Anda Seat X-Air Pro Manual

Anda Seat Kontorstol X-Air Pro

Læs gratis den danske manual til Anda Seat X-Air Pro (2 sider) i kategorien Kontorstol. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Anda Seat X-Air Pro, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

FEATURES

WHAT'S IN THE BOX

ASSEMBLY STEPS

Press the casters into the

wheelbase.

Insert the gas piston into

the wheelbase.

Flip the seat base over, remove

the pre-installed M6×16 bolts and

washers, and use them to install

the tilt mechanism.

Thread the tilt mechanism's

levers through the hole on the

seat base frame and secure them

with ST4×35 screws.

Place the gas piston into

the seat base.

Turn the chair upright to

complete the assembly.

Attach the headrest onto the

backrest with M6×16 bolts.

Mount the armrests with M6×25

bolts and washers.

Align the backrest to the seat

base and secure them with

M8×16 bolts and washers.

① ②

③

④

⑤

⑥

⑦

⑧

⑨ ⑩

Headrest ×1

Backrest ×1

Seat Base ×1

Tilt mechanism ×1

Tilt Mechanism Wire Cover ×1

Armrests ×2

Gas Piston ×1

J K

Bolts & washers ×3

M N O

Wheelbase ×1

Casters ×1

M8×16

Bolts & washers ×6

M6×25

Bolts ×2

M6×16

Screws ×6

ST4×35

Hex Wrench ×1

M5&M4

Screwdriver ×1

Extendable Seat Depth :

47-53cm extension for optimal

thigh space and comfort.

Rotating Armrests

with 9-Level Heights:

Double-pivot rotation: 360°

for the upper pivot and 220°

for the lower.

Backrest Recline:

105°~126° adaptive recline

with a 4-position tilt lock

for different postures.

3D Headrest:

Up-down adjustability with

double-pivot rotation.

Backrest Height Adjustment:

8cm up-down range in 7 different

levels for customizable support.

Seat Height Adjustment:

10cm height range offering

ideal leg space for all

ﬁgures.

pre-installed

Arrange the tilt mechanism wires

to the hole's sides. Use your

hands to click one end of the wire

cover into the hole, then press

the other end into place using the

included wrench or a ﬂat tool.

HOW TO ADJUST

Hold armrests ﬁrmly to:

Move up or down to the ideal height.

Slide forward or backward.

Rotate the upper pivot 360° or the lower pivot 220°.

Armrests:

Pull the left-side lever upward, move the seat

with your hip to the ideal depth, and release the

lever to lock in.

Seat Depth:

To raise: Stand on your feet, pull the height lever

upward, and release to lock in.

To lower: Pull the height lever upward and release

to lock in.

Seat Height(while sitting):

Using both hands, lift the backrest with steady and

gradual force. For the lowest height, lift it rapidly

to the highest and release.

Backrest Height:

Lean back gradually to the desired angle and pull

the recline lever upward to lock in.

Backrest Recline:

Hold with both hands to move it up-down or rotate

30° with front pivot and 38° with back pivot.

Headrest:

ASSEMBLY TIPS

1. Closely follow the Assembly Steps and refer to the illustrations for correct assembly.

2. Check every component in the box and conﬁrm they are in working condition.

3. Safety gloves are recommended for assembly.

4. To prevent accidental component damage, assemble on a clean, even surface with

a protective layer.

5. To prevent misalignment or uneven tightening, install each bolt halfway, adjust if

needed, then fully tighten.

6. The gas piston stays tight in place once it's assembled.

If you need to disassemble the chair and pack it for transportation:

1. Lay it on its side, hold the gas piston ﬁrmly, and lightly twitch the seat or tap on

its back side with a rubber hammer until it detaches from the gas piston.

2. Then tap on the wheelbase to get it loose from the gas piston.

Note: Please take safety precautions during this process. Any damage or safety

issue that occurs from it is not covered by this product's warranty.

USAGE TIPS

1. This is a single-person chair. Use it with only one person at a time.

2. Ensure all components are securely fastened before use. Inspect bolt tightness

every 3 months to maintain safety.

3. Place the chair on a level surface. Avoid prolonged exposure to excessive

moisture, heat, or direct sunlight.

4. For seated use only. Do not stand on the chair or sit on its armrests.

5. Clean the chair's surface before your ﬁrst use. Wipe with a soft cloth only.

6. Avoid cleaners with high acid or alkaline, as they may corrode or damage the

chair surface.

7. Use the chair features as shown in the How To Adjust section.

8. While reclining, lean back gradually and keep yourself balanced. Flinging back too

hard or too far might cause tipping.

9. Do not take apart the gas piston for safety.

FOR THE WINNERS’ CIRCLE

ASSEMBLY GUIDE

X-AIR PRO

MESH

CHAIR

Produkt Specifikationer

Mærke:	Anda Seat
Kategori:	Kontorstol
Model:	X-Air Pro

Har du brug for hjælp?

Hvis du har brug for hjælp til Anda Seat X-Air Pro stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Kontorstol Anda Seat Manualer

Anda Seat X-Air Pro Manual

17 December 2024

Kontorstol Manualer

Nyeste Kontorstol Manualer

Defender Polo Manual

17 September 2025

Mark Adler Boss 6.0 Manual

16 September 2025

Defender Madrid Manual

16 September 2025

Defender Sofia Manual

16 September 2025

Defender IKA Manual

16 September 2025

Defender Varna Manual

16 September 2025

Mark Adler Junior 3.0 Manual

16 September 2025

Fantastic Ventura Manual

10 September 2025

Black Point O'Kneel Manual

9 September 2025

Interstuhl VINTAGEis5 17V7 Manual

8 September 2025