APC Smart-UPS SRTL004 Manual


Læs gratis den danske manual til APC Smart-UPS SRTL004 (4 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 21 anmeldelser. Har du et spørgsmål om APC Smart-UPS SRTL004, eller vil du spørge andre brugere om produktet?

Side 1/4
Installation Guide APCSmart-UPS Ultra
Power Distribution Unit (PDU)
SRTL002/SRTL003/SRTL004/SRTL005
Important Safety Instructions
SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed during
installation and maintenance of the Smart-UPS and batteries.
Read the user documentation to become familiar with the equipment before trying to install or operate
it.
The following special messages may appear throughout this bulletin or on the equipment to warn of potential
hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of this symbol either to a “Danger” or “Warning safety label indicates that an electrical
hazard exists which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate
injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
APC Smart-UPS Ultra SRTL002/SRTL003/SRTL004/SRTL0052
Package Contents
Inspect the contents upon receipt. Notify the carrier and dealer if there is damage.
PDU Replacement
The PDU in the following illustration is only for representation. The procedure is applicable for all the PDUs,
SRTL002, SRTL003, SRTL004, and SRTL005.
Removal of the existing PDU
Hardwiring PDU (SRTL002) PDU with 2x L6-30 and 2x L6-20 receptacles
(SRTL005)
IEC PDU (SRTL003)
PDU with 4x L6-20 receptacles (SRTL004)
CAUTION
RISK OF DAMAGE TO EQUIPMENT OR PERSONNEL
PDU must replaced by a qualified electrician or a service personnel.
Adhere to all local and national electrical codes.
Failure to follow these instructions could result in equipment damage and minor or moderate injury.
Turn off the UPS Output (refer to the UPS Operation Manual for details) by selecting the Turn Off Immediately
option.
Turn off the input power to the UPS at the wall socket.
Loosen the thumbscrew and turn off the BATTERY /ON OFF switch, on the internal battery module in the UPS.
Disconnect XLBPs connected to the UPS, if any.
Unplug all the connected equipment from the output sockets of the UPS.
Locate the screws securing the standard PDU to the
UPS and unfasten them using a Torx® T20 driver bit.
Slide the PDU to the left to align the locking pin with
the keyhole.
4X


Produkt Specifikationer

Mærke: APC
Kategori: Uafbrydelig strømforsyning (UPS)
Model: Smart-UPS SRTL004

Har du brug for hjælp?

Hvis du har brug for hjælp til APC Smart-UPS SRTL004 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Uafbrydelig strømforsyning (UPS) APC Manualer

Uafbrydelig strømforsyning (UPS) Manualer

Nyeste Uafbrydelig strømforsyning (UPS) Manualer