APC BH500 Manual

APC Uafbrydelig strømforsyning (UPS) BH500

Læs gratis den danske manual til APC BH500 (4 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 69 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 35 anmeldelser. Har du et spørgsmål om APC BH500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTALLATION

.apc.com

Back-UPS HS 500

User’s Manual

990-9236 3/04

3Remove Battery (if wall-mounting - if not proceed at Step 5)

0 - 40oC (32 - 104 oF)

1Placement 2Remove Connector Cover

Disconnect battery

wires from battery.

Remove battery.

Press cover release

tab (one each side)

and remove cover.

Caution: To prevent damage to the ribbon cable (not shown)

that connects the cover to the UPS, replace the cover after

removing the battery. Do not disconnect the ribbon cable

from the cover or the UPS.

Press the outlet cover release

tab (one each side); and pivot

cover off the unit.

Phone Line Out

4Mount Back-UPS (optional)

Wall Anchor

Mounting

Hole

Wall

5Connect/Install Battery, Install Battery Cover

Install battery cover.

Connect and install

the battery.

Press the outlet cover

release tab (one each

side); and pivot cover

off the unit.

6Connect Cable Modem,

Circuit Breaker

Push to Reset

Cable Out

Input:

230V~, 2.2A, 50-60Hz

Cable In

From Cable Provider

(Phone, Internet,

and/or CATV; or

DSS)

To Cable Modem,

VCR, DSS or TV

Cable Box

7Connect Phone Line

LAN

NetworkModem/Phone/Fax

RJ-45

Connectors

(can accept RJ-11)

RJ-45

Connectors

Phone Line In

(Standard or

DSL)

From Network Device

(or Computer Using a

Crossover Cable)

From Modem

DSS or CATV Receiver

8 10 Install Connector Cover

(optional)

or DSL to Surge

Connect Network

Equipment

To Hub

Router

11 Connect to Power Source and Switch on UPS Power

Connect Equipment Power Cords

Hub

or Router

Modem

Network Device

Output 1

Output 2

Output 3

to Surge Protection Protection (optional)

Align the holes in the

cover with the connector

cover release tabs (one

each side) and lower

connector cover.

7 AMP

The line cord used for this connection is supplied

by the user.

NOTE: APC recommends your network equipment

(computer, modem, router, hub, or other networked

devices) be completely installed, configured, and

tested prior to adding this UPS to the network.

Figure 2. InstallShield Welcome Screen

4. The software will then display the Licence Agreement (Figure 3). Please

read the Agreement and accept the terms by clicking Yes. To decline the

Agreement, click No - the software will not install.

Figure 3. InstallShield Licence Agreement Screen

If Autoplay is enabled on your computer, the software on the CD-ROM will

automatically start the installation program.

If Autoplay is not enabled on the computer, proceed as follows:

1. On the computer desktop of the display, double-click on My Computer, or

start Windows Explorer to locate the computer’s CD-ROM drive icon.

2. Double-click on the CD-ROM drive icon and then double-click on the

setup.exe icon. The software will start and display the InstallShield

Wizard Screen (Figure 1). The software will begin the installation

process. To stop the installation, click Cancel.

Figure 1. InstallShield Wizard Screen

3. After about 4 seconds, the software will display the Welcome Screen

(Figure 2). To continue, click Next. To cancel the installation, click

Cancel.

There are six status indicators (lights) on the front panel of the Back-UPS (On Line, On Battery,

Overload, Replace Battery, TX/RX, and ACT/LNK).On Line (green) - is lit whenever AC utility power is

powering the outlets.

On Battery (yellow) - is lit whenever the battery of the

Back-UPS is supplying power to the equipment connected to

the outlets.

Four Beeps Every 30 Seconds - this alarm is

sounded whenever the Back-UPS is running On

Battery. Consider saving work-in-progress.

Overload (red) - is lit whenever power demand has

exceeded the capacity of the Back-UPS.

Continuous Tone - this alarm is sounded

whenever the Back-UPS outlets are overloaded.

Replace Battery (red) - is lit whenever the battery is

near the end of its useful life, or if the battery is not

connected (see above). A battery that is near the end of its

useful life has insufficient run-time and should be replaced.

Chirps for 1 Minute Every 5 Hours - this

alarm is sounded whenever the battery has failed

the automatic diagnostic test.

Continuous Beeping - this alarm is sounded

whenever a low battery condition is reached.

Battery run-time is very low. Promptly save any

work-in-progress and exit all open applications.

