Whirlpool W10250638 Manual

Whirlpool Køleskab W10250638

Læs gratis den danske manual til Whirlpool W10250638 (6 sider) i kategorien Køleskab. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Whirlpool W10250638, eller vil du spørge andre brugere om produktet?

Side 1/6
INSTRUCTION SHEET FOR BUILT-IN REFRIGERATOR
HANDLE ACCESSORY
BEFORE YOU BEGIN: The handle and handle mounting hardware must be installed before installing the custom panel. A qualified
cabinetmaker must perform the installation.
IMPORTANT:
This kit is designed to be used only with wood panels.
To avoid damage, lift the door and drawer panel(s) by the
edges.
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
PARTS SUPPLIED:
*Numbers may vary depending on refrigerator model and handle
type.
Install the Refrigerator Handle(s)
IMPORTANT: For model specific hole location and the spacing
requirements for mounting the handles onto the panels, see
Figure 1 and the following Refrigerator Door table.
1. Measure from the bottom of the custom panel and mark your
first hole location as shown in Figure 1 and the Refrigerator
Door table.
Figure 1 - Refrigerator Door
W10248266A
Cordless drill
⁵⁄₁₆" Socket driver
³⁄₃" Allen wrench
Drill bits
Flat-blade screwdriver
Tape measure
Pencil
Handle - freezer drawer
Handle - refrigerator
door*
Studs - handle
mounting*
Screws - #10-24 x 1"
hex washer head*
Refrigerator Door
Handle Type A B
Bottom Mount
Classic
Euro-Style
11 ³⁄₁₆"
(28.42 cm)
30"
(76.20 cm)
Euro-Style 10 ³⁄₄"
(27.31 cm)
30 ³⁄₄"
(78.11 cm)
Pro 10 ³⁄"
(27.31 cm)
30 ³⁄₄"
(78.11 cm)
French Door
Bottom Mount
Classic
Euro-Style
11 ³⁄₁₆"
(28.42 cm)
30"
(76.20 cm)
Euro-Style 10 ³⁄₄"
(27.31 cm)
30 ³⁄₄"
(78.11 cm)
Pro 10 ³⁄"
(27.31 cm)
30 ³⁄₄"
(78.11 cm)
Side by Side
Classic
Euro-Style
See Figure 2
Side by Side Euro
Euro-Style 19 ³¹⁄₃₂"
(50.72 cm)
43 ¹⁄₈"
(109.54 cm)
Pro 19 ³¹⁄₃₂"
(50.72 cm)
43 ¹⁄₈"
(109.54 cm)
Handle
Mounting
Studs
Refrigerator
Compartment
Handle
Custom Refrigerator
Compartment Panel
Setscrews
#10-24 x 1" Screws
A
B
Figure 2 - Side by Side Classic Euro-Style
NOTE: Measurements from the side edge of the door will
depend on specific application.
2. Drill a ³⁄₁₆" (4.76 mm) hole at that location, then measure up
from the bottom hole to determine the location of the second
hole. Countersink both holes on the inside of the panel, ¹⁄₄"
(6.35 mm) deep and ⁵⁄₈" (1.58 cm) diameter for screw head
clearance.
3. Install two mounting studs to the custom panel using the
screws provided. Make sure the head of the screw is flush
with the panel.
4. Install handle to handle mounting studs and tighten the
setscrews. Some adjustments of the handle mounting studs
may be required to allow the handle to fit over both mounting
studs.
NOTE: For products with one refrigerator door, the setscrew
should face the hinge side of the door. For products with two
refrigerator doors, the setscrews should face the center of the
product.
5. If you have two refrigerator doors or a side-by-side freezer
door, repeat steps 1 through 4 to install the other handle.
Install the Freezer Drawer Handle
IMPORTANT: For model specific hole location and the spacing
requirements for mounting the handles onto the panels, see
Figure 3 and the following Freezer Drawer table.
1. Measure from the side of the custom panel and mark your
first hole location as shown in Figure 3 and the Freezer
Drawer table.
Figure 3 - Freezer Drawer
NOTE: Measurements from the top edge of the door will
depend on specific application.
2. Drill a ³⁄₁₆" (4.76 mm) hole at that location, then measure from
that hole over to the second hole. Countersink both holes on
the inside of the panel, ¹⁄₄" (6.35 mm) deep and ⁵⁄₈" (1.58 cm)
diameter for screw head clearance.
3. Install two mounting studs to the custom panel using the
screws provided. Make sure the head of the screw is flush
with the panel.
4. Install handle to handle mounting studs and tighten the
setscrews. Some adjustments of the handle mounting studs
may be required to allow the handle to fit over both mounting
studs.
NOTE: The freezer handle setscrews should face down.
#10-24 x 1" Screws
60 "¹⁄₂
(153.7 cm)
26 "¹⁄₂
(67.3 cm)
Handle mounting stud
46 "¹⁄₂
(118.1 cm)
6 "⁄₈
(17.5 cm)
Setscrews
Freezer Drawer
Handle Type A B
Bottom Mount
Classic
Euro-Style
5 ¹⁄₄"
(13.34 cm)
24 ³⁄₄"
(62.87 cm)
Euro-Style 5 ²⁷⁄₃₂"
(14.84 cm)
23 ⁹⁄₁₆"
(59.85 cm)
Pro 5 ²⁷⁄₃₂"
(14.84 cm)
23 ⁹⁄₁₆"
(59.85 cm)
French Door
Bottom Mount
Classic
Euro-Style
8 ²⁷⁄₃₂"
(22.46 cm)
23 ⁹⁄₁₆"
(59.85 cm)
Euro-Style 5 ¹⁄₄"
(13.34 cm)
30 ³⁄₄"
(78.11 cm)
Pro 5 ¹⁄₄"
(13.34 cm)
30 ³⁄₄"
(78.11 cm)
Handle
Mounting Studs
Freezer
Compartment
Handle
Custom Freezer
Compartment Panel
#10-24 x 1" Screws
B
A
Setscrews


Produkt Specifikationer

Mærke: Whirlpool
Kategori: Køleskab
Model: W10250638

Har du brug for hjælp?

Hvis du har brug for hjælp til Whirlpool W10250638 stil et spørgsmål nedenfor, og andre brugere vil svare dig