APC Back-UPS 550 Manual

APC Uafbrydelig strømforsyning (UPS) Back-UPS 550

Læs gratis den danske manual til APC Back-UPS 550 (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om APC Back-UPS 550, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Safety

Specifications

Connect the Battery

The Back-UPS is shipped with one battery cable disconnected. Remove the “Stop!

Connect the Battery”

label that covers the outlets.

Prior to connecting any equipment

to the unit, connect the battery cable to the unused battery terminal. It is normal for

small sparks to be seen when the battery cable is connected to the battery terminal.

Wall Mount Installation

• Horizontal installation, use 2 screws 7.3" (186.3 mm) apart.

• Vertical installation, use 2 screws 5.4" (137.2 mm) apart.

• Allow 5/16" (8 mm), of the screw to protrude from the wall.

Replace Battery

Use only approved APC replacement battery cartridges.

Deliver used batteries to a battery replacement facility in the packaging provided by

APC with the replacement battery cartridge. To order replacement battery cartridges

contact APC.

Connect Equipment

Battery Backup + Surge Protection Outlets

Battery backup outlets provide protection to connected equipment when the

Back-UPS is turned on and connected to utility power.

Battery backup outlets receive power from the Back-UPS for a limited period of time

when a power outage, or brownout condition occurs.

Battery backup outlets provide protection from power surges or spikes.

Connect a computer, monitor and other peripheral devices to the outlets.

Surge Protection Outlets

Surge protection outlets provide protection to connected equipment when the

Back-UPS is connected to utility power, and is switched on or off.

Surge protection outlets provide protection from power surges or spikes.

Connect a printer, scanner or other peripheral devices that do not need to remain on

during power outages, or utility problems to the surge protection outlets.

Connect Network

The Back-UPS protects equipment connected to a 10/100 Base-T ethernet, from

power surges when connected through the Back-UPS coaxial connectors.

PowerChute® Personal Edition Software

Overview

Use PowerChute Personal Edition software to configure the UPS settings.

Protect your computer and other equipment during a power outage. During a power

outage, PowerChute will save any open files on your computer and safely shut it

down. When power is restored, it will restart the computer.

Configure the UPS to use features such as power-saving outlets, shutdown

configuration, and alarms.

Monitor the UPS for power usage and power events.

Note: PowerChute is only compatible with a Windows operating system. If you are

using a Mac OSX, use the native shutdown feature to protect your system. See the

documentation provided with your computer.

Installation

Use a USB cable to connect the Data port on the rear panel of the UPS to the USB port

on your computer.

If the Back-UPS came with CD into your computer and a PowerChute CD, insert the

follow the on-screen instructions

If the Back-UPS did not come with a PowerChute CD, go to www.apc.com and

download the software free of charge.

Turn On the Back-UPS

Press the POWER

ON button located on the top of the Back-UPS.

The Power On/

Replace Battery LED will illuminate and a single short beep will be audible to

indicate that the Back-UPS is providing protection for connected equipment.

The Back-UPS battery charges fully during the first 16 hours while connected to

utility power. The Back-UPS battery will charge while the Back-UPS is switched on

or off and is connected to utility power. Do not expect full battery run capability

during the initial charge time.

If the red Building Wiring Fault LED located on the side of the Back-UPS

illuminates, do not operate the Back-UPS. Have a qualified electrician correct the

building wiring fault.

Warranty

The standard warranty is 3 years in the USA and Canada, 2 years in all other regions

from the date of purchase. APC standard procedure is to replace the original unit with

a factory reconditioned unit. Customers who must have the original unit back due to

assigned asset tags and set depreciation schedules must declare such a need at first

contact with APC Technical Support. APC will ship the replacement unit once the

defective unit is received by the repair department or cross-ship upon the provision of

a valid credit card number. The customer pays for shipping to APC, and APC pays

ground freight transportation costs back to the customer.

This unit is intended for indoor use only.

Do not operate this unit in direct sunlight, in

contact with fluids, or where there is excessive

dust or humidity.

