Uni-T UT330THC Manual

Uni-T Måleudstyr UT330THC

Læs gratis den danske manual til Uni-T UT330THC (1 sider) i kategorien Måleudstyr. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Uni-T UT330THC, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
P/N:110401112104X
UT330T/UT330TH/UT330THC
USB Datalogger
Introduction
Accessories
Safety information
Check if the logger is damaged before use.
Replace the battery when the logger displays “ ”.
If the logger is found abnormal, please stop using and contact your seller.
Do not use the logger near explosive gas, volatile gas, corrosive gas, vapor and powder.
Do not charge the battery.
3.0V CR2032 battery is recommended.
Install the battery according to its polarity.
Take out the battery if the logger is not used for a long time.
Description
Structure (Figure 1)
No.
Figure 1
Description Description
No.No.
Figure 2
Display (Figure 2)
The USB datalogger (Hereinafter referred to as “logger”) is a low power consumption, high-accuracy temperature &
humidity device. It has the characteristics of high accuracy, large storage capacity, auto save, USB data transmission,
time display and PDF export. It can meet the requirements of various measurements and long-term temperature and
humidity recording, and can be used in food processing, cold chain transportation, warehousing and other fields.
UT330T is designed with IP65 dust/water protection. UT330THC can be connected to an Android smartphone or
computer via the Type-C interface to analyze and export data in the smartphone APP or PC software.
USB cover
Indicator (Green light: logging, red light: alarm)
Display screen
Stop/switch humidity and temperature(UT330TH/UT330THC)
Start/select
Holder
Air vent (UT330TH/UT330THC)
Start
Maximum value
Stop
Minimum value
Marking
Circulatory
Mean kinetic temperature
Number of sets
Temperature unit
Low battery
Humidity unit
Temperature & humidity display area
Time display area
Set a fixed time/delay
Alarm due to abnormal logging
Setting
USB communication
Download the instruction and PC software according to the attached file, then, install the software step by step.
Insert the logger into USB port of PC, the main interface of logger will display “USB”. After the computer identifies
the USB, open the software to set parameters and analyze the data. (Figure 3).
Open the computer software to browse and analyze data. As for how to use the software, users can click the help
option on the operation interface to find “software manual”.
Parameter configuration
The computer identifies the logger model automatically.
°C or °F.
The generated report language can be set to English or Chinese.
Users can set the ID, the range is 0~255.
Factory number.
Users can add descriptions. The description will show in the generated PDF and
should be less than 50 words.
The product uses the UTC time zone, which can be set according to the local time zone.
Obtain PC time in real time.
Obtain the time when the device is connected. Check "Update" and click "Write",
the logger will synchronize with the PC time.
Users can select Single/Accumulate alarm mode.
Users can set the alarm threshold. The low temperature (low humidity) must be
smaller than the high temperature (high humidity).
The delay time used to determine the alarm state (0s to 10h)
Model
Unit
Language
ID
SN
Description
UTC/Time zone
PC time
Device time
Mode
Threshold
Delay
Linear temperature and humidity adjustment -6.0°C(RH%)~6.0°C(RH%)
Normal/Circulatory
10 seconds to 24 hours.
Start logging after the delay time. 0 to 240 minutes.
Press the button to start, start immediately through the software, start at a fixed time.
Choose if press the button to stop.prevent recording stop resulting from misoperation.
Write parameters to the logger.
Read logger parameters into the computer software.
Close the interface.
Temperature and
humidity Adjusting
Recording mode
Sampling interval
Sampling delay
Start with
Stop with key
Write
Read
Close
Figure 3 (Setting Interface of the PC Software)
Logger(with holder)……..………....1 piece
User manual……………………..…1 piece
Battery………………………………1 piece
Screw………………………………..2 pieces
No alarm
Lower value of alarm
Upper value of alarm
Operations
Starting the logger
There are three starting modes:
1.Press the button to start the logger
2.Start logging through the software
Battery Cover Opened Rib
8
8

Produkt Specifikationer

Mærke: Uni-T
Kategori: Måleudstyr
Model: UT330THC

Har du brug for hjælp?

Hvis du har brug for hjælp til Uni-T UT330THC stil et spørgsmål nedenfor, og andre brugere vil svare dig


Måleudstyr Uni-T Manualer

Uni-T

Uni-T UT220 Manual

3 April 2025
Uni-T

Uni-T UT681C Manual

3 April 2025
Uni-T

Uni-T UT216C Manual

3 April 2025
Uni-T

Uni-T UT611 Manual

3 April 2025
Uni-T

Uni-T UT210D Manual

3 April 2025
Uni-T

Uni-T UT210C Manual

3 April 2025
Uni-T

Uni-T UT210B Manual

3 April 2025
Uni-T

Uni-T UT682 Manual

3 April 2025
Uni-T

Uni-T UT275 Manual

3 April 2025
Uni-T

Uni-T UT08A Manual

3 April 2025

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

Kern

Kern ORA 6HB Manual

1 April 2025
Kern

Kern ORA 3AB Manual

1 April 2025
Kern

Kern ORA 10BA Manual

1 April 2025
Kern

Kern ORA 3HB Manual

1 April 2025
Kern

Kern ORA 1UB Manual

1 April 2025
Kern

Kern KIP 3000V20LM Manual

1 April 2025
Kern

Kern ORA 2PB Manual

1 April 2025
Kern

Kern KFU 1500V20M Manual

1 April 2025
Kern

Kern ORA 90BE Manual

1 April 2025
Kern

Kern ORA 4AA Manual

1 April 2025