Zodiac TP500 Manual

Zodiac Ikke kategoriseret TP500

Læs gratis den danske manual til Zodiac TP500 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Zodiac TP500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1-4

FUNCTION

INSTALLATION

THIS FILTER OPERATES UNDER HIGH PRESSURE. WHEN ANY PART OF THE CIRCULATING

SYSTEM (e.g., CLAMP, PUMP, FILTER, VALVES, ETC.) IS SERVICED, AIR CAN ENTER THE

SYSTEM AND BECOME PRESSURIZED . PRESSURIZED AIR CAN CAUSE THE LID OR VALVE TO

BE BLOWN OFF WHICH CAN RESULT IN SEVERE INJURY, DEATH, OR PROPERTY DAMAGE

TURN PUMP OFF BEFORE CHANGING VALVE POSITION.

WARNING

4-4

TO PREVENT DAMAGE TO THE PUMP AND FOR PROPER OPERATION OF THE SYSTEM,

CLEAN PUMP STRAINER AND SKIMMER BASKETS REGULARLY.

DO NOT UNSCREW SCREWS OF FLANGE CLAMP WHILE PUMP IS RUNNING.

ASFI09051703

FUNCTIONS OF VALVE POSITIONS

WASTE

FILTER

BACKWASH RINSE

WASTE

RECIRCULATE

CLOSED

WASTE WASTE

WASTE WASTE WASTE

IN FLOW OUT FLOW IN FLOW OUT FLOW IN FLOW OUT FLOW

GENERAL

SERVICING VALVE( Stop pump,close gate valve in suction&discharge before proceeding):

a. Set handle in filter position. b. Remove cover screws. c. Lift cover and key assembly out.

TO ASSEMBLE:

1. Place valve key so that wedge opening is at TOP port (handle in Filter psn.). Flat edge of cover screw lug should align with

flat edge of body screw lug.

2. Position cover o’ring.

3. Secure assembly to body with cover screws. Tighten cover screws evenly and alternately. Do not over-tighten.

The filter uses special filter sand to remove dirt particles from pool water. The filter sand is loaded into the filter tank and functions as

a permanent dirt removing media. When the control valve is in the FILTER position, the pool water which contains suspended dirt

particles, is pumped through your piping system and is automatically directed by the patented filter control valve to the top of the filter

tank. As the pool water is pumped through the filter, dirt particles are trapped by the sand bed, and filtered out. The cleaned pool water is

returned from the bottom of the filter tank, through the control valve and back to the pool through the piping system. This entire sequence

is continuous and automatic. It provides for total recirculation of pool water through your filter and piping system.

After a period of time, the accumulated dirt in the filter causes a resistance to flow, and the flow diminishes. This means it is time to

clean your filter. With the control valve in the BACKWASH position, the water flow is automatically reversed through the filter so that it

is directed to the bottom of the tank, up through the sand, flushing the previously trapped dirt and debris out the waste line. Once the filter

is back-washed of dirt, set control valve to RINSE position and run pump for about 1/2 to 1 minute, and then set the control valve in the

FILTER position, to resume normal filtering.

NOTE: Turn pump off before changing valve position.

TITAN SERIES SAND FILTER

Model : TP500, TP650, TP700

(Link by Clamp type Valves)

Only simple tools (screwdriver and wrenches), plus pipe sealant for plastic adapters, are required to install and

service the filter.

1. The filter should be placed on a level concrete slab, very firm ground, or equivalent. The filter should be placed

2. Loading the sand media. Filter sand media is loaded through the top opening of the filter.

a. Loosen the flange clamp and remove filter control valve (if previously installed).

b. Cap internal pipe with plastic cap to prevent sand from entering it.

c. We recommend filling the tank approximately 1/2 way with water to provide a cushion effect when the filter

d. Carefully pour in correct amount and grade of filter sand. (Be sure center pipe remains centered in opening.)

internal pipe.

in the right position so that the piping connections, control valve are convenient and accessible for operation and service.

sand is poured in. This helps protect the under-drain laterals from excessive shock.

Sand surface should be leveled and should come to about the middle of the filter tank. Remove plastic cap from

Valve Position Function

FILTER

BACKWASH

RINSE

WASTE

RECIRCULATE

CLOSED

Normal Filtration and Vacuuming

Cleaning Filter by reversing the flow

Used after backwash to flush dirt from valve

By-passes filter, used for vacuuming to waste or lowering water level

By-passes filter for circulating water to pool

Shuts off all flow to filter or pool

Produkt Specifikationer

Mærke:	Zodiac
Kategori:	Ikke kategoriseret
Model:	TP500

Har du brug for hjælp?

Hvis du har brug for hjælp til Zodiac TP500 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Zodiac Manualer

Zodiac eXPERT Manual

5 Oktober 2025

Zodiac Chlor Expert Manual

5 Oktober 2025

Zodiac GenSalt OT Manual

5 Oktober 2025

Zodiac GenPH Manual

4 Oktober 2025

Zodiac Heat Line Manual

4 Oktober 2025

Zodiac GenChlor Manual

4 Oktober 2025

Zodiac eXO iQ Dual Link Manual

4 Oktober 2025

Zodiac Power Force Manual

2 Oktober 2025

Zodiac CAE Ducted Manual

1 Oktober 2025

Zodiac eXPERT pH Manual

1 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Growatt MIN2.5-6KTL-XH2 Manual

15 December 2025

Bosch SBH6YCX02F Manual

15 December 2025

Eurosound HDBT-BYOD-EX1-P Manual

15 December 2025

Milwaukee MX Fuel MXF002 Manual

15 December 2025

JET JCT-3620A Manual

15 December 2025

California Faucets K30-102SQ Manual

15 December 2025

Tefal Aromati-Q 3-in-1 BG9108 Manual

15 December 2025

Godrej Vigiguard Tripod Manual

15 December 2025

Gladiator GAWB04HWJW Manual

15 December 2025

Kathrein UFO 110/4 Manual

15 December 2025