APC ACCS2006 Manual

APC Ikke kategoriseret ACCS2006

Læs gratis den danske manual til APC ACCS2006 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6 anmeldelser. Har du et spørgsmål om APC ACCS2006, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

990-91538 10/2021

Worldwide Customer Support

Customer support and warranty information is available at

www.se.com

Air Containment Adapter Kits

(300mm) Installation

ACCS2004 - ACCS2005 - ACCS2006 - ACCS2007

ACCS2004 and ACCS2005 compatible with ACRD101, ACRD301

ACCS2006 and ACCS2007 compatible with ERC301CW

IMPORTANT SAFETY INSTRUCTIONS

Receiving

Inspect the Equipment

Carefully inspect the shipment for visible signs of damage. If you detect shipping

damage, contact your shipping company immediately and Schneider Electric Customer

Support at www.se.com.

Storage

These components should be stored indoors and out of the weather. Do not allow the

panels to be exposed to the elements.

CAUTION

HEAVY EQUIPMENT HAZARD

• The kit components are heavy. Use caution when lifting.

• Wear appropriate personal protective equipment (PPE) and follow safe work

practices.

Failure to follow these instructions can result in injury or equipment damage.

NOTICE

• Leaving the kit components uncovered and exposed to the elements will cause

damage and void the factory warranty.

• Wipe the panels with a damp cloth to clean. Do not use solvents or abrasive

cleaners.

Inventory

Item Description Qty

Adapter side frame with door hinges 1

Grounding Wire

1 inside adapter door, 1 on inside rear of hinge side adapter frame.

Adapter door handle side frame 42U 1

ACCS2004 Door 1

Door Handle (installed on doors) 2

ACCS2006 Door 1

Door (Rear adapter kits) 1

Adapter top 1

Adapter bottom 1

EVA foam seal 2.0 x 20 x 2000 (mm) 1

Display RJ45 connector adapter (for use with ACRD101 only) 1

Display interface connector cable (for use with ACRD101 only) 2

M6 flanged hex nut 8

Washer M6 serrated 2

Washer Nylon ID 6 PD 12 6

M5 flanged hex nut 1

Screw M6 x 12 Pan head T30 Nylok 6

Screw M8 x 12 Flat head Nylok T30 4

Screw M5 x 10 Pan head T25 3

Screw M6 x 12 Pan head T30 1

Recycle or dispose of the packaging materials appropriately.

ns3367a

Tools Required (not provided)

Prepare the Cooling Unit

Each kit contains the parts for one (front or

rear) installation.

Refer to your cooling unit’s manual for in-

structions for the below tasks.

1. Disconnect the cable from the

display interface.

2. Remove the front and rear doors from the

cooling unit.

3. Remove the hinges from the

cooling unit, if applicable.

NOTE: 1. In existing rows of racks, the

joining brackets securing the racks and

cooling units together on the front side are

not removed.

2. All racks in the row must be level and

secured together with the joining brackets (at

the front) prior to installing the air

containment adapters.

T25 and T30 Torx

head screwdrivers

8-mm, 10-mm, 13-mm

wrenches

Scissors Level

ns3371a

Cooling Unit Display

Install Air Containment Kit Mounting Screws

Install six (6) M6 x 12 Pan head T30 screws and six (6) nylon

washers (provided) to the front and rear of the cooling unit in the

holes corresponding to the mounting holes in the Air Containment

frame. The screws are installed only halfway to leave room to

place the Air Containment frame over the screw heads.

Assemble the Air Containment Kit

Frame

Insert the four (4) threaded posts on top and

bottom parts through the holes at the top and

bottom of the left and right frame pieces.

Once the top and bottom are set into the side

frames, secure them with eight (8) M6 flanged

hex nuts using a 10-mm wrench.

NOTICE

Remove the Display Interface from the Cooling Unit Door. Save the Display Interface

and its mounting hardware for installation to the adapter door.

