Tripp Lite SMX1500LCD Manual

Tripp Lite Ikke kategoriseret SMX1500LCD

Læs gratis den danske manual til Tripp Lite SMX1500LCD (36 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Tripp Lite SMX1500LCD, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/36
Owner’s Manual
SMX1500LCD
Digital UPS System
Series Number: AGSM5510
Not suitable for mobile applications.
Español 8 • Français 15 • Русский 22 • Deutsch 29
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2019 Tripp Lite. All rights reserved.
Important Safety Instructions
SAVE THESE INSTRUCTIONS
The manual contains instructions and warnings that should be followed during the installation, operation and storage of this product.
Failure to heed these warnings will void your warranty.
UPS Location Warnings
• The UPS is designed for indoor use only in a controlled environment,
away from excess moisture, temperature extremes, conductive
contaminants, dust or direct sunlight.
• For best performance, maintain an indoor temperature between 0º C
and 40º C.
• Leave adequate space around all sides of the UPS for proper
ventilation.
• Do not mount unit with its front or rear panel facing down (at any
angle). Mounting in this manner will seriously inhibit the unit’s internal
cooling, eventually causing product damage not covered under
warranty.
UPS Connection Warnings
• Connect the UPS directly to a properly grounded AC power outlet. Do
not plug the UPS into itself; this will damage the UPS.
• Do not modify the UPS plug, and do not use an adapter that
eliminates the UPS ground connection.
• Do not use extension cords to connect the UPS to an AC outlet.
• If the UPS receives power from a motor-driven AC generator, the
generator must provide clean, filtered, computer-grade output.
• The mains outlet supplying power to the UPS should be near the UPS
and easily accessible.
• To remove the UPS from the supply mains, the AC plug serves as a
disconnect device.
Equipment Connection Warnings
• Use of this equipment in life support applications where failure of this
equipment can reasonably be expected to cause the failure of the life
support equipment or to significantly affect its safety or effectiveness
is not recommended.
• Do not connect surge protectors or extension cords to the output of
the UPS. This might damage the UPS and will void the surge protector
and UPS warranties.
Battery Warnings
• The UPS does not require routine maintenance. Do not open the UPS
for any reason. There are no user-serviceable parts inside.
• Batteries can present a risk of electrical shock and burn from high
short-circuit current. Observe proper precautions. Do not dispose of
the batteries in a fire. Do not open the UPS or batteries. Do not short
or bridge the battery terminals with any object. Unplug and
turn off the UPS before performing battery replacement. Use tools
with insulated handles. There are no user-serviceable parts inside
the UPS. Battery replacement should be performed only by
authorized service personnel using the same number and type of
batteries (Sealed Lead-Acid). The batteries are recyclable.
Refer to your local codes for disposal requirements or visit
http://www.tripplite.com/support/recycling-program for recycling
information. Tripp Lite offers a complete line of UPS System
Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite on the Web at
http://www.tripplite.com/products/battery-finder/ to locate the specific
replacement battery for your UPS.
• Do not attempt to add external batteries to the UPS.
2
Quick Installation
1 Place the UPS in a horizontal or vertical (tower) position.
To install the UPS in a 4-post or 2-post rack, remove the mounting hole covers from the top and
bottom sides of the UPS A. To install the UPS in a 4-post rack, attach the mounting ears to
each side of the UPS using the included hardware B. To install the UPS in a 2-post rack, attach
the mounting ears to each side of the UPS using the included hardware C. With the help of an
assistant (if needed), lift the UPS and attach it to a standard rack with user-supplied hardware.
Caution: If the UPS is installed in a rack, allow at least 2 cm (0.75 in.) clearance
above and below the unit. If the UPS is placed on a flat surface, do NOT stack
any other object directly on top of the unit.
The UPS will stand in a tower position without the aid of the included hardware. For increased
stability, Tripp Lite recommends attaching the included hardware as shown in diagram
D.
In either position, the user must determine the fitness of hardware and procedures before
installation.
Note: The UPS and its included hardware are designed for use with common rack types and may not be
appropriate for all applications.
The LCD display may be rotated to match the orientation of the UPS. To rotate, first carefully
insert a small tool into the slots located on the each side of the LCD. Remove the LCD from the
UPS housing, then rotate and press it back into place.
CAUTION: To safely balance the UPS in a vertical position, make sure the LCD is
located at the top of the front panel.
2 Connect a user-supplied power cord* to the UPS, then plug the UPS into a wall outlet.**
After plugging the UPS into a wall outlet, push the ON/OFF button for one second to turn on the
UPS (see section for more information).Basic Operation
Note: The UPS will not turn on automatically in the presence of live utility power.
*The UPS system does not include an input power cord. The user-supplied power cord should have an IEC-
320 C13 connector (commonly found on detachable power cords for desktop computers) to connect to the
AC input of the UPS.
**Use an outlet that does not share a circuit with a heavy electrical load, such as an air conditioner or
refrigerator.
3 Plug equipment into the UPS.
Insert the female connectors of the detachable power cords that shipped with the UPS system
into the attached equipment’s AC inputs. Insert the male connectors into any of the UPS
system’s available outlets.
The UPS is designed to support electronic equipment only. Connected equipment will overload
the UPS if the total VA ratings for all the equipment connected to the outlets exceeds the UPS
Output Capacity. To find VA ratings, look at equipment nameplates. If the equipment is listed in
amps, multiply the number of amps by 230 volts to determine VA. (Example: 1 amp × 230 volts
= 230 VA). If unsure whether the outlets are overloaded, run a self-test (see MUTE/TEST Button
description for more information).
4 Optional – Connect Communication Cables.
The UPS includes USB and RS-232 communication ports, as well as Tel/DSL/Ethernet surge
protection jacks. These connections are optional, and the UPS will function properly without
these connections.
Not compatible with PoE (Power over Ethernet) applications.
C
B
A
D
CAUTION: The UPS must be plugged into a live AC outlet and powered on for 24 hours after initial installation to fully charge
the internal battery. Connected equipment will receive utility-supplied AC power (if present) immediately after the UPS is
plugged in and turned on, but connected equipment will not receive full battery backup in the event of a blackout or severe
brownout, unless the internal battery is fully charged.

