APC SRT192BP2US Manual

APC Ikke kategoriseret SRT192BP2US

Læs gratis den danske manual til APC SRT192BP2US (20 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 13 anmeldelser. Har du et spørgsmål om APC SRT192BP2US, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/20

Installation Guide Smart-UPS™ On-Line

External Battery Pack SRT192BP/

SRT192BP2/SRT192BPJ/SRT192BP2J

Safety Messages

SAVE THESE INSTRUCTIONS - This manual contains important instructions that should be followed during

installation and maintenance of the Smart-UPS and batteries.

Read these instructions carefully and look at the equipment to become familiar with the device before trying to install,

operate, service or maintain it. The following special messages may appear throughout this bulletin or on the equipment

to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

The addition of this symbol either to a “Danger” or “Warning” safety label indicates that an electrical

hazard exists which will result in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury or death.

Product Handling Guidelines

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate

injury.

NOTICE

NOTICE is used to address practices not related to physical injury.

<18 kg

<40 lb

18-32 kg

40-70 lb

32-55 kg

70-120 lb

>55 kg

>120 lb

Smart-UPS On-Line External Battery Pack SRT192BP/SRT192BP2/SRT192BPJ/SRT192BP2J2

Safety and General Information

• Adhere to all national and local electrical codes.

• Changes and modifications to this unit not expressly approved by APC by Schneider Electric could void

the warranty.

• This unit is intended only for indoor use in a controlled environment.

• Do not operate this unit in direct sunlight, in contact with fluids, or where there is excessive dust or humidity.

• Be sure the air vents on the unit are not blocked. Allow adequate space for proper ventilation.

• The UPS and external Battery Pack(s) must be properly grounded to each other and to the mains grounding

system.

• Before installing or replacing the batteries, remove jewelry such as wristwatches and rings.

High, short circuit current through conductive materials could cause severe burns.

• The battery typically lasts for two to five years. Environmental factors impact battery life. Elevated ambient

temperatures, poor quality mains power, and frequent short duration discharges will shorten battery life.

• Replace the battery immediately when the UPS indicates battery replacement is necessary or when the batteries

reach the end of their life. Failure to do so could result in equipment damage and/or injury.

• The UPS will recognize as many as 10 XLBPs connected to the UPS.

Note: For each XLBP added, increased recharge time will be required.

• The equipment is heavy. Always practice safe lifting techniques adequate for the weight of the equipment.

• The batteries are heavy. Remove the batteries before installing the UPS and external battery packs (XLBPs) in a

rack.

• Always install XLBPs at the bottom in rack-mount configurations. The UPS must be installed above the XLBPs.

• Do not dispose of batteries by burning them. The batteries may explode.

• Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes, and may be toxic.

• Always recycle used batteries.

• Recycle the package materials or save them for reuse.

• Additional safety information can be found in the Safety Guide supplied with this unit.

Overview

• To verify that installation of an external battery pack (XLBP) has been successful, go to the UPS display

interface.

Perform an Alarm Test to determine if the XLBP is recognized by the UPS.

The LED on the XLBP will flash if successful communication has been established.

• When viewing the status of an XLBP on the UPS display interface screen, the LED on the corresponding XLBP

will flash.

• When an RBC needs to be replaced, perform a Runtime Calibration Test to verify that battery replacement is

required.

Produkt Specifikationer

Mærke:	APC
Kategori:	Ikke kategoriseret
Model:	SRT192BP2US
Bredde:	130 mm
Dybde:	683 mm
Højde:	432 mm
Vægt:	90810 g
Brugervejledning:	Ja
Produktfarve:	Sort
Batterispænding:	192 V
Pakkevægt:	101290 g
Pakkedybde:	1000 mm
Pakkebredde:	600 mm
Pakkehøjde:	420 mm
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Tower
Opbevaringstemperatur (T-T):	-15 - 45 °C
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 95 %
Driftstemperatur (T-T):	0 - 40 °C
Antal:	1
Bæredygtighedscertifikater:	RoHS
Driftshøjde:	0 - 3000 m
Ikke-drift højde:	0 - 15000 m