APC BE450G-LM Manual

APC Uafbrydelig strømforsyning (UPS) BE450G-LM

Læs gratis den danske manual til APC BE450G-LM (6 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om APC BE450G-LM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

Back-UPS® ES 450/550G

User Guide

Connect Battery

Equipment

Turn the Unit On

Surge Protection

These outlets provide full-time protection from surges even if the

Back-UPS ES is switched OFF. Plug your printer, fax machine,

scanner, or other peripherals that do not need battery power into these

outlets.

Battery Back-up +Surge Protection

These outlets are powered whenever the Back-UPS ES is

switched ON. During a power outage or other utility problems

(brownouts, over-voltages), these outlets will be powered for a

limited time by the Back-UPS ES. Plug your computer,

monitor, and other peripheral devices into the outlets.

Press the ON/OFF switch turn the unit ON.

A single short beep and the green “Power On” indicator confirms

the Back-UPS ES is on and ready to provide protection.

The Back-UPS ES should charge for at least 16 hours to ensure

sufficient runtime. The unit is being charged whenever it is

connected to utility power, whether the unit is turned ON or OFF.

If the red Building Wiring Fault indicator (located on the end near

the power cord) is lit, your building wiring presents a shock hazard

that should be corrected by a qualified electrician.

Install the PowerChute Personal Edition software.

Place the PowerChute CD into the computer and following the

installation instructions on the screen.

.apc.com

The Back-UPS ES indicates operating status using a combination of visual and audible

indicators. Use the following table to identify the status of the Back-UPS ES.

Status

Visual Indications

(Power On - Green)

(Replace Battery -

Red)

Audible Indication Alarm Terminates When

Power On - UPS is supplying

conditioned utility power to the load.

Power On pushbutton

- ON (lit)

None Not applicable.

On Battery - UPS is supplying

battery power to the load connected

to the Battery outlets.

Power On pushbutton

- ON (off during beep)

Beeping 4 times every

30 seconds

UPS transfers back to

Power On operation, or

when UPS is turned off.

Low Battery Warning - UPS is

supplying battery power to the load

connected to the battery outlets, and

the battery is near exhaustion.

Power On indicator is

flashing

Rapid beeping (every

1/2 second)

UPS transfers back to

normal operation, or when

UPS is turned off.

Replace Battery - The battery is

disconnected.

The battery is in need of charging, or

is at the end of its usual life and must

be replaced.

Replace Battery

indicator is Flashing

Power On and

Replace Battery

indicators - flashing

(alternating)

Constant tone

UPS is turned off with the

power switch.

Overload Shutdown - During On

Battery operation a battery power

supplied outlet overload was

detected.

None Constant tone UPS is turned off with the

power switch.

Sleep Mode - During On Battery

operation the battery power has

been completely exhausted and the

UPS is waiting for utility power to

return to normal.

None Beeping once every 4

seconds

Utility power is restored,

or if utility power is not

restored within 32

seconds, or the UPS is

turned off.

Building Wiring Fault - Your

building wiring presents a shock

hazard that should be corrected by a

licensed electrician.

Building Wiring Fault

LED (red) - ON

None UPS is unplugged, or

UPS is plugged into a

properly wired outlet.

Status Indicators

For safety, the Back-UPS ES is shipped with one battery wire disconnected. The UPS will not operate until the wire is connected to the touch-safe battery terminal.

NOTE: Small sparks may occur during battery connection. This is normal.

 Turn the Back-UPS ES over and press in the

release tab. Slide the plastic battery cover off of the

Back-UPS.

 Insert the battery back into the compartment.

Slide the plastic battery cover until the release tab

locks into place.

 Connect the battery wire firmly to the

battery terminal.

Connect

Connect Modem / Phone / DSL / Fax

The Back-UPS protects a single line (2-wire) phone (including Digital Subscriber Line - DSL),

Home Phoneline Networking Association (HPNA) type equipment, modem, or fax machines

from surges when connected through the UPS as shown in the drawing below.

Place the Back-UPS ES to avoid:

- Direct sunlight

- Excessive heat

- Excessive humidity or contact with fluids

Plug the Back-UPS ES power cord directly into a wall outlet; not into a surge protector

or power strip.

Connect Computer Cable

The supplied cable and software provide automatic file saving and shutdown of the operating

system in the case of a sustained power outage.

Connect the cable to the Data Port of the Back-UPS ES. Connect the other end of the cable to

the USB port on your computer. The software will automatically find the computer’s USB Port.

and Install the Software

Transfer Voltage and

Sensitivity Adjustment

(Optional)

To adjust the transfer voltage:

1. Plug the Back-UPS into the utility power source. The Back-UPS

will be in “Standby mode” (no indicators are lit).

2. Press the ON/OFF push button fully in for 10 seconds. The

Online LED will begin glowing in a cyclical order: GREEN-

AMBER-RED, indicating it is going into “Program mode”.

3. The Back-UPS will then indicate the current

sensitivity, as shown in the Transfer Voltage and Sensitivity

Adjustment table below.

4. To select the LOW sensitivity setting, press the ON/OFF push

button until the LED begins

flashing GREEN.

5. To select the MEDIUM sensitivity setting, press the ON/OFF

push button until the LED begins flashing RED.

6. To select the HIGH sensitivity setting, press the ON/OFF push

button until the LED begins

flashing AMBER.

7. To exit Programming mode, once sensitivity is set, wait

approximately 5 seconds, and all of the LED indicators will be

off (unlit).

Indicators

Flashing Sensitivity Setting Input Voltage Range

(For Utility Operation) When to Use

Green

Flashing

LOW 88-142 Input voltage is extremely low or

high.

Not recommended for computer

loads.

Red Flashing MEDIUM

(factory default)

92-139 Back-UPS frequently goes on

battery.

Amber

Flashing

HIGH 96-136 Connected equipment is

sensitive to voltage

fluctuations.

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	BE450G-LM
Bredde:	305 mm
Dybde:	178 mm
Højde:	84 mm
Vægt:	5910 g
Produktfarve:	Sort
Skærmtype:	LED
Pakkevægt:	6500 g
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Kompakt
Opbevaringstemperatur (T-T):	-15 - 45 °C
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Relativ luftfugtighed ved opbevaring (H-H):	5 - 95 %
Antal USB 2.0-porte:	1
Driftstemperatur (T-T):	0 - 40 °C
Støjniveau:	45 dB
Udgangseffekt:	257 W
Certificering:	cUL, FCC p15 B, FCC p68, NOM, UL 1778, UL 497A, UL 497B
LED-indikatorer:	Ja
Kabellængde:	1.52 m
Pakkens dimensioner (BxDxH):	438 x 140 x 241 mm
Bæredygtighedscertifikater:	RoHS
Driftshøjde:	0 - 3000 m
Ikke-drift højde:	0 - 15000 m
Indgangsfrekvens:	50/60 Hz
Lydalarmer:	Ja
Nominel udgangsspænding:	120 V
Nominel indgangsspænding:	120 V
Modem-porte (RJ-11):	1
AC udgange, antal:	8 AC stikkontakt(er)
AC stikkontakt typer:	NEMA 5–15R
Indgående driftsspænding (maks.):	- V
Output strømkapacitet (VA):	0.45 kVA
Indgående driftsspænding (min.):	- V
Udgangs driftsspænding (min.):	- V
Udgangs driftsspænding (maks.):	- V