APC Smart-UPS SUA24XLBP Manual

APC Uafbrydelig strømforsyning (UPS) Smart-UPS SUA24XLBP

Læs gratis den danske manual til APC Smart-UPS SUA24XLBP (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om APC Smart-UPS SUA24XLBP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Smart-UPS® External Battery Pack SUA24XLBP

990-5054 04/2011

Refer to the User Manual for basic information about the Smart-UPS and the Smart-UPS XL Supplement for additional information on extended run versions of the

UPS. This supplement provides information on the battery packs.

Installation

Inspection

Inspect the battery pack upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly.

Placement

This figure shows the location of the battery pack connector.

The battery pack connector is color coded and keyed to prevent improper connection. Do not attempt to

install battery packs with connectors that are a different color from the battery pack connector on the UPS.

Install up to 10 battery packs per XL model UPS following the instructions below.

1. Prepare the UPS to connect the battery pack(s).

Note the holes used to attach the battery pack

connector clamp (near the center of the

connector opening). Use a #2 Phillips head

screwdriver to remove the battery pack

connector clamp from the back of the UPS.

3. Holding the clamp aside, insert the battery pack connector into

the UPS.

2. Turn the clamp over and loosely attach one end

at the edge of the connector opening in the

UPS.

4. Secure the connector clamp.

For additional battery packs, repeat this procedure using the battery pack connectors on the battery packs.

Note: Do not stack battery packs. Stacking results in a tipping hazard.

Storage

Storage Conditions

Store the battery pack covered and upright in a cool, dry location, with its

batteries fully charged. Before storing, charge the battery pack for at least

4 hours.

Extended Storage

At -15 to +30 °C (+5 to +86 °F), charge the battery pack every 6 months

At +30 to +45 °C (+86 to +113 °F), charge the battery pack every 3 months.

Battery Charge and Run Times

A floppy disk is shipped with each battery pack to configure your Smart-UPS for use with each new battery pack added. Your Smart-UPS needs to be configured

appropriately so that it can better calculate the discharge time. Connect the UPS’ port to a serial port on a PC or workstation running DOS or Windows, by using the

black colored communications cable included. Next, while at the DOS prompt, insert the floppy disk into a drive and change to that drive’s letter (e.g.. A:) Then

type: battpack com[X] [Y], where [X] = 1 or 2 depending on the serial port used, and [Y] = number of battery packs attached to the UPS.

The Smart-UPS XL Supplement contains tables showing both the time required for charging UPS and battery pack batteries for rated protection and typical run

times.

Replacing the Battery

This battery pack has easy to replace hot-swappable batteries. Battery replacement is a safe procedure, isolated from electrical hazards. You may leave the UPS and

loads on for the following procedure. See your dealer or call the number in this manual for information on replacement battery kits.

Note: Please read the cautions in the APC Safety Guide. Save your data before beginning this procedure. Once the battery is disconnected, the loads are

not protected from power outages.

Battery Replacement Procedure - Rack Mount XL Battery Packs

1.Reach into the finger pull and remove the front cover.

2.Use a flat-blade, screwdriver or coin to remove the battery

door screws and open the door.

Warning! Do not force the battery out. This may

damage internal wiring!

3.Disconnect the battery connector by pulling on the white

cord on the side of the battery.

4.Slide the battery out of the battery pack.

5.Remove the foam separator.

6.Repeat steps 3 - 5 for the second battery.

7.Repeat steps 3 - 6 for the two batteries on the other side of

the battery pack.

Note: Be careful removing the batteries - they are heavy..

8.Slide the new battery into the battery pack.

9.Connect the battery connector

Note: Small sparks at the battery connectors are normal

during connection.

10.Push the battery in as far as it will go. There are stops in

the back to prevent it from going too far.

11.Replace the foam separator.

12.Repeat steps 8 - 10 for the second battery.

13.Repeat steps 8 - 12 for the two batteries on the other side

of the battery pack.

14.Close the battery door, replace the battery compartment

screws, and replace the front cover.

15.Dispose of the old battery properly at an appropriate

recycling facility or return it to the supplier in the packing

material for the new battery. See the new battery

instructions for more information.

Specifications

Typical Battery Life 3 to 6 years, depending on number of discharge

cycles and ambient temperature

Operating Temperature 0 to 40°C (+32 to +104°F)

Storage Temperature -15 to 45°C (+5 to _113°F)

Operating and Storage

Relative Humidity

0 to 95%, non-condensing

Operating Elevation 0 to +3,000 m (0 to +10,000 ft.)

