AIC RSC-4H Manual

AIC Ikke kategoriseret RSC-4H

Læs nedenfor 📖 manual på dansk for AIC RSC-4H (57 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 42 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/57

Document Number: MAN-00404-A

RSC-4H

Rackmount Storage Chassis

User Manual

contents

CONTENTS

PREFACE ��i

SAFETY INSTRUCTIONS ��ii

Chapter 1� Prodcut Introduction ��1

1�1 Box Content ��1

1.2 Specications ��2

1�3 General Information ��3

Chapter 2� Hardware Installation ��6

2�1 Removing and Installing Top Cover ��6

2�2 Removing/Installing a Drive Tray ��7

2�3 Installing/ Removing a Hard Disk Drive ��8

2�4 Removing and Installing a PSU Module ��9

2�5 Removing and Installing a Fan Module ��10

2�6 Removing and Installing HDD Backplane ��11

2�7 Tool-less Blade Slide Installation Instruction ��12

Chapter 3� Hardware Instruction �� 19

3�1 HARDWARE DESIGN SPECIFICATION ��19

Chapter 4� HDD Blackplane Instruction �� 24

4.1 Expender rmware update through smart console port ��24

4.2 Update the expander rmware through in-band. ��37

4�3 12G expander EDFB setting ��41

4�4 Slot HDD power setting ��43

4�5 HDD BP thermal sensor temperature setting ��48

Chapter 5� Technical Support�� 51

This document contains proprietary information about

AIC products and is not to be disclosed or used except in

accordance with applicable agreements.

PREFACE

• Copyright

No part of this publication may be reproduced, stored in a retrieval system,

or transmitted in any form or by any means, electronic, mechanical, photo-

static, recording or otherwise, without the prior written consent of the

manufacturer.

• Trademarks

All products and trade names used in this document are trademarks or

registered trademarks of their respective holders.

• Changes

The material in this document is for information purposes only and is subject

to change without notice.

• Warning

1. A shielded-type power cord is required in order to meet FCC emission

limits and also to prevent interference to the nearby radio and television

reception. It is essential that only the supplied power cord be used.

2. Use only shielded cables to connect I/O devices to this equipment.

3. You are cautioned that changes or modications not expressly approved

by the party responsible for compliance could void your authority to

operate the equipment.

• Disclaimer

AIC shall not be liable for technical or editorial errors or omissions

contained herein. The information provided is provided "as is" without

warranty of any kind. To the extent permitted by law, neither AIC or its

affiliates, subcontractors or suppliers will be liable for incidental, special or

consequential damages including downtime cost; lost profits; damages

relating to the procurement of substitute products or services; or damages

for loss of data, or software restoration. The information in this document is

subject to change without notice.

SAFETY INSTRUCTIONS

• Before getting started, please read the following important cautions:

• All cautions and warnings on the equipment or in the manuals should be

noted.

• Most electronic components are sensitive to electrical static discharge.

Therefore, be sure to ground yourself at all times when installing the

internal components.

• Use a grounding wrist strap and place all electronic components in

static-shielded devices. Grounding wrist straps can be purchased in any

electronic supply store.

• Be sure to turn off the power and then disconnect the power cords from

your system before performing any installation or servicing. A sudden

surge of power could damage sensitive electronic components.

• Do not open the system’s top cover. If opening the cover for

maintenance is a must, only a trained technician should do so.

Integrated circuits on computer boards are sensitive to static electricity.

Before handling a board or integrated circuit, touch an unpainted

portion of the system unit chassis for a few seconds. This will help to

discharge any static electricity on your body.

• Place this equipment on a stable surface when install. A drop or fall

could cause injury.

• Please keep this equipment away from humidity.

• Carefully mount the equipment into the rack, in such manner, that it

won’t be hazardous due to uneven mechanical loading.

• This equipment is to be installed for operation in an environment with

maximum ambient temperature below 35°C.

• The openings on the enclosure are for air convection to protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

• Never pour any liquid into ventilation openings. This could cause re or

electrical shock.

• Make sure the voltage of the power source is within the specification

on the label when connecting the equipment to the power outlet. The

current load and output power of loads shall be within the specication.

• This equipment must be connected to reliable grounding before using.

Pay special attention to power supplied other than direct connections,

e.g. using of power strips.

• Place the power cord out of the way of foot traffic. Do not place

anything over the power cord. The power cord must be rated for the

iii

product, voltage and current marked on the product’s electrical ratings

label. The voltage and current rating of the cord should be greater than the

voltage and current rating marked on the product.

• If the equipment is not used for a long time, disconnect the equipment from

mains to avoid being damaged by transient over-voltage.

• Never open the equipment. For safety reasons, only qualified service

personnel should open the equipment.

• If one of the following situations arise, the equipment should be checked by

service personnel:

1. The power cord or plug is damaged.

2. Liquid has penetrated the equipment.

3. The equipment has been exposed to moisture.

4. The equipment does not work well or will not work according to its user

manual.

5. The equipment has been dropped and/or damaged.

6. The equipment has obvious signs of breakage.

7. Please disconnect this equipment from the AC outlet before cleaning.

Do not use liquid or detergent for cleaning. The use of a moisture sheet or

cloth is recommended for cleaning.

Product features and specications are subject to change without notice.

