APC ER7SHELF Manual

APC Ikke kategoriseret ER7SHELF

Læs gratis den danske manual til APC ER7SHELF (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om APC ER7SHELF, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation 990–91450 Release date: 02/2021

Easy Rack 50 Kg Shelf Kit ER7SHELF

Kit Instructions

The 1U, 50 kg Accessory Shelf can be installed to the vertical mounting flanges in

an empty space in the Easy Rack to support your equipment.

ER7SHELF Inventory Tools Required (not provided)

50 Kg Shelf (1)

Torx® wrench

M6 x 12 Pan Head T30 Screw (8) Cage nut tool

Caged Nut M6 14/16 SWG (8)

Proper location in the rack for the cage nuts:

ns0014a

1. Locate the top and bottom U space on the vertical

mounting rails. Every third hole on the mounting rails

is numbered to indicate the middle of a U space.

2. Install the cage nuts on the interior of the vertical

mounting rail; then install the shelf.

CAUTION

FALLING EQUIPMENT HAZARD

Do NOT install cage nuts vertically with the tabs engaging the top and bottom of

the square hole.

Failure to follow these instructions can result in injury or equipment

damage.

APC by Schneider Electric

70 Mechanic Street

02035 Foxboro, MA

USA

www.apc.com

As standards, specifications, and design

change from time to time, please ask for

confirmation of the information given in this

publication.

reserved.

Easy Rack 50 Kg Shelf Kit ER7SHELF

Proper installation position for the cage nuts:

ns1768a

• Install cage nuts horizontally, with the tabs engaging

the sides of the square hole.

• Install the cage nuts on the interior of the vertical

mounting rail.

Install the cage nut:

gen0188a

1. From the inside of the rack, insert the cage nut into the

square hole.

2. Hook one tab of the cage nut assembly through the far

side of the hole.

3. Place the cage nut tool on the other side of the cage

nut and pull to snap into position.

Remove the cage nut:

1. Remove any attached screw.

2. Grasp the cage nut, squeeze the tabs on the sides, and push to release it from the square hole.

50 kg Accessory Shelf Dimensions:

The adjustable sliding rails on the 50 kg Accessory Shelf allow you to customize the depth from the

minimum of 635mm (25.0 in) when retracted to a maximum of 1045mm (41.14 in) when fully

extended.

Adjust the rails:

To extend the adjustable rails of the shelf:

1. Remove the four (4) M6 x 12 pan head T30

screws from the adjustable rails..

2. Pull the adjustable rails out to the required

depth.

3. Install the four (4) M6 x 12 pan head T30

screws to secure the adjustable rails in

their new location.

Install the 50 kg Accessory Shelf:

Install four (4) cage nuts (provided) to the two front vertical mounting rails as described above. Install

four (4) cage nuts (provided) to the inside of the two rear vertical mounting rails as described above.

At the front of the rack, attach four (4) M6 x 12 pan head T30 screws (provided) to the front of the

shelf and into the four (4) cage nuts you installed in the vertical mounting rails.

At the rear of the rack, install four (4) M6 x 12 pan head T30 screws (provided) to the adjustable rails

on the rear of the shelf and through the four (4) cage nuts installed in the vertical mounting rails. The

illustration below shows this installation process.

ns3209a

Front of rack Rear of rack

The Easy Racks in the illustration above are shown without doors or side panels for clarity.

2 990–91450

Produkt Specifikationer

Mærke:	APC
Kategori:	Ikke kategoriseret
Model:	ER7SHELF
Type:	Stativhylde
Bredde:	485 mm
Dybde:	632 mm
Højde:	32 mm
Antal pr. pakke:	1 stk
Produktfarve:	Sort
Pakkevægt:	6000 g
Pakkedybde:	710 mm
Pakkebredde:	580 mm
Pakkehøjde:	110 mm
Harmoniseret systemkode (HS):	85389099
Maksimal vægtkapacitet:	50 kg