APC BE400-GR-OC Manual

APC Uafbrydelig strømforsyning (UPS) BE400-GR-OC

Læs gratis den danske manual til APC BE400-GR-OC (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om APC BE400-GR-OC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Back-UPS ES 400/550/700

User’s Guide

1Connect Battery

For safety, the Back-UPS ES is shipped with one battery wire disconnected. The Back-UPS ES will not operate until the wire is connected to the touch

safe battery terminal.

NOTE: Small sparks may occur during battery connection. This is normal.

TURN the Back-UPS ES over and

slide the battery compartment

cover off of the battery housing.

1 2 3

LIFT the battery out of the compartment

and connect the black wire to the

negative (-) battery terminal. Ensure the

batteries are installed as shown below.

Slide the battery compartment cover

back onto the battery housing.

Place the Back-UPS ES to avoid:

- Direct sunlight

- Excessive heat

- Excessive humidity or contact with ﬂuids

Plug the Back-UPS ES power cord directly into a wall outlet; not a

surge protector or power strip. The wall outlet should be located near

the equipment and be easily accessible.

Connect Modem / Phone / DSL / Fax / 10/100 Base- T/HPNA to

Surge Protection.

The Back-UPS protects a single line (2-wire) phone (including Digital

Subscriber line - DSL), Home Phoneline Networking Association (HPNA)

type equipment, modem, 10/100. Base-T Ethernet, or fax machines from

surges when connected through the UPS as shown in the drawing below.

Note: Telephone Cable OR Network Cable should be connected to Surge

Protection ports. Do not connect the UPS surge protection ports to both

Telephone and Network System cables at the same time.

Connect Computer Cable (This is applicable for 550/700 only)

The supplied cable and software provide automatic ﬁle saving and

shutdown of the operating system in the case of a sustained power outage.

Connect the cable to the Data Port of the Back-UPS ES. Connect the other

end of the cable to the USB port on your computer. The software will

automatically ﬁnd the USB Port of your computer.

2 Connect Equipment

Surge Protection Only

These outlets provide full-time protection from surges even if

the Back-UPS ES is switched OFF. Plug your printer, fax

machine, scanner, or other peripherals that do not need

battery power into these outlets.

Battery Backup

Surge Protection

These outlets are powered whenever the Back-UPS ES is

switched ON. During a power outage or other utility

problems (brownouts, over-voltages), these outlets will be

powered for a limited time by the Back-UPS ES. Plug your

computer, monitor, and two other data-sensitive devices

(external disk or tape drive) into these outlets.

DATALINE OUTPUT

TO COMPUTER USB

FROM WALL JACK

PORT (BACK-UPS ES 550

AND ES 700 ONLY)

TO DSL MODEM,

PHONE, NETWORK

CIRCUIT BREAKER

PUSH TO RESET

(10/100 Base-T)

3Power On and

Install Software

Press the ON/OFF switch to power the unit

ON.

A single short beep and the green “Power On”

indicator conﬁrms that Back-UPS ES is on and

ready to provide protection.

The Back-UPS ES should charge for at least

16 hours to ensure sufﬁcient runtime. The unit

is being charged whenever it is connected to

utility power, whether the unit is turned ON or

OFF.

Install the PowerChute Personal

Edition software (This is applicable for

550/700 only.)

Place the PowerChute Personal Edition CD-

ROM into your computer and follow the

installation instructions on the screen.

Status Indicators

The Back-UPS ES indicates operating status using a combination of visual and audible indicators.

Use the following table to identify the status of the Back-UPS ES.

Status Visual Indications

(Power On - Green)

(Replace Battery - Red)

Audible Indication Alarm Terminates

When

Power On

- UPS is supplying conditioned

utility power to the load.

Power On LED - ON None Not applicable.

On Battery

- UPS is supplying battery

power to the load connected to the Battery

outlets.

Power On LED - ON (off

during beep)

Beeping 4 times every

30 seconds

UPS transfers back to

Power On operation, or

when UPS is turned off.

Low Battery Warning

- UPS is supplying

battery power to the load connected to the

Battery outlets and the battery is near

exhaustion.

Power On LED - ﬂashing Rapid beeping (every

1/2 second)

UPS transfers back to

normal operation, or

when UPS is turned off.

Replace Battery

- Battery is in need of

charging or is at the end of its usual life and

must be replaced.

Power On and Replace

Battery LEDs - Flashing

(alternating)

Constant tone UPS turned off with the

power switch.

Battery Disconnected

- The battery is

disconnected or bad battery.

Replace Battery LED -

ﬂashing

Constant tone UPS turned off with the

power switch.

Overload Shutdown

- During On Battery

operation a battery power supplied outlet

overload was detected.

None Constant tone UPS turned off with the

power switch.

Sleep Mode

- During On Battery operation

the battery power has been completely

exhausted and the UPS is waiting for utility

power to return to normal.

None Beeping once every 4

seconds.

Utility power is restored,

or if utility power is not

restored within 32

seconds, or the UPS is

turned off.

See the Troubleshooting section for additional assistance.

All other trademarks are property of their respective owners.

APC, Back-UPS and PowerChute are registered trademarks of American Power Conversion Corp.

AC LINE

CORD

POWER ON/

REPLACE BATTERY

INDICATOR

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	BE400-GR-OC
Vægt:	5400 g
Produktfarve:	Sort
Pakkevægt:	5600 g
Batteriteknologi:	Blybatterier (VRLA)
Opbevaringstemperatur (T-T):	0 - 40 °C
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 95 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 40 °C
Dimensioner (BxDxH):	230 x 285 x 86 mm
Støjniveau:	45 dB
Udgangseffekt:	240 W
Certificering:	CE, GOST, NEMKO
Filtrering:	Ja
LED-indikatorer:	Ja
Pakkens dimensioner (BxDxH):	300 x 366 x 132 mm
Mac kompabilitet:	Ja
Opladningstid for batteri:	16 t
Driftshøjde:	0 - 15000 m
Ikke-drift højde:	0 - 15000 m
Lydalarmer:	Ja
Nominel udgangsspænding:	230 V
Nominel indgangsspænding:	230 V
Output-forbindere:	4 x CEE 7\n4 x CEE 7
Overspænding energivurdering:	310 J
Output strømkapacitet (VA):	0.4 kVA
Udgangsspænding note:	230