Tripp Lite SmartRack SRWB12410STR6 Manual

Tripp Lite Ikke kategoriseret SmartRack SRWB12410STR6

Læs gratis den danske manual til Tripp Lite SmartRack SRWB12410STR6 (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Tripp Lite SmartRack SRWB12410STR6, eller vil du spørge andre brugere om produktet?

Side 1/8
Installation Guide
Wire Basket Cable Trays
Models:
SRWB6210STR
(AC8AFB)
SRWB12210STR
(AC8AFC)
SRWB6410STR
(AC8AFD)
SRWB12410STR
(AC8AFE)
SRWB18410STR
(AC8AFF)
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
Copyright © 2019 Tripp Lite. All rights reserved.
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed during the installation and use of all
Tripp Lite Wire Mesh Cable Tray systems. Failure to heed these warnings may affect your warranty.
Installation should only be performed by a qualified installer and in accordance with all national and local electrical and
building codes.
Always wear eye protection when cutting basket tray wire sections.
Cut edges may be sharp. Exercise caution when handling trimmed basket tray during fabrication and installation.
Español 3 • Français 5 • Русский 7
19-07-393-9339DD.indb 1 10/18/2019 11:30:29 AM
2
Preparation and Fabrication
Wire Tray Models and Dimensions
Before proceeding with fabrication, first confirm your wire tray model and dimensions.
Model Sectional View Height Width Depth
SRWB6210STR 2 in. (50 mm) 6 in. (150 mm) 10 ft. (3000 mm)
SRWB12210STR 2 in. (50 mm) 12 in. (300 mm) 10 ft. (3000 mm)
SRWB6410STR
4 in. (100 mm) 6 in. (150 mm) 10 ft. (3000 mm)
SRWB12410STR
4 in. (100 mm) 12 in. (300 mm) 10 ft. (3000 mm)
SRWB18410STR
4 in. (100 mm) 18 in. (450 mm) 10 ft. (3000 mm)
How to Cut Wire Trays
Notes:
Always use side-action bolt cutters.
Angle all cuts away from the new end.
Cut each wire with one clean cut whenever possible.
Remove any sharp edges to eliminate possible damage to cables.
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
Cut the bottom wires first with the underside of the tray
facing up in the order as shown:
To cut the side wires, flip the wire tray over and cut in the
order shown, starting from the top:
Repeat as needed. For various wire cutting patterns and installation diagrams, refer to the documentation included with the
connectors and connector kits (sold separately).
19-07-393 93-39DD_RevA
1
2
4
3
5
6
1
2
4
3
1
2
4
3
19-07-393-9339DD.indb 2 10/18/2019 11:30:29 AM


Produkt Specifikationer

Mærke: Tripp Lite
Kategori: Ikke kategoriseret
Model: SmartRack SRWB12410STR6

Har du brug for hjælp?

Hvis du har brug for hjælp til Tripp Lite SmartRack SRWB12410STR6 stil et spørgsmål nedenfor, og andre brugere vil svare dig