Tripp Lite SmartRack SRX12UBFFD Manual

Tripp Lite Ikke kategoriseret SmartRack SRX12UBFFD

Læs gratis den danske manual til Tripp Lite SmartRack SRX12UBFFD (24 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Tripp Lite SmartRack SRX12UBFFD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/24

Table of Contents

1. Important Safety Instructions 2

2. Overview 3

3. Feature Identification 3

4. Enclosure Installation 4

4.1 Preparation 4

4.2 Unpacking 4

4.3 Installing Casters and Levelers 4

4.4 Placement 4

4.5 Leveling the Enclosure 5

4.6 Ground Connection 5

5. Enclosure Configuration 6

5.1 Door Locks 6

5.2 Reversing the Doors 6

5.3 Mounting Rails 6

5.4 Adjusting Mounting Rail Depth 6

5.5 Cleaning/Replacing Air Filters 7

6. Equipment Installation 7

6.1 Installing or Removing Cage Nuts 7

7. Specifications 8

8. Storage and Service 8

9. Warranty & Warranty Registration 8

Español 9

Français 17

Owner’s Manual

12U SmartRack® Enclosure

Model: SR12UBFFD

Agency Series: AG-04D4 with Fan Enclosure Door (Series: AG-053B)

24U SmartRack Enclosure

Model: SR24UBFFD

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

WARRANTY REGISTRATION

automatically entered to win an ISOBAR®

surge protector in our monthly drawing!

tripplite.com/warranty

1. Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the product described

in this manual. Read all instructions and warnings thoroughly before attempting installation. Failure to comply may affect the

warranty and cause property damage and personal injury.

Connection, Installation and Location Warnings

• This manual includes instructional safeguards for the skilled person installing the cabinet with fans.

• Inspect the shipping container and the unit for shipping damage. Do not use the unit if it is damaged.

• The cabinet with fan is designed to be installed in a commercial location where only adults are normally present.

• Install in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses, conductive contaminants, dust

and direct sunlight.

• For best performance, keep the indoor temperature between 32° F and 104° F (0° C and 40° C).

• Leave adequate space at the front and rear of the enclosure for proper ventilation. Do not block, cover or insert objects into the external ventilation

openings of the enclosure.

• The enclosure is extremely heavy. Use caution when handling the enclosure. Do not attempt to unpack, move or install it unassisted. Use a

mechanical device such as a forklift or pallet jack to move the enclosure in the shipping container.

• Do not place any object on the enclosure, especially containers of liquid, and do not attempt to stack the enclosures.

• Leave the enclosure in the shipping container until it has been moved as close to the final installation location as possible.

• Install the enclosure in a structurally sound area capable of handling the load, or on a level floor that is able to bear the weight of the enclosure, all

equipment that will be installed in the enclosure and any other enclosures and/or equipment that will be installed nearby.

• Use caution when cutting packing materials. The enclosure could be scratched, causing damage not covered by the warranty.

• Save all packing materials for later use. Repacking and shipping the enclosure without the original packing materials may cause product damage

that will void the warranty.

• Do not reship the enclosure with additional equipment unless the enclosure was shipped with a special shock pallet. The combined weight of the

enclosure and installed equipment must not exceed the load capacity of the pallet. Tripp Lite is not responsible for any damage that occurs during

reshipment.

• The casters are designed for minor position adjustments within the final installation area only. The casters are not designed for moving the enclosure

over longer distances.

• When rolling the enclosure on its casters, always push it from behind; never pull it toward you.

• A rolling enclosure can cause personal injury and property damage if not properly supervised. If rolling the enclosure down a ramp is required, use

extreme caution. Do not attempt to use ramps that have a slope steeper than 1:12.

• Be sure to install 25 pounds of equipment in the lower part of the cabinet for stability.

• Install in accordance with National Electrical Code standards ANSI/NFPA 70 and Canadian Electrical Code, Part I, C22.1.

• To reduce the risk of fire, connect only to a circuit provided branch circuit overcurrent protection in accordance with the National Electrical Code,

ANSI/NFPA 70 and the Canadian Electrical Code, Part I, C22.1.

• Be sure to use maximum 20A overcurrent protection, in accordance with the plug/equipment rating, for the installation.

• The equipment must be connected to an earthed ground mains socket-outlet.

• The appliance inlet and plug on the power supply cord is intended to serve as the disconnect device. Ensure the socket-outlet is installed near the

equipment and is made easily accessible.

• Use only approved power cords types SJT in accordance with national regulations.

• Use power cords with a minimum 18 AWG (0.75 mm2) wire gauge.

• Use only power cords with a protective earthing conductor and a socket outlet with an earthing connection.

• When using tools, use eye protection and follow all other safety precautions recommended by the tool manufacturer and required by applicable

regulations.

• The fan does not require routine maintenance, other than filter replacement. Be sure to replace the filter on a routine basis. Do not open the fan for

any reason. There are no user-serviceable parts inside.