Whirlpool ADP 6949 Eco Manual

Whirlpool Opvaskemaskine ADP 6949 Eco

Læs gratis den danske manual til Whirlpool ADP 6949 Eco (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 33 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 17 anmeldelser. Har du et spørgsmål om Whirlpool ADP 6949 Eco, eller vil du spørge andre brugere om produktet?

Side 1/8
GB -1-
Chart
START
DELAY
option
MULTI
ZONE
option
ANTI-
BACTERIAL
RINSE
option
ON/OFF
BUTTON
PROGRAMME
SELECTION
BUTTON
(See Table of
programmes)
START BUTTON
The indicator lights up during operation, flashes when a fault occurs, and goes off
at the end of the programme.
START BUTTON RESET FUNCTION:
Press this button for at least 2 seconds; the selected programme and options will
be cancelled. Main failure displays (repeated flashing of the START indicator lamp)
can be cancelled by RESETTING. Detailed instructions are given in chapter
“What to do if...”.
(see at right for options description)
1) Programme data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary
depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance’s automatic calibration system
.
2) Reference programme for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the
EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Table of programmes
Detergent
Consumption
PProgrammes Available
options Loading instructions Litres kWh Minutes 1)
1Aqua Steam 40-70°C
Delay
Multizone
Antibacterial
rinse
Normally or heavily soiled crockery,
including pots and pans. Thanks to
steam action, soaking or hand pre-
treatment is no longer needed. In
addition hygiene is ensured due to the
high temperature steam.
X 7-17 0.99-1.75 65-220
2Pre-Wash cold Delay
Multizone Crockery to be washed later. 4.0 0.03 14
3Glasses 40°C Delay
Multizone
Light soiling, for example glasses
and cups. X 10.0 0.85 100
4Quickwash 40°C Delay
Multizone
Lightly soiled crockery, with no
dried-on food. * Use of tablets
not recommended.
X*10.0 0.65 30
5Bio 2) 50°C
Delay
Multizone
Antibacterial
rinse
Normally soiled crockery. X 13.0 0.93 185
6Overnight 55°C Delay
Multizone
Normally soiled crockery, gentle
and quiet thanks to the lower spray
pressure (39dbA).
X 13.0 1.20 290
5019 396 01747
ADP 6949 Eco
DELAYED START
BUTTON
Press the button (repeatedly)
to delay the start of the
programme. Adjustable from 1
to 24 hours. With each press of
the button, the delayed start
indicator increases by one hour
and after 24 restarts from 00.
Then press the START button.
The dishwasher will start after
the set time.
HALF LOAD/MULTIZONE
Allows you to choose the
washing zones. Press this button
to select the wash zones:
both racks
only upper rack
only lower rack
ANTIBACTERIAL RINSE 3)
This function activates an
antibacterial rinse at the end of
the wash cycle, guaranteeing a
further reduction of bacteria.
Press the button to activate or
deactivate the function. This
function can be used with
those programmes marked
with the relative description in
table. The dishwasher door
must be kept shut for the
entire duration of the
programme in order to
guarantee reduction of
bacteria. If the door is opened
the indicator lamp starts
flashing.
RINSE AID INDICATOR
When lit, the rinse aid dispenser needs
to be refilled.
SALT INDICATOR
When lit, the salt reservoir
needs to be refilled.
FAULT INDICATION AND WASH TIME DISPLAY
In normal operation it indicates the remaining time (h:mm),
whereas with “Delayed start” selected it indicates the time
remaining until programme start (hh).
If “F..” appears on the display, see chapter “What to do if...”.
Options and display description
BEFORE USING THE APPLIANCE FOR THE
FIRST TIME CAREFULLY READ THIS QUICK
REFERENCE GUIDE AND THE INSTALLATION
INSTRUCTIONS! THE GUARANTEE IS NOT
APPLICABLE IF FAULTS ARE CAUSED BY
INCORRECT USE OF THE APPLIANCE.
Quick reference guide
GB -2-
First time use
5 7 86
2
3
S
E
L
1
4
10
9
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
In order to always ensure the best cleaning
results, you NEED to set:
DETERGENT type and WATER HARDNESS.
1. Select 3rd programme
(see Table of programmes
- page 1)
2. Press START button
for 7 seconds
3a. Check your
detergent type...
3b....and set it on your dishwasher
using the START button
(as per table below)
4. Remember to use salt and rinse
aid when needed (as indicated
below)
5. Switch off and switch on
again to save setting
Detergent
types
Dishwasher models
model without
display model with display
Powder or gel
(factory setting) no symbol add rinse aidadd salt
Tablet 2 in 1 add salt
Tablet 3 in 1
Tablet All in 1
For models without “detergent type” option, the salt and rinse aid indicators will be lit when tablets are used.
3h 6h 9h
rinse aid
salt rinse aid
1. Ask your water supply company what the water hardness is... 2. ...enter this value on your
dishwasher
Suggestions for detergent use
German
degrees °dH French
degrees °fH English
degrees °eH Water
hardness
Dishwasher
with display:
insert value in
the display
Dishwasher
without
display: count
START button
led flashes
Gel or Powder
(rinse aid and
salt)
Tablets
0 - 5 0 - 9 0 - 6.3 Soft 1x1
go to step 1
(see “Daily
check”)
if extra salt is
needed go to
step 1
(see “Daily
check”)
6 - 10 10 - 18 7 - 12.6 Medium 2 2x
11 - 15 19 - 27 13.3 - 18.9 Average 3 3x
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 4x
22 - 28 38 - 50 26.6 - 35 Hard 5 5x
29 - 35 51 - 63 35.7 - 44.1 Very hard 6 6x
36 - 60 64 - 107 44.8 - 74.9 Extremely
hard 7 7x
How to set water hardness
* only before the first wash or if the
water hardness has been changed
Switch on the appliance
- Select the 2nd programme “P2” - consult the table of programmes.
- Press the START button for at least 5 seconds until the START indicator lamp flashes.
- The water hardness setting is shown on the display (if present) or the START button flashes.
- With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again.
- The appliance must be switched off to memorise the new setting.
Even if you use tablets which include salt,
you must still add salt since such
detergents are not effective enough at
softening hard water.
Water hardness level is factory set for
medium hard water (a number “4” is
shown on the display or the START
indicator lamp flashes 4 times).
How to set detergent type: powder/gel/tablet (if option is available)


Produkt Specifikationer

Mærke: Whirlpool
Kategori: Opvaskemaskine
Model: ADP 6949 Eco

Har du brug for hjælp?

Hvis du har brug for hjælp til Whirlpool ADP 6949 Eco stil et spørgsmål nedenfor, og andre brugere vil svare dig