RSC-4H User's Manual

Chapter 1 Product Introduction

1�1 Box Content

Before removing the subsystem from the shipping carton, visually inspect the

physical condition of the shipping carton. Exterior damage to the shipping

carton may indicate that the contents of the carton are damaged. If any

damage is found, do not remove the components; contact the dealer where

the subsystem was purchased for further instructions. Before continuing, rst

unpack the subsystem and verify that the contents of the shipping carton are

all there and in good condition.

• Enclosure( Power supply, fan, 60 x 3.5'' HDD tray included)

• • Power cord Screws kit x 1pcs

• (Include console

serial cable)

• Slide rail x 1set

♦PACKAGE CONTENT MAY VARY PER REGION.

Chapter 1� Prodcut Introduction

• 3.5’’ HDD Tray

RSC-4H User's Manual

Chapter 1 Product Introduction

1.2 Specications

RSC-4H User's Manual

Chapter 1 Product Introduction

1�3 General Information

RSC-4H is a 4U rackmount chassis with external hot-swap HDD 60 x 3.5”HDD

and single 6G expander on HDD Backplane which is a high performance

server storage product.

• Front Panel

RSC-4H User's Manual

Chapter 1 Product Introduction

• Rear Panel

RSC-4H User's Manual

Chapter 1 Product Introduction

• Major Components

Chapter 2 Hardware Installation

RSC-4H User's Manual

2�1 Removing and Installing Top Cover

Pushing release button on both side and slide forward the top cover to

open cover.

Chapter 2� Hardware Installation

This chapter provides detailed instructions on hardware installation.

RSC-4H User's Manual

Chapter 2 Hardware Installation

2�2 Removing/Installing a Drive Tray

Hold the latch on top of the hard disk drive tray. Pull it out of the chassis.

Chapter 2 Hardware Installation

RSC-4H User's Manual

2�3 Installing/ Removing a Hard Disk Drive

Place the HDD into the hard disk carrier tray.

Please check if the screw holes on HDD match the dimples on HDD

tray.

note : THERE ARE 2 SCREWS HOLES RESERVED.

RSC-4H User's Manual

Chapter 2 Hardware Installation

2�4 Removing and Installing a PSU Module

2.4.1 Removing a PSU module

Grasp the tray handle tab. Pull the PSU module tray gently and

rmly until it clears the enclosure chassis.

2.4.2 Installing a PSU Module

Slide in PSU module. Make sure the latch on the module is fully

hooked on the PSU housing.

Chapter 2 Hardware Installation

RSC-4H User's Manual

2�5 Removing and Installing a Fan Module

2.5.1 Removing a fan module

Grabbing and removing the fan module from the fan slot.

Pull the fan module up gently and taking out the fan module by

removing rubbers out from the fan bar.

2.5.2 Installing a Fan Module

Make sure the 4 rubbers and connector insert rmly while fan module is

inserted.

RSC-4H User's Manual

Chapter 2 Hardware Installation

2�6 Removing and Installing HDD Backplane

2.6.1 Removing HDD Backplane

Unplugging all connectors & HDDs from HDD backplane.

Hold the lever to pull the Backplane out of chassis.

2.6.2 Installing a HDD Backplane

To install Backplane, follow the reverse order.

Chapter 2 Hardware Installation

RSC-4H User's Manual

2�7 Tool-less Blade Slide Installation Instruction

Separate the tool-less slide rail

2.7.1 Pull the inner rail out of the outer rail until it is fully extended.

Press the locking tab down to release the inner rail.

PULL

Outer Rail

Middle Rail

Inner Rail

RSC-4H User's Manual

Chapter 2 Hardware Installation

2.7.2 Place the inner rail rmly against the side of the chassis. Make sure

that the hooks are straight and aligned with the holes in the inner

rail.

Slide the inner rail forward until it clicks into the locked position.

Screw

RSC-4H User's Manual

Chapter 2 Hardware Installation

2.7.4 Hang the hooks of the rails on the rack holes and if necessary,

secure with screws.

Optional Screws

RSC-4H User's Manual

Chapter 3 Hardware Instruction

Chapter 3� Hardware Instruction

This chapter provides detailed instruction guide on hardware instruction

3�1 HARDWARE DESIGN SPECIFICATION

3.1.1 Placement

PCBA Placement

TOP

BOTTOM

HDD

RSC-4H User's Manual

Chapter 3 Hardware Instruction

3.1.2 Connector Location

Connector Location

HDD

CN1

JP1

U4 U3

Thermal Sensor Thermal Sensor

RSC-4H User's Manual

Chapter 3 Hardware Instruction

3.1.3 Power Connector

Power Connector

RSC-4H User's Manual

Chapter 3 Hardware Instruction

3.1.4 Console for Expander

Produkt Specifikationer

Mærke:	AIC
Kategori:	Ikke kategoriseret
Model:	RSC-4H
Bredde:	435 mm
Dybde:	950 mm
Højde:	177 mm
Produktfarve:	Sort
Antal blæsere:	4 blæser(e)
Grænseflade til lagerdisk:	Serial Attached SCSI (SAS)
Antal understøttede lagerdiske:	2
Datalagringsdriver installeret:	Ja
Kabinettype:	Stativ (4U)
Redundant strømforsyning:	Ja
Maksimalt understøttet lagerkapacitet:	- TB
Kapacitet af datalagringsdrev:	12 GB
Samlet installeret lagerkapacitet:	- GB
Strømforsyningens kapacitet (PCU):	1600 W
Antal strømforsyninger:	2
Antal af hovedstrømforsyninger:	1
Antal understøttede overflødige strømforsyninger:	1