APC SBP16KRMI4U Manual

APC Ikke kategoriseret SBP16KRMI4U

Læs gratis den danske manual til APC SBP16KRMI4U (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om APC SBP16KRMI4U, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

owned by Schneider Electric industries S.A.S American Power Conversion

Corporation, or their affiliated companies. All other trademarks are property

of their respective owners.

990-1530B

Note: Read the safety information sheet before installation.

Illustrations in this document may differ slightly from the actual hardware.

Attention: This product is for use in a controlled environment. Refer to product

specifications for environmental limits.

R MACK OUNTING

o Set SBP in the rack. If hardwiring is required, see Connecting Power

section before screwing into the rack.

W MALL OUNTING

o Whenever possible, attach one top screw and one bottom screw into a wall stud. If stud

mounting is not possible, use an expandable wall anchor. Screws are not included; .25” x

2” lag bolts are recommended.

T O ( SOWER PTION FOR MART-UPS RT SETUPS ONLY)

n Remove screw from the top and bottom rear of both the UPS and SBP. Install tie

brackets and reattach screws.

o Unscrew and remove top cover of the

UPS.

p Attach bracket to top of UPS and SBP.

q Reattach top cover of the UPS.

Note: The SBP5000RMI2U, when used in conjunction with an SURT3000XLI or SURT5000XLI UPS in a

tower configuration without an external battery pack (SURT192XLBP), is suitable for mounting on

concrete or other non-combustible smooth surfaces only.

U C SER ONFIGURABLE

Attention: When using an online UPS, put the UPS in automatic bypass mode before

rotating the SBP switch.

1. Normal: Power is directed from the utility outlet, through the Bypass Panel and UPS,

and to connected equipment. For use during normal UPS operation.

2. Test: Power supplied to the UPS is not output. Use when tests are being conducted on

the UPS, and connected equipment is not yet desired.

3. Bypass: Power from the utility outlet is filtered through the Bypass Panel, and to the

connected equipment. Use to bypass the UPS, when functioning improperly.

Note: While operating in ‘Test’ or ‘Bypass’ mode, power to the connected equipment is

not conditioned by the UPS. At this time, the “Equipment Protection Policy” is not valid.

I PDENTIFYING THE ANEL

Service Bypass Panels will differ. Refer to chart for unit specifications.

Note: HW= Hardwire

Service Bypass

Panel

Corresponding

UPS Systems

Bypass

Input

UPS

Input

UPS

Output

PDU

Panel

SBP3000RM2U 100-120V Smart-UPS

3kVA

L5-30P L5-30P L5-30R (2) 5-20R,

(6) 5-15R

SBP5000RMT2U 200/208/240V

Smart-UPS 3-4.5kVA

L6-30P L6-30P L6-30R (2) L6-20R,

(2) L6-30R

SBP5000RMI2U* 230V Smart-UPS

3-5kVA

C20/HW C19/HW C20/HW (2) C19,

(8) C13

SBP6KRMT2U** 200/208/240V

Symmetra 2-6kVA

L6-30P/

L6-30R/

L6-30P/

(1) L6-20R,

(2) L6-30R

SBP6KRMI2U 230V Symmetra

2-6kVA

HW HW HW (4) C19

SBP3000 100-240V Smart-UPS

3-5kVA with 30A HW

input/output

available

HW HW HW HW

SBP10KRMT4U 200/208/240V

Smart-UPS RT

7.5-10kVA

HW HW HW (3) L6-20R,

(3) L6-30R

SBP10KRMI4U 230V Smart-UPS RT

7.5-10kVA

HW (3Ph

or 1Ph)

HW (3Ph

or 1Ph)

HW (8) C13,

(2) C19

SBP16KP 200-240V

Symmetra LX

4-16kVA

HW (3Ph

or 1Ph)

HW (3Ph

or 1Ph)

HW HW

SBP16KRMI4U 220-240V

Symmetra LX

4-16kVA

HW (3Ph

or 1Ph)

HW (3Ph

or 1Ph)

HW (3) 30A HW

SBP16KRMP4U 200/208/240

Symmetra LX

4-16kVA

HW HW HW (6) L14-30R

SBP16KRMP4U-HW 200/208/240

Symmetra LX

4-16kVA

HW HW HW (1) L14-30R,

(3) L5-20R,

(1) 100A HW

*For loads exceeding 3kVA, hardwiring is necessary.

**For loads exceeding 5kVA, hardwiring is necessary.

Rea

Front

Produkt Specifikationer

Mærke:	APC
Kategori:	Ikke kategoriseret
Model:	SBP16KRMI4U
Vekselstrømsindgangsspænding:	230 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Bredde:	432 mm
Dybde:	673 mm
Højde:	178 mm
Vægt:	21820 g
Produktfarve:	Sort
Produkttype:	Bypass-afbryder
Pakkevægt:	31820 g
Pakkedybde:	991 mm
Pakkebredde:	610 mm
Pakkehøjde:	305 mm
Opbevaringstemperatur (T-T):	-40 - 65 °C
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 95 %
Driftstemperatur (T-T):	-20 - 45 °C
Dimensioner (BxDxH):	432 x 673 x 178 mm
Certificering:	CSA, EN 60950, GOST, IEC 60950, IEC 60950, UL 1778
Monteringstype:	Reolbeslag
Harmoniseret systemkode (HS):	85079080
Bæredygtighedscertifikater:	RoHS
Indgangsspænding:	230 V
Driftshøjde:	0 - 4500 m
Ikke-drift højde:	0 - 15000 m
Kompatible produkter:	CSA, EN 60950, GOST, IEC 60950, IEC 60950, UL 1778
Indgangsfrekvens:	50/60 Hz
Kapabilitet:	CSA, EN 60950, GOST, IEC 60950, IEC 60950, UL 1778
Total effekt:	Hard Wire 3-wire W
Load-kapacitet:	20000 VA
Maksimal strømtræk pr. fase:	100 A
Rackkapacitet:	4U
Udgangsspænding note:	(3) Hard Wire 3-wire (H N + G)
Strømstyring:	Ja
Antal faser:	1