Shutdown the operating system, computer, and the

Back-UPS.

STATUS INDICATORS AND ALARMS

Back-UPS

0 0

Replace

Battery

OverloadOn Battery

On-Line

ACT/LNK

TX/RX

.apc.com

TX/RX (green) - is lit whenever the Back-UPS is

sending or receiving data over the network.

ACT/LNK (green) - is lit whenever the Back-UPS is

connected to equipment and is ready and waiting to send

or receive data.

TRANSFER VOLTAGE/SENSITIVITY ADJUSTMENT (Optional)

Circuit Breaker - the rocker-type circuit breaker switch

located on the bottom panel of the Back-UPS will trip if an

overload condition forces the Back-UPS to disconnect

itself from AC utility power. If the switch trips, disconnect

non-essential equipment. Reset the circuit breaker by

pushing it to the ON position.

Follow the

on-screen

instructions.

INSTALL AND SETUP SOFTWARE

In situations where the Back-UPS or connected equipment appears too sensitive to input voltage, it may be

necessary to adjust the transfer voltage. This is a simple task requiring use of the front panel pushbutton. It can

also be accomplished using the Configuration Page Screen in the supplied software (see Install and Setup

Software). To adjust the transfer voltage, proceed as follows:

1. Plug the unit into an AC utility power source; the Back-UPS will go into Standby Mode (no indicators lit).

2. Press the front panel pushbutton fully inward for 10 seconds. All indicators on the Back-UPS will flash to

acknowledge going into Programming Mode.

3. The Back-UPS will then indicate its current Sensitivity Setting, as shown in the following table.

4. To select the Low Sensitivity setting, press the pushbutton until the yellow indicator is flashing.

5. To select the Medium Sensitivity setting, press the pushbutton until the yellow and red indicators are

flashing.

6. To select the High Sensitivity setting, press the pushbutton until yellow and both red indicators are flashing.

7. To exit without changing the Sensitivity Setting, press the pushbutton until the green indicator is flashing.

8. Once in Programming Mode, if the pushbutton is not pressed within 5 seconds, the Back-UPS will exit

Programming Mode; all indicators will extinguish.

Indicators

Flashing

Sensitivity

Setting

Input Voltage

Range (for

utility

operation)

Use When

(yellow)

Low 160 - 278 Vac Input voltage is extremely low or high. Not

recommended for computer loads.

(yellow, and red)

Medium

(factory default)

180 - 266 Vac Back-UPS frequently goes On Battery

(recommended).

(yellow, red, and red)

High 196 - 256 Vac Connected equipment is sensitive to voltage

fluctuations.

5. The software will display the Choose Destination Location Screen (Figure

4). Select Browse to find a location, click Next to accept the system default

location, the system will then display the Setup Status Screen (Figure 5).

Click on Cancel to stop the installation.

Figure 4. Choose Destination Location Screen

Figure 5. Setup Status Screen

6. The software then displays the InstallShield Wizard Complete Screen (Figure 6). Select

Finish to quit the installation program..

Figure 6. InstallShield Wizard Complete Screen

7. To launch the program, go to the Start menu, select APC, then select APC Back-UPS HS

(Figure 7). Continued on the next page -

Figure 7. APC Software Startup Menu Selections

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	BH500

Har du brug for hjælp?

Hvis du har brug for hjælp til APC BH500 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Uafbrydelig strømforsyning (UPS) APC Manualer

APC E3MCBC10B Manual

6 August 2025

APC Back-UPS BE700G3 Manual

5 August 2025

APC GVSBPIT75 Manual

5 August 2025

APC GVLMBCA200K500H Manual

4 August 2025

APC E3SBPAR10K40F Manual

4 August 2025

APC BE650G2-GR Manual

4 August 2025

4 August 2025

4 August 2025

4 August 2025

4 August 2025

Uafbrydelig strømforsyning (UPS) Manualer

Nyeste Uafbrydelig strømforsyning (UPS) Manualer

ATen EC1000 Manual

28 September 2025

Riello SEP 1500 Manual

20 September 2025

Riello Dialog Vision Manual

20 September 2025

Panamax MB1000 Manual

4 September 2025

Panamax MB1500 Manual

4 September 2025

Akyga AK-ND-41 Manual

30 August 2025

CyberPower HSTP3T30KEBCWOB Manual

20 August 2025

Vorago UPS-400 Manual

20 August 2025

CyberPower RT33020KE Manual

20 August 2025

CyberPower Value2200EILCD Manual

20 August 2025