APC BE850M2 Manual

APC Uafbrydelig strømforsyning (UPS) BE850M2

Læs gratis den danske manual til APC BE850M2 (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 19 anmeldelser. Har du et spørgsmål om APC BE850M2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Inventory

Safety and General Information

Inspect the package contents upon receipt. Notify the carrier and

dealer if there is any damage.

SAVE THESE INSTRUCTIONS - This section contains important

instructions that should be followed during installation and maintenance

of the UPS and batteries. Failure to follow these instructions can result

in equipment damage.

Connect the Battery

The Back-UPS is shipped with one battery cable disconnected.

Connect Equipment

Note: USB charging ports are only available on the BE850M2 and the BE850M2-LM..

Turn On the Back-UPS

Press the POWER button. It will illuminate green and a single short beep indicating that the

Back-UPS is on and providing protection for connected equipment.

The Back-UPS battery will charge regardless of whether the Back-UPS is switched on or off

as long as it is connected to AC power. The UPS will have full runtime capability after the

initial 24-hour charging period, connected to AC power.

If the red Building Wiring Fault indicator (located on the end near the power cord) is lit, your

building wiring may present a shock hazard that should be corrected by a qualified

electrician.

Turn Off the Back-UPS

Press the POWER button for at least 2 seconds. At the first beep, release the button and the

UPS will turn off. A 2 second delay has been added to mitigate unintentional contact with the

POWER button.

Quick Mute

The Back-UPS is able to temporarily mute user correctable alarms such as: On Battery,

Battery disconnected and Overload.

During such alarms, a short press (less than 2 seconds) of the POWER button will

temporarily mute the alarm until the condition has been reset. A short double beep will

confirm that Quick Mute has been activated. Pressing the POWER button for more than 2

seconds will turn off the UPS.

Other critical events such as Battery replacement and Charger notification can not be

temporarily muted. The unit in these cases must be turned off.

On Battery Indicator Modes

With the UPS turned on, configuring the On Battery Indicator modes below is done by

holding down the POWER button and waiting for the third beep. At the third beep, the

POWER button will cycle red / green. Release the POWER button and its color will indicate

the mode the UPS is in. Press the POWER button to cycle through each mode. See the table

below for the 3 mode selection colors. Once the mode has been selected, wait 5 seconds and

the setting will be committed to the UPS.

PowerChute™ Personal Edition Software

Overview

Use PowerChute Personal Edition software to configure the UPS settings. During a power

outage, PowerChute will save any open files on your computer and shut it down. When

power is restored, it will restart the computer.

Note: PowerChute is only compatible with a Windows operating system. If you are using

Mac OSX, use the native shutdown feature to protect your system. See the documentation

provided with your computer.

Installation

Use a USB cable to connect the Data port on the rear panel of the UPS to the USB port on

your computer. On the computer, go to www.apc.com/tools/download. Select “Software

Upgrades - PowerChute Personal Edition” in the “Filter by Software/Firmware” drop down

menu. Select the appropriate operating system. Follow directions to download the software.

Status Indicators

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Connect the UPS power cable directly to a wall outlet.

• The UPS is intended for indoor use only.

• Do not operate the UPS in direct sunlight, in contact with fluids, or where there is excessive dust

and humidity.

• Be sure the air vents on the UPS are not blocked. Allow adequate space for proper ventilation.

Failure to follow these instructions will result in death or serious injury.

CAUTION

RISK OF HYDROGEN SULPHIDE GAS AND EXCESSIVE SMOKE

• Battery must be replaced when they reach end of service life.

• Batteries must be replaced when the unit indicates battery replacement is necessary.

• When replacing batteries, replace with the same number and type of batteries originally installed in

the unit.

Failure to follow these instructions could result in minor or moderate injury and

equipment damage.

 Remove the

“Stop! Connect the Battery” label

that covers the outlets.

 Press the battery compartment cover release

tabs located on the underside of the unit. Slide

the battery cover off.

 Connect the battery cable securely to the

battery terminal. It is normal for small sparks to

be seen when the battery cable is connected to

the battery terminal.

 Reinstall the battery compartment cover.

Be sure that the release tabs lock into place.

Feature Function Suggested Use

Battery Backup + Surge

Protection Outlets

• Receive power from the

battery for a limited period

of time when a power

outage, or brownout

condition occurs.

• Provide protection from

power surges or spikes.

Connect a computer, monitor and

other critical peripheral devices

that need to remain on during

power outages or AC problems.

Surge Protection Outlets • Provide protection from

power surges or spikes.

Connect non-critical peripheral

devices (such as printer, scanner,

etc.) that do not need to remain on

during power outages or AC

problems.

USB charging ports

(BE850M2/850M2-LM only)

• Provide power when the unit

is on AC and on battery.

