APC BE700G-UK Manual

APC Uafbrydelig strømforsyning (UPS) BE700G-UK

Læs gratis den danske manual til APC BE700G-UK (4 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 16 anmeldelser. Har du et spørgsmål om APC BE700G-UK, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Back-UPS® ES 550/700 Operation

Caution

• For safety, the Back-UPS ES is shipped with one battery wire disconnected. Small sparks may occur during battery

connection.

• Do not install the unit in direct sunlight, in excessive heat or humidity, or in contact with fluids.

• Connect the power cord directly to a wall outlet; not a surge protector or power strip. The outlet

must be located near the equipment and easily accessible.

Connect the Battery

Overview

Turn on the Back-UPS

Press the ON/OFF switch to turn the unit ON. A single short beep and the green “Power On” indicator confirms that

Back-UPS ES is on and ready to provide protection. The UPS will automatically perform a self-test when power is

applied to the unit, the green LED will flash during the self-test.

Note: Prior to first use, charge the Back-UPS for at least 16 hours to ensure sufficient runtime. The unit is charging

whenever it is connected to utility power, whether the unit is turned ON or OFF.

Master Outlet—Connect a master device, such as a computer. See

“Using the power-saving outlets” on page 2.

Battery Backup and Surge Protection—These outlets receive

power whenever the unit is ON. During a power outage or other

utility problems (brownouts, over-voltages), these outlets will

receive power from the unit for a limited time. Connect a computer,

monitor, and two other data-sensitive devices into these outlets.

Note that one of these outlets is the Master outlet. See “Using the

power-saving outlets” on page 2.

Controlled Outlets—Connect peripheral devices. See “Using the

power-saving outlets” on page 2.

Surge Protection—These outlets provide full-time protection from

surges even if the unit is OFF, but will only supply power when the

unit is ON. Connect a printer, fax machine, scanner, or other

peripherals that do not need battery power during power outages.

Note that if the power-saving feature is enabled, three of these

outlets are controlled by the Master outlet.

Data Port—Use the supplied RJ45/USB cable to connect the Back-

UPS unit to a computer to install the software. See “Install the

PowerChute® Personal Edition software” on page 2.

Circuit Breaker—Push to re-set the circuit breaker.

Modem/Phone/Fax—Connect a DSL or dial-up modem, phone,

fax machine, or 10/100 Base-T ethernet equipment. Note: Do not

connect the UPS telephone protection ports to both the

telephone and network system cables at the same time.

Wall outlet—Connect the unit to a data line wall outlet.

bu034a

bu035a

bu036a

bu052a

Back-UPS ES 550 & 750 2

Install the PowerChute® Personal Edition software

Using the supplied USB cable, connect the data port of the unit to the USB port on a computer. Install the

PowerChute Personal Edition software using the enclosed CD.

Power-saving Master and Controlled Outlets

To conserve electricity, configure the Back-UPS to recognize a Master device, such as a desktop computer or an A/V

receiver, and Controlled peripheral devices, such as a printer, speakers, or a scanner. When the Master device goes

into Sleep or Standby mode, or turns OFF, the Controlled device(s) will shut down as well, saving electricity.

Using the power-saving outlets

Note: The Back-UPS ships with the power saving feature DISABLED. To use this feature, the outlets

must be enabled.

Enable the power-saving outlets. Press and hold MASTER ENABLE for 2 seconds. The unit will beep to indicate the

feature is enabled. The green LED above the M ASTER ENABLE button will illuminate.

Disable the power-saving outlets. Press and hold MASTER ENABLE for two seconds. The unit will beep to

indicated the feature is disabled. The green LED above the MASTER ENABLE button will darken.

Setting the threshold

The amount of power used by a device in Sleep or Standby mode varies between devices. It may be necessary to

adjust the threshold at which the Master outlet signals the Controlled outlets to shut down. When the threshold is set,

the power-saving outlets are enabled.

1.Ensure a master device is connected to the Master outlet. Put that device into Sleep or Standby mode, or turn it

OFF.

2.Press and hold the Master Enable button for six seconds. After the first 2 seconds the unit will beep, continue

holding the button down until the unit three beeps times in a row. Release the Master Enable button.

The Back-UPS unit will now recognize the threshold level of the Master device and save it as the new threshold

setting.

Status Indicators

LED Visual Indicator Audible Alarm Action

Power On - UPS is supplying conditioned utility

power to the load.

Green LED - ON None Not applicable.

On Battery - UPS is supplying battery power to the

load connected to the Battery outlets.

Green LED - ON (off

during beep)

Beeping 4 times

every 30 seconds

UPS transfers back to Power On

operation, or when UPS is

turned off.

Low Battery Warning - UPS is supplying battery

power to the load connected to the Battery outlets and

the battery is near exhaustion.

Green LED - flashing Rapid beeping (every

1/2 second)

UPS transfers back to normal

operation, or when UPS is

turned off.

Replace Battery is in need of charging or is at the end

of its usual life and must be replaced

Green/Red alternating

LED - flashing

Constant tone UPS turned off with the power

switch.

Battery Disconnected - The battery is disconnected or

bad battery.

Red LED - flashing Constant tone UPS turned off with the power

switch.

Overload Shutdown - During On Battery operation a

battery power supplied outlet overload was detected.

None Constant tone UPS turned off with the power

switch.

Sleep Mode - During On Battery operation the battery

power has been completely exhausted and the UPS is

waiting for utility power to return to normal.

None Beeping once every 4

seconds.

Utility power is restored, or if

utility power is not restored

within 32 seconds, or the UPS is

turned off.

Master Function Enabled Master Enable LED -

None

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	BE700G-UK
Vægt:	6930 g
Produktfarve:	Sort
Pakkevægt:	7840 g
Opbevaringstemperatur (T-T):	-15 - 45 °C
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 95 %
Driftstemperatur (T-T):	0 - 40 °C
Dimensioner (BxDxH):	224 x 311 x 89 mm
Udgangseffekt:	405 W
Certificering:	UL, FCC, CE, C-Tick, RoHS
Kabellængde:	1.83 m
Pakkens dimensioner (BxDxH):	279 x 400 x 127 mm
Opladningstid for batteri:	16 t
Driftshøjde:	0 - 9000 m
Indgangsfrekvens:	47/63 Hz
Nominel udgangsspænding:	230 V
Nominel indgangsspænding:	230 V
Output-forbindere:	8 x BS 1363
Overspænding energivurdering:	310 J
Output strømkapacitet (VA):	0.7 kVA
Typisk backup tid ved halv styrke:	13.3 min.
Typisk backup tid ved fuld styrke:	3.5 min.
Udskiftningsbatteri:	RBC17