Uni-T UT12C Manual

Uni-T Måleudstyr UT12C

Læs gratis den danske manual til Uni-T UT12C (2 sider) i kategorien Måleudstyr. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Uni-T UT12C, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Thank you for purchasing the UT12C and for probe the

full use of the product, please:

----------Read the user manual carefully.

----------strictly observe the safety rules and notes listed

in the manual

Warning:

Please note the following items to guard against electric

shocking or personal injury:

If any damage about the detector or failure to operate,

please do not use it. If any doubt, please deliver the probe

for repair.

Please do not impose voltage exceeding the rating

voltage on probe.

There may be a danger of electric shocking for voltage

higher than 30V (AC), please pay attention to that in

operation and observe local and national safety code of the

country you are in.

I. Electric symbol

Double insulation

Be careful! Electric shocking

Dangerous! Important information, reference manual

CAT IV equipment is intended for protecting from transient

voltage injury resulted by first level power source such as

meter or overhead wires or ground wires infrastructure.

The product meets:

EMC: EN55022:2006+A1:2007

EN61326-1:2006

LVD: EN61010-1:2010

EN61010-031:2002+A1:2008

UL: UL61010-1, 2nd Edition, 2005-07-22

CAN/CSA-C22.2 No.61010-1,2nd Edition,2004-07

Notes:

no contact with the white part of front end of detector body

for your finger!

II. Working voltage and working condition

Working voltage: 90V-1000V AC

Working condition:

1) Temperature: 0°C~40°CWorking

St orage : - 1 0°C~50°CTemperature

Humidity: 95%≤

2) Altitude: 2000m≤

III. Operation instructions

Press once gently the button labeled with

power symbol, buzzer, LED and motor will work

concurrently for 0.5 second, indicating detector

is activated successfully. While entering

the test standby status, LED will flicker two

times continuously with the interval of 1.5

seconds.

Activate

probe

1) Under non-vibration mode, put tip of

detector close to the object being tested with

AC voltage, LED will flick and buzz.

2) Under vibration mode, put tip of detector

close to the object being tested with AC

voltage, LED will flick and buzz and motor

vibrate.

voltage

test

Battery will power off a

utomatically for energy

saving if do not use detector about 3 minutes.

Buzzer and LED will work concurrently 1

second, indicating power off successfully.

Power

off

automatically

Press button gently after power on, LED flickers,

buzzer works, but motor fails to vibrate, a mode

called non-vibration (shifting between vibration

and non-vibration mode with button after power

on).

Press button about 2 second to power off the

detector with 1 second of buzzer and LED

alight 1 second.

Stop

using probe

Stop

using

motor

IV. Indication for low electricity of battery

Indication for low electricity of battery When battery voltage is

lower than 1.75V, LED will flicker 5 times slowly after power

on, and buzzer, if any signal, may sound faintly, and motor

vibrates weakly. Please replace battery immediately for the

test accuracy.

V. Battery replacement

Battery: 2 1.5V AAA×

(1). with one hand holding body, and thumb detector

of detectorother hand pressing the control position of

head and extending it backward.

(2). Please take out the upper cover of according

to the direction as shown in the picture, replace the battery.

(See the following picture)

detector

Periodically wipe the case with a dry cloth do not use

abrasives or solvents.

Cleaning

This operating manual is subject to change without notice.

*END*

P/N:110401103945X

MAY.2018 REV. 3

Produkt Specifikationer

Mærke:	Uni-T
Kategori:	Måleudstyr
Model:	UT12C

Har du brug for hjælp?

Hvis du har brug for hjælp til Uni-T UT12C stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måleudstyr Uni-T Manualer

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

1 April 2025

1 April 2025

1 April 2025

1 April 2025

1 April 2025

Kern KIP 3000V20LM Manual

1 April 2025

Kern ORA 2PB Manual

1 April 2025

Kern KFU 1500V20M Manual

1 April 2025

Kern ORA 90BE Manual

1 April 2025

Kern ORA 4AA Manual

1 April 2025