Storage Elevation 0 to +15,000 m (0 to +50,000 ft.)

Size (H x W x D) Tower:

21.6 x 17.0 x 43.9 cm

(8.5 x 6.7 x 17.3 in.)

Rack Mount:

17.8 x 48.3 x 45.7 cm

(7.0 x 19.0 x 18.0 in.)

Weight - net (shipping) 31.3 (33.1) kg

69.0 (73.0) lb.

61.7 (69.4) kg

136.0 (153.0) lb.

PowerChute are owned by Schneider Electric Industries S.A.S., American

Power Conversion Corporation, or their affiliated companies. All other

trademarks are property of their respective owners.

Battery Replacement Procedure - Tower XL Battery Packs

1.Grasp the side of the front cover and tilt it out and down.

2.Unhook the bottom of the cover from the chassis and

remove it to expose the battery door

3.Use a flat-blade screwdriver or a coin to remove the two

battery door screws and open the door.

4.Pull the white cord on the front battery connector to remove

the battery connector.

5.Grasp the tab and gently pull the battery out of the battery

pack.

6.Reach into the battery compartment and grasp the white

cord on the other battery connector. Pull firmly to

disconnect the connector and remove the second set of

batteries.

Note: Be careful removing the batteries - they are heavy..

7.Slide the first set of new batteries into the unit. Hold the

connector down below the top of the batteries and toward the

door, otherwise the assembly will not fit. Guide the

connector over the top of the batteries and press firmly to

connect it to the rear connector of the battery compartment.

Note: Small sparks at the battery connectors are normal

during connection.

8. Slide the second set of batteries in, then guide the connector

over the batteries and press firmly to connect it to the front

connector of the battery compartment.

9.Now close the battery door, replace the screws, and replace

the front cover.

10.Dispose of the old battery properly at an appropriate

recycling facility or return it to the supplier in the packing

material for the new battery. See the new battery instructions

for more information.

APC Customer Support and Warranty

APC Web site: www.apc.com/jp

Telephone: 03-6402-2030

Limited Warranty

APC® by Schneider Electric warrants its products to be free from defects in materials

and workmanship for a period of six months from the date of purchase. Its obligation

under this warranty is limited to repairing or replacing, at its own sole

option, any such defective products. To obtain service under warranty you must obtain a

Returned Material Authorization (RMA) number from customer support. Products must

be returned with transportation charges prepaid and must be

accompanied by a brief description of the problem encountered and proof of date and

place of purchase. This warranty does not apply to equipment that has been damaged by

accident, negligence, or misapplication or has been altered or modified in any way. This

warranty applies only to the original purchaser who must have properly registered the

product within 10 days of purchase.

EXCEPT AS PROVIDED HEREIN, AMERICAN POWER CONVERSION MAKES

NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states

do not permit limitation or exclusion of implied warranties; therefore, the aforesaid

limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL APC BE LIABLE FOR

DIRECT, INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF

THIS PRODUCT, EVEN IF

ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, APC is not

liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of

equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or

otherwise.

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	Smart-UPS SUA24XLBP

Har du brug for hjælp?

Hvis du har brug for hjælp til APC Smart-UPS SUA24XLBP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Uafbrydelig strømforsyning (UPS) APC Manualer

APC E3MCBC10B Manual

6 August 2025

APC Back-UPS BE700G3 Manual

5 August 2025

APC GVSBPIT75 Manual

5 August 2025

APC GVLMBCA200K500H Manual

4 August 2025

APC E3SBPAR10K40F Manual

4 August 2025

APC BE650G2-GR Manual

4 August 2025

4 August 2025

4 August 2025

4 August 2025

4 August 2025

Uafbrydelig strømforsyning (UPS) Manualer

Nyeste Uafbrydelig strømforsyning (UPS) Manualer

ATen EC1000 Manual

28 September 2025

Riello SEP 1500 Manual

20 September 2025

Riello Dialog Vision Manual

20 September 2025

Panamax MB1000 Manual

4 September 2025

Panamax MB1500 Manual

4 September 2025

Akyga AK-ND-41 Manual

30 August 2025

CyberPower HSTP3T30KEBCWOB Manual

20 August 2025

Vorago UPS-400 Manual

20 August 2025

CyberPower RT33020KE Manual

20 August 2025

CyberPower Value2200EILCD Manual

20 August 2025