Velleman KSR2 Manual


Læs gratis den danske manual til Velleman KSR2 (19 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Velleman KSR2, eller vil du spørge andre brugere om produktet?

Side 1/19
KSR2 VELLEMAN 1
KSR2 – ROBOT FROG
1. Introduction & Characteristics
Thank you for buying the KSR2 ! Read this manual carefully before bringing the device into use.
The KSR2 is a robot frog that uses a microphone as a detector. The car changes directions when the sensor detects
noise or when the car hits an object.
The KSR2 requires one 9V DC battery (not included) for the electronic parts and 2 AA-batteries of 1.5V for the
mechanical parts (not included).
Apart from the batteries, you will also need a length of solder wire, a pair of long-nose pliers, a soldering iron, a
diagonal cutter, a screwdriver and a soldering iron stand with sponge.
2. Electronic Parts List
1. resistor : 2 x 100 (brown/black/brown/gold)
2 x 4.7K (yellow/violet/red/gold)
1 x 10K (brown/black/orange/gold)
1 x 22K (red/red/orange/gold)
5 x 33K (orange/orange/orange/gold)
2 x 2.7M (red/violet/green/gold)
2. battery snap with wires 15cm (1 x)
3. battery holder with wires 8cm (1 x)
4. transistor : 2 x type 1815 (or C945) and 2 x type 8050
5. IC : 1 x type 4017 and 1 x type 406P
6. ceramic capacitor 47P (1 x)
7. electrolytic capacitor 1uf (2 x)
8. diode IN 4148 (6 x)
9. mylar capacitor 103 (1 x)
10. microphone Ø10mm (1 x)
11. variable resistor 200K (1 x)
12. slide switch (1 x)
13. Ø1.3mm pin (8 x)
14. connector with wire 15cm : 1 x yellow, 1 x blue, 1 x orange, 1 x green
15. PCB (1 x)
3. Mechanical Parts List
Part n° Quant. Description Part n° Quant. Description
1 2 gearbox 15 1 battery holder (9V-battery)
2 2 motor DC3V 16 2 hex post (M3 x 25mm)
3 2 metal shaft (2 x 40mm) 17 1 right front wheel bracket
4
2 metal shaft (3 x 52mm) 18
1 left front wheel bracket
5 2 pinion gear 10T (white) 19 1 nylon post (Ø3 x 3mm)
6 20 2 face gear 36T/14T (white) 1 nylon nut
7 21 2 gear 36T/0T (white) 2 nut M3
8
2 gear 36T/14T (red)
22 5 nut M2
9 2 gear 36T/14T (green) 23 2 washer (3.2 x 10 x 0.5mm)
10 4 nylon pad (5.6 x 4.8 x 1.95mm) 24 1 self-tapping screw (2 x 4mm)
11 25 2 rear wheel (Ø32 x 3.5mm) 6 screw (M3 x 8mm)
Fig. 1
KSR2 VELLEMAN 2
12 2 rubber tyre 26 1 screw (M3 x 16mm)
13 27 1 front wheel (Ø20mm) 5 screw (M2 x 10mm)
14 28 1 rubber ring (Ø15 x 2.5mm) 1 wooden plate (included)
4. Assembly
a) PCB Assembly
Start the assembly by mounting the resistors. The names of all components have been printed on the PCB. Consult
the table below :
Part ID Description. Colour Code Quantity
R10/13 100 brown/black/brown/gold 2
R8/11 4.7K yellow/violet/red/gold 2
R1 10K brown/black/orange/gold 1
R7 22K red/red/orange/gold 1
R2/4/6/9/12 33K orange/orange/orange/gold 5
R3/5 2.7M red/violet/green/gold 2
Mount the diodes, capacitors, transistors, the variable resistor, the IC’s, the slide switch and the pins next. Consult
the table below :
Part ID Description Quant.
D1/2/3/4/5/6 diodes IN 4148 6
C2 ceramic capacitor 47P 1
C1 mylar capacitor 103 1
C3/4 electrolytic capacitor 1uf 2
Fig. 2


Produkt Specifikationer

Mærke: Velleman
Kategori: Ikke kategoriseret
Model: KSR2

Har du brug for hjælp?

Hvis du har brug for hjælp til Velleman KSR2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Velleman Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer