APC BX1000L Manual

APC Uafbrydelig strømforsyning (UPS) BX1000L

Læs gratis den danske manual til APC BX1000L (1 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om APC BX1000L, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

0 /201EN 990-9740A8 5

by Schneider Electric Industries S A S or their affiliated companies Al l . . . . other

trademarks are property of their respective owners .

1Safety and General Information

• This UPS is intended for indoor use only.

• Connect the UPS power cable directly to a wall outlet. Do not use surge protectors or extension

cords.

• When grounding canno t be verified, disconnect the equipment from the AC power ou tlet before

installing or connecting to other equipment. Reconnect the power co rd after all

connections are made.

• Servicing of batteries should be performed by Schneider Electric IT (SEIT) Customer Support only.

• Do not dispose of batteries in a fire. The batteries may explode.

• Do not open batteries. They contain an electrolyte that is toxic an d harmful to the skin and eyes.

2Placement and Powering On

Plug the Back-UPS power cord directly into a wall outlet, not into a surge protector

or power strip.

Connect the battery by pulling the battery handle up,

and th en pushing it into the unit.

Press the ON/OFF button to turn the unit on.

The green “Power On” indicator co nfirms that the Back-UPS is on and read y to

provide protectio n.

The Back-UPS should charge for at least 6 ho urs to ensure sufficient runtime.

The un it is being charged whenever it is connected to AC power, whether the unit

is turned ON or OFF.

Place the Back-UPS to avoid:

‧ Direct sunlight

‧ Excessive heat

‧ Excessive moisture

For safety, please place the unit on the floor.

5LED Condition

On Off On-line - The Back-UPS is supplying AC power to

the connected equipment

Constant Tone On Line Overload - The power being used by the

connected equipment has exceeded the capacity of the

unit. Disconnect some equipment.

Constant beeping Over-temperature alarm -

The unit is overheating

and will shut down if the temperature is not lowered.

Disconnect some of the connected equipment.

(Off during 4 beeps)

4 beeps repeated

every 30 seconds

On-Battery - The Back-UPS is supplying battery

power.

Flashing Rapid Beeping

(every 1/2 second)

Low Battery alarm - The Back-UPS has 2

minutes of runtime remaining.

Constant tone Bad Battery Detected - The battery needs to be

charged, or is at end of life. (See Battery Replacement.)

Off Short beep every

4 seconds

Low Battery Shutdown - During On Battery

operation the battery power was almost completely

exhausted, and the Back-UPS is waiting for AC power

to return to normal.

Constant Tone On Battery Overload - The connected equipment

requires more power than provided by the Back-UPS

battery. Unplug devices one at a time to remove

overload. If the problem is not corrected, contact SEIT

Technical Support

Constant Tone Charger Fault Detected -- Back-UPS has an

internal problem, and is no longer powering the load.

Contact SEIT Technical Support

Audible Alarm

Long beep every

4 seconds UPS has overheated and has sh ut down.

Unplug connected devices one at a time or

wait for a few hou rs for sy stem to cool down.

Over-temperature Protected - The Back-

Status Indicators

Warranty

User Guide

BX1000L-LMBack-UPS

SAVE THESE INSTRUCTIONS -This manual contains

important instructions that should be followed during

installation and maintenance of the UPS and batteries

Schneider Electric IT (SEIT) warrants its products to be free from defects in materials and workmanship for a

period of two years from the date of purchase. SEIT obligation under this warranty is limited to repairing or

replacing, at its sole discretion, any such defective products. This warranty does not apply to battery wear from

use, equipment that has been damaged by accident, negligence or misapplication or has been altered or modified

in any way. SEIT standard procedure is to replace the original unit with a factory reconditioned unit. Customers

who must have the original unit back due to the assignment of asset tags and set depreciation schedules must

declare such a need at first contact with an SEIT Technical Support representative. SEIT will ship the replacement

unit once the defective unit has been received by the repair department, or cross ship upon the receipt of a valid

credit card number. The customer pays for shipping the unit to SEIT. SEIT pays ground freight transportation

costs to ship the replacement unit to the customer. For full warranty information refer to www.apc.com.

Features

3ON/OFF button

LED status indicator

Battery connector

AC power inlet

Battery and surge protected outlets

Fuse

Fuse Replacement

A spare fuse is prov ided in every Back-UPS unit.

