Aiwa ICM120 Manual


Læs gratis den danske manual til Aiwa ICM120 (8 sider) i kategorien Stemmeoptager. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Aiwa ICM120, eller vil du spørge andre brugere om produktet?

Side 1/8
ENGLISH
OWNER’S RECORD
For your convenience, record the model number and serial number (you will
find on the rear of your set) in the space provided below. Please refer to
them when you contact your AIWA dealer in case of difficulty.
Model No. IC-M120
Serial No.
PRECAUTIONS
To maintain good performance
Do not use the unit in places which are extremely hot, cold, dusty or
humid.
In particular, do not keep the unit:
in a high humidity area such as a bathroom
near a heater
in an area exposed to direct sunlight (inside a parked car, where there
could be a considerable rise in temperature)
Keep cassette tapes, magnetic cards and other magnetic recorded
materials away from the speaker as the recorded information may be
erased or noise may occur on cassette tapes.
When an erroneous display or operation occurs b A
Reset the unit by pressing the RESET button inside the battery compartment
with a thin rod. Recordings are not erased when you reset the unit.
ATTENTION
Recordings may be erased when this unit is serviced.
INSERTING DRY CELL BATTERIES b B
Open the battery compartment and insert two size AAA (R03) batteries with
the 0 and 9 marks correctly aligned.
Battery replacement
Replace the batteries when flashes in the display. Operation stops
automatically 20 seconds after the starts flashing.
Note
After replacing the batteries, an erroneous display may occur. In this case
press the RESET button inside the battery compartment with a thin rod to
reset the unit . Recordings are not erased when you reset the unit. b A
Note on dry cell batteries
Make sure that the 0 and 9 marks are correctly aligned.
Do not mix different types of batteries, or an old battery with a new one.
To prevent the risk of electrolyte leakage or explosions, never recharge the
batteries, apply heat to them, or take them apart.
When not using the batteries, remove them to prevent needless battery
wear.
If liquid leaks from the batteries, wipe thoroughly to remove.
PREPARATION
HOLD switch b C
Release the HOLD switch before operation to activate the buttons. b a
When not using the unit, set the HOLD switch to HOLD position. b b
Accidentally pressed buttons will not function.
If a button is pressed when the HOLD switch is set to the HOLD position,
“hold” flashes in the display.
Turning on and off
Press REC/STOP, c/sPLAY/STOP, MODE/PAUSE or FILE to turn on the
power. When c/sPLAY/STOP is pressed, the power is turned on and
playback starts.
If no new operations are done within 1 minute from the last operation, the
power is turned off automatically (Auto Power off function).
To attach the hand strap b D
To clean the cabinet
Use a soft cloth lightly moistened with a mild detergent solution.
Do not use strong solvents such as alcohol, benzine or cleaner.
RECORDING FROM THE BUILT-IN MICROPHONE b E
This unit has 4 recording files (A, B, C and D). You can record in 100
recording tracks on each recording file.
1 Release the HOLD switch.
2 Press MODE/PAUSE repeatedly to select a recording mode.
SP: You can record for up to about 56 minutes.
LP: You can record for up to about 120 minutes.
V-SPk: You can record for up to about 56 minutes with the V-SENSOR
function.
V-LPk: You can record for up to about 120 minutes with the V-SENSOR
function.
Select SP to record the sound more clearly.
About the V-SENSOR function, please refer to “V-SENSOR function”
below.
3 P FILE t dl t l t di fil
IC-M120
IC RECORDER
GRABADOR EN CIRQUITO INTEGRADO
OPERATING INSTRUCTIONS
INSTRUCCIONES DE MANEJO
MODE D’EMPLOI
8A-HY7-911-01
000822AYO-OX
Printed in Korea
AAA (R03) × 2
RESET
4
A
B
C
D
E
IC-M120(YU)ESF
Select SP to record the sound more clearly.
About the V-SENSOR function, please refer to “V-SENSOR function”
below.
3 Press FILE repeatedly to select a recording file.
4 Orient the built-in microphone to the sound source.
5 Keep REC/STOP pressed for 1 second.
The REC indicator lights up in red, then recording starts.
a Recording track number
b Recording indicator
c Recording mode
d V-SENSOR indicator
e Elapsed recording time
Basic operation
Note
You cannot change the recording file during recording.
To see the remaining recording time
Press FILE during recording or while in recording pause mode. The
remaining recording time is displayed while the button is pressed.
The remaining recording time is approximate values.
When FULL is displayed
You cannot record any more. Erase unnecessary recordings.
V-SENSOR function
If you select V-LPk or V-SPk in step 2, the recording starts when the unit
detects sound above a preset level. If the unit does not detect the sound for
about 2 seconds, recording will pause and “SEnS” flashes.
This function prevents memory waste and empty recording.
Note
The sensor level is factory-preset and you cannot change the level. Before
using the V-SENSOR function, please be sure to record once to confirm
the sensor level.
When recording resumes after sound detection, the very first sounds may
not be recorded.
1 2
3
4
5
3
2
1REC
MODE /PAUSE
5
Press REC/STOP or c/sPLAY/STOP.
Press MODE/PAUSE.
To resume, press MODE/PAUSE, REC/STOP or
c/sPLAY/STOP.
To stop recording
To pause recording
REC/STOP
E
FILE


Produkt Specifikationer

Mærke: Aiwa
Kategori: Stemmeoptager
Model: ICM120

Har du brug for hjælp?

Hvis du har brug for hjælp til Aiwa ICM120 stil et spørgsmål nedenfor, og andre brugere vil svare dig