4ms Rotating Clock Divider Manual

4ms Ikke kategoriseret Rotating Clock Divider

Læs gratis den danske manual til 4ms Rotating Clock Divider (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om 4ms Rotating Clock Divider, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
Rotating Clock Divider
Eurorack Module User Manual (updated Sept 2015)
PCB version 1.2 (released November 2014)
Firmware version 1.1 (released April 2012)
4ms Pedals
Features
•Divide-by-1 to Divide-by-64, on 8 output jacks
•CV Rotate jack to shift divide-by amount on all jacks
•CV Reset to reset/re-sync all jacks
•Jumpers or optional break-out panel:
◦Select auto-reset
◦Select "Spread" mode
◦Select maximum divide-by amount (8/16/32/64)
◦Gate or Trigger outputs
◦Count-up or Count-down mode
•ISP header
◦Connects to in-circuit programmer such as AVR ISP MKII for reprogramming code
•Maximum input frequency 3kHz
•LED dimmer trimpot allows you to set a custom LED brightness
•Bus Clock support (slave only). Clock can be taken from the Gate pins on the power
header.
•5V Select jumper allows you to power the RCD from either the 12V rail or the 5V rail.
•4 HP Eurorack module
•5VSEL Jumper set to INT:
◦33mA maximum power draw from +12V rail
◦0mA max on the +5V rail
◦4mA maximum power draw on the -12V rail
•5VSEL Jumper set to EXT:
◦19mA maximum power draw on the +12V rail
◦14mA max on the +5V rail
◦4mA maximum power draw on the -12V rail
Jacks
•Clock Input (3.5V to 15V clock, rising edge triggered)
•CV Rotate (0V to +5V input)
•CV Reset (3.5V to 15V trigger)
•Divided Clock Outputs (8 jacks):
•Divide-by (1+R)
•Divide-by (2+R)
•Divide-by (3+R)
•Divide-by (4+R)
•Divide-by (5+R)
•Divide-by (6+R)
•Divide-by (7+R)
•Divide-by (8+R)
•..where R is the CV Rotation (0 to 63)
Breakout Header/jumpers
The breakout header on the back of the
PCB has spots for 6 jumper shunts which
enable/disable features and change the
operation of the RCD. You also can attach
an RCD Breakout module, which makes
changing settings convenient and
accessible.
If you don't have an RCD Breakout, you can
set the RCD to operate in a particular mode
by installing certain jumpers, and omitting
others.
Note: The bottom four pins of the breakout
header have been snipped off or have been
omitted at the factory.
Counting Up/Down:
Up/
Down
Mode
on Down counting
off Up counting
Trigger/Gate:
Trig/
Gate
Mode
on Gate
off Trigger
Auto-Reset:
Auto-
Reset
Jumper
Auto-reset amount
with Max-Divide-by range of...
8 16 32 64
on 16 32 64 128
off none none none none
Max Divide-by Range and Spread Mode:
Max-
Divide
Range
Jumpe
rs
Total
Rotatabl
e Divide-
by range
Default Divide-by amount on jacks with no voltage applied to CV Rotate jack
(tables 2-5)
(Applying CV to Rotate jack makes each output increase by 1)
See also Table 5 below
16 32 Spread off Spread on
on on 1 to 8 1, 2, 3, 4, 5, 6, 7, 8 1, 2, 3, 4, 6, 8, 12, 16
on off 1 to 16 9, 10, 11, 12, 13, 14, 15, 16 2, 4, 6, 8, 10, 12, 14, 16
off 1 to 32 17, 18, 19, 20, 21, 22, 23, 24 4, 8, 12, 16, 20, 24, 28, 32on
off off 1 to 64 33, 34, 35, 36, 37, 38, 39, 40 8, 16, 24, 32, 40, 48, 56, 64
Gate/Trigger Mode:
In Trigger mode, the jacks output a pulse width equal to that of the input clock (the pulse width is not multiplied
or divided proportionally to the jack's divide-by amount). This is the default method for pcb v1.0 and v1.0.1,
unless it has been upgraded to v1.0.2 or later firmware.In Gate mode, the width of the output pulses are 50% of
the total wave. For example, the /6 jack will stay ON for 3 clock pulses, and then turn OFF for 3 clock pulses. For
even numbered divisions (/2, /4, /6, /8, etc) the transitions happen on the input clock's rising edge.Point of
interest: In Gate mode, with odd-numbered divisions, the jack will turn ON on a rising edge of the input clock,
and then will turn OFF on a falling edge. For example, the /5 jack ought to stay on for 2.5 clock pulses, meaning
it should go OFF somewhere between the rising edge of clock pulses 2 and 3. Right in between these is the
falling edge of pulse number 2, so we can safely call it 2.5!
When in Gate mode, the difference between Up and down-counting is that the gates are inverted.

Produkt Specifikationer

Mærke: 4ms
Kategori: Ikke kategoriseret
Model: Rotating Clock Divider

Har du brug for hjælp?

Hvis du har brug for hjælp til 4ms Rotating Clock Divider stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret 4ms Manualer

4ms

4ms Listen Up Manual

1 Oktober 2024
4ms

4ms Buff Mult Manual

22 September 2024
4ms

4ms Catalyst Sequencer Manual

2 September 2024
4ms

4ms Looping Delay Manual

23 August 2024
4ms

4ms Sampler Manual

23 August 2024
4ms

4ms VCA Matrix Manual

15 August 2024
4ms

4ms Ensemble Oscillator Manual

11 August 2024
4ms

4ms Pod 34X Manual

2 August 2024
4ms

4ms Rotating Clock Divider Manual

31 Juli 2024
4ms

4ms QCD Expander Manual

26 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Simrad

Simrad Active Imaging HD (Thru-Hull) Manual

14 Juni 2025
Garritan

Garritan Harps Manual

14 Juni 2025
Marshall

Marshall CV-H20-HF Manual

14 Juni 2025
Aiphone

Aiphone IXW-MAA Manual

14 Juni 2025
Rival

Rival HM-743 Manual

14 Juni 2025
Lutec

Lutec Avony Manual

14 Juni 2025
Giordani

Giordani G-SAFE & PLAY Manual

14 Juni 2025
Gourmia

Gourmia GAF799 Manual

14 Juni 2025
Arendo

Arendo 307503 Manual

14 Juni 2025
Hughes & Kettner

Hughes & Kettner Tube 100 Manual

14 Juni 2025