Uni-T UT332 Manual

Uni-T Måleudstyr UT332

Læs gratis den danske manual til Uni-T UT332 (2 sider) i kategorien Måleudstyr. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Uni-T UT332, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

I. Overview

UT330 Series Digital Hygro-Thermometers (hereafter referred to as “ the Meter”)

adopts highly-precise hygro-thermo sensor and super-low power consumption

micro-processor in its design,featuring high accuracy, manual and auto storage,

USB data transfer, suitable time display, etc, which cover various demand

for high-accuracy measurements and long-time hygro-thermo monitoring.

II. Unpacking Inspection

III. Safety Information

Operating Manual 1 pc

Warranty Card 1 pc

Battery 4 pcs

Disc 1 pc

USB Data Cable 1 pc

Do not clean the sensor located at top of the Meter. Turn to close the

protective sensor cover when not in use. To avoid damage to the device,

please use with care.

Before using the Meter inspect the case. Do not use the Meter if it appears

damaged. Look for cracks or missing plastic. Pay

insulation around the connectors.

Replace the batteries as soon as the battery indicator (

) appears. The

of false readings can lead to personal injury.

Do not use the Meter if it operates abnormally. Protection may be

When in doubt, have the Meter serviced.

Do not operate the Meter around explosive gas, vapor, or dust.

Warning

A warning identified conditions and actions that pose hazards to the user. To

avoid

electrical shock or personal injury, follow these guidelines:

When servicing the Meter, use only specified replacement parts.

Do not use the Meter with any part of the case or cover removed.

Never charge the battery;

Use the approved alkaline battery

(AAA 1.5V) only;

Pay attention to “+” and “-” marks

when installing the batteries.

Close the sensor cover and remove

the batteries if the instrument is not

used for a long time.

IV. Meter Description

Meter Structure(See Figure1)

Figure 1

Description

Protective cover of sensor (turn to open or close).

Display screen.

Turn on/off the power save mode.

Press to display Max/Min value among current readings. Long press to exit

the function(also used ▲ button).

Press to save data. It is used together with ▼▲. See "Using the Meter --

Store and Recall Data" for details.

Turn on/Turn off the background light.

Press to freeze the displayed readings. Press again to exit the function.(also

used as ▼ button).

Press to view data. It is used together with ▼▲ buttons. See "Using the

Meter -- Store and Recall Data" for details.

Dew-point temperature selection key (also used as confirm button).

To set the meter. It is used together with ▼▲ buttons. See "Setting the

Meter" for details.

particular attention to

the

possibility

Display Screen (See Figure 2)

Figure 2

Description

Max/Min function indicator

Battery indicator

Description

Time display zone

Temperature display zone

Display of holding time

Online indicator

Humidity unit

Indicator of setup mode

Temperature unit

Indicator of time format

Backlight indicator

Data recall/store indicator

Dew-point temperature

Humidity display zone

Power save mode

V. Setting the Meter

SETUP Options

Press SETUP button to enter into setting mode, “SET” flashes on LCD, continue

to pressthe button to step through and save the following setup options and exit

the mode.

Performing the Setups

1. Setting Temperature Unit

Press SETUP to access Temperature Unit setup mode, “Unt” shows on LCD.

Press ▼(HOLD)/▲(Max/Min) to select ℃ or ℉ unit.

2. Setting Time Interval

Press SETUP to switch to time interval mode, “int” shows on LCD. Press▼▲ to

change the interval for automatic data storage. Long press ▼▲ to increment

the time quickly.

The interval can set up to 59:59 and down to 00:00(auto data storage disabled

at 00:00).

3. Setting Humidity Offset

Press SETUP to switch to humidity offset mode, “H-O” icon shows. Press ▼▲

to change the offset value that ranges within -6~+6.

4. Setting Temperature Offset

Press SETUP to switch to temperature offset mode, “t-o” icon shows. Press ▼

▲ to change the offset value that ranges within -6~+6.

5. Setting Dew Point Offset

Press SETUP to switch to dew point offset mode, “d-o” icon shows. Press ▼▲

to change the offset value that ranges within -6~+6.

6. Setting Sleep Mode

Press SETUP to switch to sleep offset mode, “SLP” icon shows. Press ▼▲ to

set up sleep time(5~60mins). Long press ▼▲ to increase the time quickly;

When the set time is ＜5mins, “OFF” icon shows and sleep function is disabled.

impaired.

Produkt Specifikationer

Mærke:	Uni-T
Kategori:	Måleudstyr
Model:	UT332

Har du brug for hjælp?

Hvis du har brug for hjælp til Uni-T UT332 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Måleudstyr Uni-T Manualer

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

3 April 2025

Måleudstyr Manualer

Nyeste Måleudstyr Manualer

1 April 2025

1 April 2025

1 April 2025

1 April 2025

1 April 2025

Kern KIP 3000V20LM Manual

1 April 2025

Kern ORA 2PB Manual

1 April 2025

Kern KFU 1500V20M Manual

1 April 2025

Kern ORA 90BE Manual

1 April 2025

Kern ORA 4AA Manual

1 April 2025