Once the input curren t exceeds 15A, the installed

fuse in every unit will interrupt the circuit to

safeguard connected equipment from excessive

input curren ts. Replace it using the spare fu se, or

with a fuse that h as similar input current rating.

Inspect the package contents upon receipt. Notify the

carrier and dealer if there is any damage.

™

Specifications

Input

Output

Protection

Battery

Physical

years. Environmental factors impact battery

life. Elevated temperatures, high humidity,

poor quality mains power, and frequent,

short duration discharges will shorten

battery life.

The battery typically lasts for three to five

The battery in the Back-UPS Series is not

user-replaceable. Contact SEIT Technical

Support for a list of authorized service

centers near you.

EMC

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

12V/7AH lead acid

4-6 Hours

8.2 kg

18 .2 cm x 13.0 cm x 32 .0cm

Voltage / Frequency 12 0 VAC / 60 Hz

Brownout Transfer /

Over-voltage Transfer

89VAC, typical /

145VAC, typical

UPS Capacity (total) 10 00VA/600W

Voltage On Battery 12 0 Vac rms

Frequency - On Battery

Transfer Time

AC Input

Type (maintenance-free)

Averag e Life

60 Hz ± 1Hz

6ms typical

Fuse

Typical Recharge Time

Net Weight

Dimensions (Hx Wx D)

Operational Features

Auto matic Voltage Regulation boo sts/t rims the AC voltage when it drops/exceeds safe lev els.

This allows th e equipmen t plugged into the unit to operate during lo w/h igh voltag e conditions,

conserving the battery power in the ev ent of a po wer cu t.

The Back-UPS will switch to battery power if th e input voltage level b ecomes too low/high for

the Automatic Voltage Regu lation to compensate, or if the AC p ower is distorted.

Automatic Voltage Regulation (AVR)

APC by Schneider Electric IT Customer

Support Worldwide

For country specific customer support, go to the APC by Schn idere Electric Web site w apc , w w. .com.

Troubleshooting and Service

1 act Schneider Electric stomer Support through the APC by. If the problem persists, cont IT (SEIT) Cu

Schneider Electric Web site, www.apc.com.

a. Note the model number and serial number . and the date of purchase The model and serial numbers

are located on the rear panel of the unit and are available through the LCD display on select models.

b. Call SEIT Customer Support and a technician will attempt to solve the problem over the phone.

If it is not possible, the technician will issue a Returned Material Authorization Number (RMA#).

c. If the unit is under warranty, the repairs are free.

d. Service procedures and returns may vary . internationally Refer to the APC by Schneider Electric

Web site for country specific instructions.

2. Prepare to troubleshoot the problem over the . , phone If this is not successful and the unit is still under

, warranty the SEIT Technical Support Representative will provide all necessary information to return the

unit for replacement .

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	BX1000L

Har du brug for hjælp?

Hvis du har brug for hjælp til APC BX1000L stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Uafbrydelig strømforsyning (UPS) APC Manualer

APC Smart-UPS SMT3000RMT2U Manual

30 Oktober 2025

APC E3MCBC10B Manual

6 August 2025

APC Back-UPS BE700G3 Manual

5 August 2025

APC GVSBPIT75 Manual

5 August 2025

APC GVLMBCA200K500H Manual

4 August 2025

APC E3SBPAR10K40F Manual

4 August 2025

APC BE650G2-GR Manual

4 August 2025

APC SP3OPT002 Manual

4 August 2025

APC SP3OPT003 Manual

4 August 2025

APC SP3OPT005 Manual

4 August 2025

Uafbrydelig strømforsyning (UPS) Manualer

Nyeste Uafbrydelig strømforsyning (UPS) Manualer

CyberPower ALT750EILCDRT1U Manual

6 December 2025

CyberPower OL1KRTHD Manual

5 December 2025

CyberPower OL3KRTHD Manual

3 December 2025

CyberPower OL750RTHD Manual

3 December 2025

CyberPower OL2K2RTHD Manual

2 December 2025

Atlantis Land HostPower 1102 Manual

28 November 2025

MKC MK-2000UPS Manual

6 November 2025

Tripp Lite SMART1500RMXL2U Manual

6 November 2025

CyberPower RB1290X2D Manual

2 Oktober 2025

ATen EC1000 Manual

28 September 2025