Produkt Specifikationer

Mærke: Tripp Lite
Kategori: Ikke kategoriseret
Model: SMX1500LCD

Har du brug for hjælp?

Hvis du har brug for hjælp til Tripp Lite SMX1500LCD stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Tripp Lite Manualer

Tripp Lite

Tripp Lite U452-000-SD-A Manual

4 Marts 2025
Tripp Lite

Tripp Lite U352-06N-SD Manual

4 Marts 2025
Tripp Lite

Tripp Lite U352-000-MD-AL Manual

4 Marts 2025
Tripp Lite

Tripp Lite SmartRack SRW12US Manual

15 Januar 2025
Tripp Lite

Tripp Lite SmartRack SRIN4101010 Manual

14 Januar 2025
Tripp Lite

Tripp Lite SmartRack SRWALLBRKT2U Manual

14 Januar 2025
Tripp Lite

Tripp Lite SmartRack SRH48UWWD8 Manual

14 Januar 2025
Tripp Lite

Tripp Lite SmartRack SRH48UWDPWD8 Manual

14 Januar 2025
Tripp Lite

Tripp Lite SmartRack SRH48UWDP54WD8 Manual

14 Januar 2025
Tripp Lite

Tripp Lite SmartRack SRH42UWDP54WD8 Manual

14 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Playtive

Playtive IAN 303676 Manual

16 Juni 2025
Playtive

Playtive IAN 307527 Manual

16 Juni 2025
Playtive

Playtive IAN 327441 Manual

16 Juni 2025
Xblitz

Xblitz G750 Pro Manual

16 Juni 2025
Playtive

Playtive IAN 285603 Manual

16 Juni 2025
Playtive

Playtive HG05646 Manual

16 Juni 2025
Milwaukee

Milwaukee M12 IR Manual

16 Juni 2025
Blodgett

Blodgett Invoq 202BG Manual

16 Juni 2025
Aiphone

Aiphone GT-AD Manual

16 Juni 2025
Playtive

Playtive IAN 113608 Manual

16 Juni 2025