Ventev TW-COLOMOUNT-2 Manual

Ventev Ikke kategoriseret TW-COLOMOUNT-2

Læs gratis den danske manual til Ventev TW-COLOMOUNT-2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Ventev TW-COLOMOUNT-2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Mounting Instructions

Note: The Co-Locating Mount can be mounted on any at surface including, but not limited to, walls, ceilings, and I-beams. Mounting hardware

is not included with this product. User should identify the mounting surface and then purchase the appropriate mounting hardware.

Caution: Ensure the mounting surface will support the fully assembled unit’s weight including the mount itself, the access point, and the antenna.

Figure 2

2. Detach the circular Surface Mounting Plate from the Access Point Mounting Plate by

unscrewing the Chase Nipple nut. Set aside the Chase Nipple nut for later use. Retain the

Chase Nipple within the Surface Mounting Plate.

Figure 3

3. Set aside the combined Access Point Mounting Plate/Antenna Mounting Tray for later use.

Figure 4

4. Place the Surface Mounting Plate over the desired mounting location, with the four Surface

Mounting Stand-Os touching the mounting surface.

5. Pull the RJ-45 cable through the Chase Nipple and allow it to hang loose.

6. Insert four screws or bolts into the four Surface Mounting Holes. Tighten the screws/bolts

until the Surface Mounting Plate is secure against the mounting surface.

Figure 2

Figure 4

Figure 3

Surface

Mounting

Stand-os

Dry Wall Mounting:

- 4x Wall Anchors

- 4x Dry Wall Screws that t the holes shown in Figure 2.

Wood Wall Mounting:

- 4x Wood Screws that t the holes shown in Figure 2.

- 4x Locking Washers

Metal Surface Mounting

- 4x Metal Screws that t the holes shown in Figure 2.

- 4x Flat Washers

- 4x Locking Washers

Recommended Hardware:

Locking Screws

Antenna

Mounting

Tray

Cable

Management Clips

Swing Arm

Locking Tab

Thumb

Screws

TToward Antenna

Coverage Area

TToward Mounting

Surface

Access Point

Mounting Plate

Surface Mounting

Plate

4x Surface

Mounting Holes

Chase Nipple

Chase

Nipple Nut

Chase

Nipple

Threads

Surface

Mounting

Plate

Figure 1

1. Major parts of the Dual Axis Co-Locating Mount. Refer to it as required for the remaining steps.

Figure 5

7. Position the combined Access Point Mounting Plate/Antenna Mounting Tray so that

the threaded Chase Nipple inserts into the Access Point Mounting Plate’s hole. Thread

the Chase Nipple nut onto the Chase Nipple and nger tighten. The mated assembly

should look like Figure 5.

Figure 6

8. Locate the four Access Point Mounting Slots (circled) in the Access Point Mounting Plate.

9. Insert the access point’s rubber mounting feet into the Access Point Mounting Slots.

Slide the mounting feet inside the Mounting Slots until the access point locks into place

with an audible snap.

10. Recommended step for securing the access point: Secure the access point to the Access

Point Mounting Plate through the locking tab. The most common method is to thread a

zip-tie through the Mounting Plate’s locking tab and the access point’s adjacent locking

tab and tighten the zip-tie.

11. Insert the RJ-45 cable into Access Point’s RJ-45 port.

Figure 7

12. Remove the nuts and washers from Antenna mounting bolts located at rear of the antenna.

Push the antenna’s mounting bolts through the holes in the Antenna Mounting Tray.

13. Re-attach antenna washers and nuts and tighten them to hold antenna securely against

Mounting Tray.

14. Run antenna cables through cable management clips and attach cable connectors to the

Access Point.

15. Optional steps for positioning antenna:

a. The Chase Nipple nut is still only nger tight. Rotate the combined Access Point

Mounting Plate/Antenna Mounting Tray until it is in the desired position. Tighten the

Chase Nipple Nut so further rotation is impossible.

b. Loosen the Antenna Mounting Tray’s thumb screws and locking screws. Rotate

the Antenna Mounting Tray to achieve the desired antenna position. Tighten all screws.

Chase

Nipple Nut

Chase Nipple

Threads

Figure 5

Figure 6

Figure 7

Produkt Specifikationer

Mærke:	Ventev
Kategori:	Ikke kategoriseret
Model:	TW-COLOMOUNT-2
Bredde:	276 mm
Dybde:	259 mm
Højde:	155 mm
Vægt:	1701 g
Produktfarve:	Hvid
Produkttype:	WLAN-adgangspunktmontering
Kapabilitet:	Cisco 2802e, 3802e