Charge USB devices

bu446b

bu447b

bu448b

bu449b

bu450b

USB

Charging

Ports

Battery Backup + Surge

Protection Outlets

Surge Protection

Outlets

bu451b

POWER

Button

bu452b

Building

Wiring

Fault

USB Data Port

(PowerChute)

AC Power

Inlet

Circuit

Breaker

Mode Visual

Indicator Audible Indicator Mode Selection

Color

Quiet Alarm

(default)

The POWER

button is solid

green and flashes

twice every 2

seconds until

Low Battery

notification

where it will

flash green in

rapid succession.

No alarm until Low Battery

notification where the alarm beeps

twice every 30 seconds

Flashing green

No Alarm No alarm while the UPS is On

Battery Flashing red

Full Alarm Alarm sounds 4 beeps every 30

seconds until Low Battery

notification where the alarm beeps

every half second. As the UPS shuts

down, it sounds one beep every 4

seconds

Flashing amber

Status Power Button

illumination

Audible

Indicator On

Audible Indicator

Terminates

Power On

The Back-UPS is supplying AC

power to connected equipment.

Solid green None N/A

On Battery

Back-UPS supplying battery power

to battery backup outlets.

Solid green and

flashes twice

every 2 seconds. The audible

alarm depends

on the On

Battery

Indicator mode

setting. See the

On Battery

Indicator

Modes section

for full details.

- Using Quick Mute

- Beeping stops when AC

power is restored or the

Back-UPS is turned off.

Applies only to modes

where the on battery

alarm is audible.

Low Battery notification

The Back-UPS is supplying battery

power to the battery backup outlets

and the battery is near a total

discharge state.

Flashes green in

rapid succession.

Low Battery shutdown

The battery has been completely

discharged while the Back-UPS is

on battery, the UPS will shut down.

None - AC power is restored

- AC is not restored

within 32 seconds

- The Back-UPS is turned

off.

Sleep Mode

The UPS has shut down and will

“awaken” once AC power is

restored

None None N/A

Replace Battery

• The battery is disconnected.

• The battery needs to be charged,

or replaced.

• Flashes red

only.

• Alternates

green-red

• Constant tone

- Back-UPS is turned off

- If the battery is

disconnected, connect

the battery or use Quick

Mute

On Line Overload

Condition occurs when the UPS is

on AC power and the connected

load exceeds the power output of

the UPS. If overload persists for an

extended period of time, the UPS

will enter Overload Shutdown.

Solid amber Constant tone - Using Quick Mute

- Load removed from the

UPS

- Load exceeds circuit

breaker and the UPS

turns off

Overload Shutdown

An overload condition has occurred

in one or more of the battery backup

outlets while operating on battery

power. This also occurs if On Line

Overload persists for an extended

period of time.

None Constant tone Back-UPS is turned off

USB Detected Fault

A short circuit has been detected or

an error has occurred.

Alternates

green-amber

None N/A

User Manual Back-UPS™ BE850M2/850M2-LM, BN900M/900M-CA

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	BE850M2
Bredde:	327 mm
Dybde:	105 mm
Højde:	139 mm
Vægt:	4100 g
Brugervejledning:	Ja
Produktfarve:	Sort
Pakkevægt:	4400 g
Pakkedybde:	168 mm
Pakkebredde:	416 mm
Pakkehøjde:	196 mm
USB-port:	Ja
Formfaktor:	Kompakt
Opbevaringstemperatur (T-T):	-15 - 45 °C
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 95 %
Antal USB 2.0-porte:	2
Driftstemperatur (T-T):	0 - 40 °C
Kabler inkluderet:	USB kabel
Støjniveau:	45 dB
Udgangseffekt:	450 W
LED-indikatorer:	Ja
Kabellængde:	1.52 m
Batterilevetid (maks.):	5 År
Antal understøttede batterier:	1
Opladningstid for batteri:	8 t
Bæredygtighedscertifikater:	ENERGY STAR
Driftshøjde:	0 - 3000 m
Ikke-drift højde:	0 - 15000 m
Indgangsfrekvens:	50/60 Hz
Batteriets kapacitet:	84 VAh
Lydalarmer:	Ja
Strømstik:	NEMA 5-15P
AC udgange, antal:	9 AC stikkontakt(er)
AC stikkontakt typer:	NEMA 5–15R
Overspænding energivurdering:	354 J
Indgående driftsspænding (maks.):	139 V
Output strømkapacitet (VA):	0.85 kVA
Indgående driftsspænding (min.):	92 V
Udgangs driftsspænding (min.):	120 V
Udgangs driftsspænding (maks.):	120 V
UPS topologi:	Standby (offline)
Strøm (maks.):	5 A
Regulering af udgangsfrekvens:	50 - 60 Hz
Holdetid (maks.):	10 ms
Beskyttelse ved overspænding:	Ja
Holdetid (min.):	6 ms
Hørbare alarmtilstande:	Alarm when on battery,Low battery alarm,Overload alarm
Koldstart:	Ja
EMI/RFI støjfiltrering:	Ja