage Nuts 11

7.1.2 Removing Cage Nuts 11

8. Speciﬁcations 12

9. Storage and Service 12

10. Warranty and Warranty Registration 12

Español 13

Français 25

SmartRack™ Enclosures

Models: SR42UBCL, SR48UBCL

Owner’s Manual

WARRANTY

REGISTRATION

to win a FREE Tripp Lite product

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA

(773) 869-1234 • www.tripplite.com

1. Important Safety Instructions

2. Overview

SAVE THESE INSTRUCTIONS

All sections of this manual contain instructions and warnings that should be followed during the installation and use of the SmartRack Enclosures

described in this manual. Read all instructions and warnings thoroughly before attempting to move, install or use the SmartRack Enclosures described in

this manual. Failure to comply will create a risk of personal injury and property damage and may invalidate the warranty.

• Keep the enclosure in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses, conductive contaminants, dust and

direct sunlight.

• Leave adequate space at the front and rear of the enclosure for proper ventilation. Do not block, cover or insert objects into the external ventilation openings ofthe

enclosure.

• The enclosure is extremely heavy. Use caution when handling the enclosure. Do not attempt to unpack, move or install it unassisted. Use a mechanical device such as a

forklift or pallet jack to move the enclosure in the shipping container.

• Do not place any object on the enclosure, especially containers of liquid, and do not attempt to stack the enclosures.

• Inspect the shipping container and the enclosure for shipping damage. Do not use the enclosure if it is damaged.

• Leave the enclosure in the shipping container until it has been moved as close to the final installation location as possible. The casters are designed for minor position

adjustments within the final installation area only. The casters are not designed for moving the enclosure over longer distances.

• The casters are not designed to provide long-term support for the enclosure after final installation. Use the levelers to provide long-term support.

• Install the enclosure in a structurally sound area with a level floor that is able to bear the weight of the enclosure, all equipment that will be installed in the enclosure

and any other enclosures and/or equipment that will be installed nearby.

• Do not push the enclosure from the side panels to move it. Pushing from the side panels will cause a tipping hazard.

• When rolling the enclosure on its casters, always push it from behind, never pull it toward you.

• A rolling enclosure can cause personal injury and property damage if not properly supervised. If rolling the enclosure down a ramp is required, use extreme caution.

Do not attempt to use ramps that have a slope steeper than 1:12.

• Use caution when cutting packing materials. The enclosure could be scratched, causing damage not covered by the warranty.

• Save all packing materials for later use. Repacking and shipping the enclosure without the original packing materials may cause product damage that will void the warranty.

• Do not re-ship the enclosure with additional equipment unless the enclosure was shipped with a special shock pallet (“SP1” models only). The combined weight of the

enclosure and installed equipment must not exceed the load capacity of the pallet. Tripp Lite is not responsible for any damage that occurs during re-shipment.

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to

significantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen or

nitrous oxide.

SmartRack Enclosures accommodate all standard

19-inch rackmount equipment, regardless of vendor,

and ship fully assembled for quick and easy

deployment. They feature adaptable, heavy-duty

cabinets in 25U, 42U and 48U heights, with or without

side panels. Several models are available with an

integrated shock pallet that allows resellers, integrators

and enterprise customers to pre-configure equipment

and re-ship the enclosures to the final installation site.

SmartRack Enclosures have variable mounting depths,

ideal for servers. Integrated baying hardware enables

cost-effective, orderly and efficient expansion. The

cabinets include quick-release doors and side panels

for convenient maintenance and split front and front

and rear doors (select models) for improved access and

reduced clearance requirements. Front access doors are

reversible for installation flexibility. Front and rear

doors and side panels are lockable.

Available SmartRack Enclosures

Model # Rack Height Side Panels Shock Pallet

SR25UB 25U Yes No

SR25UBEXP 25U No No

SR25UBSP1 25U Yes Yes

SR25UBEXPSP1 25U No Yes

SR42UB 42U Yes No

SR42UBCL 42U Yes No

SR42UBEXP 42U No No

SR42UBSP1 42U Yes Yes

SR42UBEXPSP1 42U No Yes

SR48UB 48U Yes No

SR48UBCL 48U Yes No

SR48UBEXP 48U No No

SR48UBSP1 48U Yes Yes

SR48UBEXPSP1 48U No Yes

See the Specifications section for more information.

Produkt Specifikationer

Mærke:	Tripp Lite
Kategori:	Ikke kategoriseret
Model:	SmartRack SR42UBCL
Type:	Fritstående reol
Bredde:	600.2 mm
Dybde:	1092.2 mm
Højde:	1993.9 mm
Vægt:	138350 g
Produktfarve:	Sort
Pakkevægt:	154670 g
Pakkedybde:	1155.7 mm
Pakkebredde:	660.4 mm
Pakkehøjde:	2159 mm
Harmoniseret systemkode (HS):	8517.79.0000
Hovedkassen højde (udvendigt):	2159 mm
Hovedkassens længde (udvendigt):	1155.7 mm
Hovedkassens bruttovægt (udvendigt):	154670 g
Hovedkassens bredde (udvendigt):	660.4 mm
Oprindelsesland:	Kina
Produkter pr. hovedkasse (udvendigt):	1 stk
Rackkapacitet:	42U