APC BE350G Manual

APC Uafbrydelig strømforsyning (UPS) BE350G

Læs gratis den danske manual til APC BE350G (6 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 23 anmeldelser. Har du et spørgsmål om APC BE350G, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Back-UPS® ES 350G

User Guide

Connect Battery

Equipment

Turn on the Unit

Surge Protection

These outlets provide full-time protection from surges even if the

Back-UPS ES is switched OFF. Plug your printer, fax machine,

scanner, or other peripherals that do not need battery power into

these outlets.

Battery Back-up +Surge Protection

These outlets are powered whenever the Back-UPS ES is

switched ON. During a power outage or other utility problems

(brownouts, over-voltages), these outlets will be powered for a

limited time by the Back-UPS ES. Plug your computer,

monitor, and other peripheral devices into these outlets.

Press the ON/OFF switch to turn on the unit.

A single short beep and the green “Power On” indicator

confirms the Back-UPS ES is on and ready to provide

protection.

The Back-UPS ES should charge for at least 16 hours to

ensure sufficient runtime. The unit is being charged whenever

it is connected to utility power, whether the unit is turned ON

or OFF.

If the red Building Wiring Fault indicator (located on the end

near the power cord) is lit, your building wiring presents a

shock hazard that should be corrected by a qualified

electrician.

.apc.com

The Back-UPS ES indicates operating status using a combination of visual and audible

indicators. Use the following table to identify the status of the Back-UPS ES.

Status Visual Indication Audible Alarm Alarm Terminiation

Power On - UPS is

supplying conditioned utility

power to the load.

Power On pushbutton

- ON (lit)

None Not applicable.

On Battery - UPS is

supplying battery power to

the load connected to the

Battery outlets.

Power On pushbutton

- ON (off during beep)

Beeping 4 times every

30 seconds

UPS transfers back to

Power On operation, or

when UPS is turned off.

Low Battery Warning -

UPS is supplying battery

power to the load

connected to the battery

outlets, and the battery is

near exhaustion.

Power On indicator is

flashing

Rapid beeping (every

1/2 second)

UPS transfers back to

normal operation, or when

UPS is turned off.

Replace Battery - The

battery is disconnected.

The battery is in need of

charging, or is at the end of

its usual life and must be

replaced.

Replace Battery

indicator is Flashing

Power On and Replace

Battery indicators -

flashing (alternating)

Constant tone

UPS is turned off with the

power switch.

Overload Shutdown -

During On Battery

operation a battery power

supplied outlet overload

was detected.

None Constant tone UPS is turned off with the

power switch.

Sleep Mode - During On

Battery operation the

battery power has been

completely exhausted and

the UPS is waiting for utility

power to return to normal.

None Beeping once every 4

seconds

Utility power is restored, or

if utility power is not

restored within 32 seconds,

or the UPS is turned off.

Building Wiring Fault -

Your building wiring

presents a shock hazard

that should be corrected by

a licensed electrician.

Building Wiring Fault

LED (red) - ON

None UPS is unplugged, or UPS

is plugged into a properly

wired outlet.

Status Indicators

For safety, the Back-UPS ES is shipped with one battery wire disconnected. The UPS will not operate until the wire is connected to the touch-safe

battery terminal. NOTE: Small sparks may occur during battery connection. This is normal.

Turn the Back-UPS ES over and press in the

release tab. Slide the plastic battery cover

off of the Back-UPS.

Insert the battery back into the compartment.

Slide the plastic battery cover until the release

tab locks into place.

Connect the battery wire firmly to the

battery terminal.

1 2 3

Connect

Connect Modem / Phone / DSL / Fax

The Back-UPS protects a single line (2-wire) phone (including Digital Subscriber Line -

DSL), Home Phoneline Networking Association (HPNA) type equipment, modem, or fax

machines from surges when connected through the UPS as shown in the drawing below.

Place the Back-UPS ES to avoid:

- Direct sunlight

- Excessive heat

- Excessive humidity or contact with fluids

Plug the Back-UPS ES power cord directly into a wall outlet; not into a surge

protector or power strip.

4Transfer Voltage and

Sensitivity Adjustment

(Optional)

In situations where the Back-UPS, or connected equipment, is too

sensitive to the input voltage, it may be necessary to adjust the

transfer voltage. To adjust the transfer voltage:

1. Plug the Back-UPS into the utility power source. The Back-

will be in “Standby mode” (no indicators are lit).

2. Press the ON/OFF push button fully in for 10 seconds. The

Online LED will begin glowing in a cyclical order: GREEN-

AMBER-RED, indicating it is going into “Program mode”.

3. The Back-UPS will then indicate the current

sensitivity, as shown in the Transfer Voltage and Sensitivity

Adjustment table below.

4. To select the LOW sensitivity setting, press the ON/OFF

push button until the LED begins

flashing GREEN.

5. To select the MEDIUM sensitivity setting, press the ON/

OFF push button until the LED begins flashing RED.

6. To select the HIGH sensitivity setting, press the ON/OFF

push button until the LED begins

flashing AMBER.

7. To exit Programming mode, once sensitivity is set, wait

approximately 5 seconds, and all of the LED indicators will

be off (unlit).

Indicators

Flashing Sensitivity Setting Input Voltage Range

(For Utility Operation) When to Use

Green

Flashing

LOW 88-142 Input voltage is extremely low or

high.

Not recommended for computer

loads.

Red Flashing MEDIUM

(factory default)

92-139 Back-UPS frequently goes on

battery.

Amber

Flashing

HIGH 96-136 Connected equipment is

sensitive to voltage

fluctuations.

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	BE350G
Vægt:	3640 g
Opbevaringstemperatur (T-T):	-15 - 45 °C
Driftstemperatur (T-T):	0 - 40 °C
Dimensioner (BxDxH):	159 x 279 x 89 mm
Udgangseffekt:	200 W
Certificering:	cUL Listed,FCC Part 15 Class B,FCC Part 68,NOM,UL 1778,UL 497A,UL 498, RoHS
LED-indikatorer:	Ja
Kabellængde:	1.52 m
Opladningstid for batteri:	16 t
Indgangsfrekvens:	60 Hz
I/O-porte:	6x NEMA 5-15R
Input forbindertype:	NEMA 5-15P
Nominel udgangsspænding:	120 V
Nominel indgangsspænding:	120 V
Output strømkapacitet (VA):	0.35 kVA
Typisk backup tid ved halv styrke:	5.6 min.
Typisk backup tid ved fuld styrke:	0.4 min.