CAUTION

HEAVY EQUIPMENT HAZARD

Some of the components of the Air Containment Kit are heavy. It is recommended

that two (2) people lift and move the larger parts.

Failure to follow these instructions can result in injury or equipment damage.

Display from ACRD301

Save 2 screws

Save

3 screws

Save

2 screws

Display from ACRD101

ns3372a

ns3366a

Apply the Gasket Material

1. Cut the gasket material to size.

2. Peel the backing paper from the

gasket, exposing the glue.

3. Apply the gasket material to the top

and bottom of the frame, pressing to

secure the gasket in position.

Install the Air Containment Frame

1. Hang the Air Containment frame on the

screws leaving the washers between the

frame and the Cooling Unit.

2. Tighten the six (6) M6 x 12 Pan head T30

screws to secure the air containment frame to

the rack. Use a level (not provided) to make

sure the frame and Cooling Unit are level.

3. Lower and adjust the leveling feet of the

adapter using a 13-mm wrench (not provided)

while still using the level.

Attach the ground wire on the rear of the Air Containment frame to the rack in the row

next to the cooling unit using one (1) M6 serrated washer and one (1) M6 x 12 pan head

T30 screw (provided).

NOTE: There is a ground wire on all Air Containment frames.

Backing

ns3376a

ns3377a

ns3379a

Ground wire on

adapter frame

Attached to

rack frame

Install the Door

1. Install the door to the Air Containment frame by lifting the door until the receivers on

the door are positioned above the hinge pins on the frame and then lowering the door

until the receivers engage the hinge pins.

2. Attach the ground wire on the Air Containment frame to the threaded stud on the

door using one (1) M6 serrated washer and one (1) M5 flanged nut provided in the

hardware bag.

Install the Cooling Unit Display Interface

to the Adapter Door

Use the hardware saved when the display was

removed from the cooling unit to install the display

interface in the door of the adapter.

Install the cover (ACCS2004) to the door using four

(4) flanged hex nuts provided.

NOTE: For ACRD101 Cooling Units, the cable

extension and connector will be required. Install the

cable and connector to the display cable.

Join the Air Containment Adapters

When multiple Air Containment Kits are installed in a row of

racks, the adapter side frames are secured to the next side

frame in the row using three (3) M5 x 10 Pan head screws

provided in the hardware bag with your kit.

ns3381a

ns3373b

ns3387a

Produkt Specifikationer

Mærke:	APC
Kategori:	Ikke kategoriseret
Model:	ACCS2006
Bredde:	300 mm
Produktfarve:	Sort
Harmoniseret systemkode (HS):	85389099
Rackkapacitet:	42U

Har du brug for hjælp?

Hvis du har brug for hjælp til APC ACCS2006 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret APC Manualer

APC AR7752W Manual

30 August 2025

APC E3SXR7 Manual

5 August 2025

APC E3MCBC7D Manual

4 August 2025

APC Galaxy VS GVSOPT004 Manual

4 August 2025

APC PME5B-GR Manual

4 August 2025

APC SRT192RMBPM Manual

15 Juli 2025

APC EPDU1216B Manual

15 Juli 2025

APC APV9602 Manual

15 Juli 2025

APC AP7922B Manual

15 Juli 2025

APC InRow RC ACRC500 Manual

7 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kimo LR 110 Manual

2 September 2025

HMS Premium LPD02 Manual

2 September 2025

AVer E1008 Manual

2 September 2025

Biltema 17-547 Manual

2 September 2025

Groen AH/1E Manual

2 September 2025

ACOPower HY-P30 Manual

2 September 2025

Yamaha True X Speaker 3A WS-X3A Manual

2 September 2025

Globe RG30 Manual

2 September 2025

Deye SUN-6K-SG05LP1-EU-AM2-P Manual

2 September 2025

Neutrik NLT4FXX Manual

2 September 2025