Connect the Back-UPS power cord directly to a

wall outlet. Do not use a surge protector or an

extension cord.

Input

Voltage 120 Vac Nominal

Frequency 60 Hz + 3

Brownout Transfers 92 Vac Typical

Over-voltage Transfer 139 Vac Typical

Output

UPS Capacity

(4 battery backup outlets)

BE450G: 450 VA, 257 W;

BE550G: 550 VA, 330 W;

BE650G1: 650 VA, 390 W

Total Amperage (all outlets) 12 A (including UPS output)

Voltage - On Battery 115 Vac ± 8%

Frequency - On Battery 60 Hz + 1

Transfer Time 6 ms Typical, 10 ms maximum

Protection

and

Filtering

AC Surge Protection Full time, 340 Joules

EMI/RFI Filter Full time

AC Input Resettable circuit breaker

Battery

Type Sealed, maintenance-free, lead acid

BE450G: RBC114

BE550G: RBC110

BE650G1: RBC17

Average Life 3 - 5 years depending on the number of

discharge cycles and environmental

temperature

Physical

Net Weight Replacement battery cartridge

BE450G: 10 lb (4.7 kg)

BE550G: 12 lb (5.5 kg)

BE650G1: 14 lb (6.2 kg)

Dimensions

Length x Width x Height

12 in x 7 in x 3 in

30 cm x 18 cm x 9 cm

Operating Temperature 32º F to 104º F (0º C to 40º C)

Storage Temperature 5º F to 113º F (–15º C to 45º C)

Operating Relative Humidity 0 to 95% non-condensing humidity

Operating Elevation 0 to 10,000 ft (0 to 3000 m)

EMC

Compliance

This device complies with part 68 and part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired

operation.

 Press the battery compartment cover

release tab located on the rear side of the

unit. Slide the battery cover off.

 Connect the battery cable securely to the

battery terminal.

 Reinstall the battery compartment cover.

Be sure that the release tab locks into place.

bu064a

bu065a

bu066a

bu202a

Back-UPS

Battery Backup + Surge Protection

Surge Protection

bu201a

CAUTION-Refer to bottom

of unit for safety markings.

Circuit

Breaker

Building

Wiring Fault

PowerChute

USB Port

Network

Out

Push to

Reset

Network

User Manual Back-UPS® BE 450G/550G/650G1

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	Back-UPS 550
Bredde:	224 mm
Dybde:	311 mm
Højde:	89 mm
Vægt:	6020 g
Produktfarve:	Sort
Pakkevægt:	6930 g
Pakkedybde:	400 mm
Pakkebredde:	279 mm
Pakkehøjde:	127 mm
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Kompakt
Opbevaringstemperatur (T-T):	-15 - 40 °C
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 95 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 40 °C
Støjniveau:	40 dB
Udgangseffekt:	330 W
Certificering:	GOST, REACH, UL 1449
LED-indikatorer:	Ja
Kabellængde:	1.83 m
Antal understøttede batterier:	1
Opladningstid for batteri:	16 t
Bæredygtighedscertifikater:	RoHS
Driftshøjde:	0 - 9000 m
Ikke-drift højde:	0 - 9000 m
Indgangsfrekvens:	50/60 Hz
Lydalarmer:	Ja
Nominel udgangsspænding:	220 V
Nominel indgangsspænding:	220 V
Modem-porte (RJ-11):	1
AC udgange, antal:	8 AC stikkontakt(er)
AC stikkontakt typer:	Type F
Overspænding energivurdering:	450 J
Indgående driftsspænding (maks.):	278 V
Output strømkapacitet (VA):	0.55 kVA
Indgående driftsspænding (min.):	160 V
Udgangs driftsspænding (min.):	- V
Udgangs driftsspænding (maks.):	- V
Beskyttelsesfunktioner mod strømstød:	Fax,Modem,Network,Telephone
Strøm (maks.):	10 A
Typisk backup tid ved halv styrke:	12 min.
Typisk backup tid ved fuld styrke:	3 min.
Koldstart:	Ja
Hot-swap batteri:	Ja