Alpine PWE-V80 Manual

Alpine Bilhøjttaler PWE-V80

Læs gratis den danske manual til Alpine PWE-V80 (2 sider) i kategorien Bilhøjttaler. Denne vejledning er vurderet som hjælpsom af 30 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 15.5 anmeldelser. Har du et spørgsmål om Alpine PWE-V80, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SUBWOOFER INSTALLATION

ACCESSORIES

SPECIFICATION

8 INCH SUPER COMPACT ACTIVE SUBWOOFER

MAX POWER OUTPUT 160W...............................................

CROSSOVER 30-160Hz (-12dB/oct)..............................................................

PHASE ......................................................................... 0°,180°

INPUT SENSITIVITY 80mV-0.5V (Line Input)

0.9V-6V (Speaker Input)

OPERATIONAL VOLTAGE DC 14.4V (Operational between: 11~16V)..........................................

DIMENSIONS 342mmX238mmX80mm..............................................................

WEIGHT 5 Kg.......................................................................

Subwoofer Installation Place

Under the seat

Under the seat In the trunk

Line controller

Speaker output wire

Caution: Subwoofer warms up during continuous usage. Please make sure

that it is not covered and the installation place provides free space to the unit.

Installation place and method must not damage electrical wirings, gasoline

tank and other objects which might cause short circuit, fire, etc.

1. Mount the installation bracket onto the bottom of the subwoofer (4 brackets, 4 screws).

2. Fix the brackets on the body of the vehicle (4 brackets, 4 screws).

10P connection couple

(Power line, remote start wire,

speaker input wire, ground wire)

5M power extension coupler (12AWG)

Remote start wire

Mounting bracket

Fixed screw (locking vehicle)

Fixed screw (locking body)

PWE-V80

Instruction Manual

Subwoofer PWE-V80

Brackets and screws

1. CONNECTION 2. ADJUSTMENT

CONNECTIONS FOR RCA INPUT

CONNECTIONS FOR SPEAKER LEVEL INPUT

POWER INDICATOR

INPUT GAIN ADJUSTMENT

LOW PASS FILTER ADJUSTMENT

PHASE SELECTOR

Remote start (blank without)

White

Red

Pre-out

RCA lead

(sold separately)

RCA lead (L TYPE)

Remote start

Ground connection

Remote start

Blue/White

Black

Yellow

FUSE (10A)

Yellow

Yellow Yellow

FUSE

(10V)

Battery extension lead

Ground connection

Battery extension lead

White/black

Ash

Ash/black

Left Speaker

Right Speaker

POWER SUPPLY & SPEAKER LEVEL INPUT

Remote on

Left Speaker Output

Right Speaker Output

Head Unit

1 Disconnect the cable from the negative terminal of the car battery.

2 Connect

This product cannot be used in cars fitted with a common negative speaker system.

To prevent external noise from entering the audio system:

If there is distortion or you hear a popping sound from the subwoofer,

the input level is too high.

If the subwoofer has prolonged use in this condition, this may result

in deterioration of performance or may cause damage to the

subwoofer.

1. Set the gain to MIN, Phase to NORM.LPF to CENTER before

swithing on the system.

2. Set the Bass/Treble adjustment to zero on the head unit. Set

the volume to your average listening level. lt may help to use a

music source that is familiar.

3. Next, gradually increase the gain level and system volume to a

point where system balance is achieved. If the gain level is set

too high, the subwoofer may begin to distort. Distortion may

also occur if the volume is set too high on the head unit. Check

that the other speakers have not begun to distort before

proceeding with the adjustment. If the entire speaker system in

the car is distorting, reduce the volume of the head unit.

4. Once the gain has been set, adjust the L.P.F (Low Pass Filter)

at afrequency which compliments your speaker system.

(We recommend using CENTER as a starting point.)

5. Adjusting the L.P.F will change the output volume of the

subwoofer. Repeat procedures 3 and 4 until the ideal setting is

found.

6. The final adjustment is the PHASE of the subwoofer. While

sitting in the driver's seat and with music playing, switch to a

better setting between NORM and REV - The ideal PHASE

setting varies from car to car, depending on the location of the

subwoofer and the interior acoustic characteristics of the car.

Locate the unit and route the leads at least 10 cm away from the car harness.

Keep the power lines as far away from other leads as possible.

Connect the ground lead securely and safely to a bare metal spot (remove the coating if

necessary) of the car chassis.

If you add an optional noise suppressor, connect it as far away from the unit as possible. Your

Alpine Dealer can provide various noise suppressor solutions, contact them for further information.

Your Alpine Dealer knows best about noise prevention measures so consult your dealer

for further information.

Ensure secure connections.

Any unused connections should be insulated with electrical insulation tape.

If the on-board computer or similar device, such as the ECU, contains security code,

you may loose the memory when connecting the negative lead.

If your head unit does not have this lead, then please

connect to the the ACC lead of the vehicle.

The lead that supplies power when the key is at the

ACC position.

Please connect to either the rear or

front speaker output leads.

- Caution

The output of the subwoofer will be

affected by the head unit fader settings.

Connect to the ACC line if the head

unit has no remote start lead.

Always use the extension

cable supplied for connecting

the +VE battery terminal.

DO NOT connect this lead to

the head unit.

DO NOT modify this cable.

It may cause malfunction and

damage to the product

Always use the extension

cable supplied for

connecting the +VE battery

terminal.

DO NOT connect this lead

to the head unit.

DO NOT modify this cable.

It may cause malfunction

and damage to the product

Connect the ground lead securely

and safely to a bare metal point

on the vehicle chassis.

Connect the ground lead

securely and safely to a

bare metal point on the

vehicle chassis.

Failure to do so may result in fire, accident or electrical shock.

Type of Lead

Remote turn on lead

Connect to the remote start lead of the head unit.

• If your head unit does not have this lead, then please connect to the the ACC lead of the vehicle. The lead supplies

power when the key is in the ACC position.

Attach securely and safely to a bare metal spot on the car's chassis.

Connect directly to the positive terminal of the car's battery.

Ground lead

Power line

Additional Information

Bolts or nuts used for the brake or steering systems (or any other safety related system), or tanks should NEVER be used

for installations or ground connections. Using such parts could disable control of the vehicle and cause fire, etc.

POWER SUPPLY &

SPEAKER LEVEL INPUT

Left speaker

input

Right speaker

input

Ground

wire

Power

supply

CAUTION

Produkt Specifikationer

Mærke:	Alpine
Kategori:	Bilhøjttaler
Model:	PWE-V80
Bredde:	342 mm
Dybde:	80 mm
Højde:	238 mm
Vægt:	5000 g
Produktfarve:	Sort
Produkttype:	Forbelastet subwoofer
Subwoofer RMS-effekt:	160 W
Subwoofer type:	Aktiv subwoofer
Subwoofer frekvensomrpde:	50 - 100 Hz
Subwoofer spidseffekt:	160 W
Vurderet effekt:	160 W
Maksimal strøm:	160 W
Indkapslingstype:	Lukket