APC SurgeArrest Essential P6GC Manual

APC Ikke kategoriseret SurgeArrest Essential P6GC

Læs gratis den danske manual til APC SurgeArrest Essential P6GC (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 19 anmeldelser. Har du et spørgsmål om APC SurgeArrest Essential P6GC, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
07/2009990-3645
User Guide - Essential SurgeArrest®
Surge Protector with LCD Timer P4GC/P6GC
Complete and return the warranty card.
Read the safety instructions before installing the unit. Failure to follow these instructions may cause damage to
equipment.
• The SurgeArrest is intended for indoor use only. The internal components are not sealed from the environment.
• Do not install the SurgeArrest where there is excessive heat or humidity.
• Do not use extension cords with the SurgeArrest.
• Plug the SurgeArrest into a three wire, grounded receptacle only. If the Building Wiring Fault LED illuminates indicating a wiring
fault, discontinue use and have a qualified electrician check the building wiring for an overloaded neutral, reversed polarity, or a
missing ground.
• Never install electrical wiring during a lightening storm.
Overview and Operation
This unit enables the user to specify the time that all outlets controlled by the timer (for outlets on the P4GC and 5 outlets on the P6GC),
will turn on and off. Specific times of day and specific days of the week can be selected. See “LCD Timer” on page 2.
When unplugged from the wall outlet the unit will shut off in 20 seconds. Programmed settings will be held in memory for future use.
LCD Timer Display-The LCD timer display shows the settings selected using the the buttons described in this guide.
R (reset)-Push this button to clear all settings and reset the unit to the factory default state.
ON/OFF switch P6GC models only-This switch provides on/off power control to all of the outlets. To disconnect power to the
outlets on P4GC models, unplug the unit from the wall outlet. See “LCD Timer” on page 2.
TIME/OVERRIDE button-Use Time to set and display the current day and time. Use OVERRIDE as an on/off button for the
current program. OVERRIDE acts as a circuit breaker in output overload conditions. See “LCD Timer” on page 2.
CONTROLLED by TIMER outlets-P6GC models, five outlets are controlled by the timer. P4GC models, all four outlets are
controlled by the timer.
PROTECTION WORKING LED-This LED illuminates during normal operation of the CONTROLLED by MASTER outlets.
The LED will extinguish if a sustained high-energy power surge as with a lightening strike, causes the circuit breaker to trip. Disconnect
all equipment from the SurgeArrest before pushing the circuit breaker Reset button. If the LED does not illuminate after the circuit
breaker is reset and the Auto/Manual switch is switched to Auto, contact APC using the contact information provided in this guide.
BUILDING WIRING FAULT LED-This LED illuminates when there is no ground circuit, or there is a reversed polarity in the
building wiring. Discontinue use and have a qualified electrician check the wiring in the building
TIMER ENABLED-This LED illuminates when the LCD TIMER function is enabled. See “LCD Timer” on page 2.
P4GC P6GC
• •
PROTECTIO N WORKING
BUILDING
WIRING FAULT
TIMER ENABLED
srg006a
CONTROLLED BY MASTER
PROTECTIO N
WORKING
BUILDING
WIRING FAULT
TIMER ENABLED
990-36452
LCD Timer
The LCD timer enables the user to program the time that each of the outlets will turn on and off.
The numbered callouts in this section refer to the diagrams on page 1.
TIME/OVERRIDE button:
• TIME TIME button-Press the button to see the current time and day of the week. To change the time, press and hold the TIME
button while pressing the H+ (hours) and M+ (minutes) buttons. Release the TIME button when the correct time appears on the
display. To change the day, press and hold the TIME button while pressing the DAY button when the correct day appears on the
display.
• OVERRIDE OVERRIDE button- mode has two functions.
–OVERRIDE acts as an on/off switch for the current program settings. The unit will automatically go to the next program
settings.
– When an output overload condition occurs an internal circuit breaker will trip. The TIME/OVERRIDE switch will
automatically go to OVERLOAD mode. Correct the overload condition, then toggle the switch to the TIME position.
TIMER mode allows the user to program the time that all four outlets (as a group), will turn on and off. There are settings for six
potential programs.
Use the H+ (hours) and M+ (minutes) buttons to set the time for a program to turn on.
• Press the TIMER button once to display the On settings for program 1. Press the H+ and M+ buttons to set the time of day and the
day of the week. Release the TIME button when the correct time appears on the display. Refer to number 10 below for Day button
functionality.
• Press the TIMER button again to display the Off settings for program 1. Repeat the steps above to set the time of day and day of
the week program.
• Press the TIMER button again to display the On settings for program 2.
• Press the TIMER button again to display the Off settings for program 2.
• Continue this sequence of steps to configure up to six on/off programs.
The DAY button allows the user to select the days of operation for Timer mode. The possible selections for day or combinations of
days are listed below. Hold the button down to fast forward through the list.
• MO TU WE TH FR SA SU-The On/Off settings will repeat every day.
• MO-The On/Off settings will repeat every Monday.
• TU-The On/Off settings will repeat every Tuesday.
• WE-The On/Off settings will repeat every Wednesday.
• TH-The On/Off settings will repeat every Thursday.
• FR-The On/Off settings will repeat every Friday.
• SA-The On/Off settings will repeat every Saturday.
• SU-The On/Off settings will repeat every Sunday.
• MO TU WE TH FR-The On/Off settings will repeat every Monday through Friday.
• SA SU-The On/Off settings will repeat every Saturday and Sunday.
• MO TU WE TH FR SA-The On/Off settings will repeat every Monday through Saturday.
H+-sets the hours for operation. Hold the button down to fast forward through the number of hours.
M+-sets the minutes for operation. Hold the button down to fast forward through the number of minutes.
NOTE: To turn off the LCD display illumination, press and hold the DAY button for two seconds.The set functions will continue to
operate when the display is not illuminated. Press any of the buttons to turn the LCD display illumination back on.

Produkt Specifikationer

Mærke: APC
Kategori: Ikke kategoriseret
Model: SurgeArrest Essential P6GC

Har du brug for hjælp?

Hvis du har brug for hjælp til APC SurgeArrest Essential P6GC stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret APC Manualer

APC

APC AR7752W Manual

30 August 2025
APC

APC E3SXR7 Manual

5 August 2025
APC

APC E3MCBC7D Manual

4 August 2025
APC

APC Galaxy VS GVSOPT004 Manual

4 August 2025
APC

APC PME5B-GR Manual

4 August 2025
APC

APC SRT192RMBPM Manual

15 Juli 2025
APC

APC EPDU1216B Manual

15 Juli 2025
APC

APC APV9602 Manual

15 Juli 2025
APC

APC AP7922B Manual

15 Juli 2025
APC

APC InRow RC ACRC500 Manual

7 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kimo

Kimo LR 110 Manual

2 September 2025
HMS Premium

HMS Premium LPD02 Manual

2 September 2025
AVer

AVer E1008 Manual

2 September 2025
Biltema

Biltema 17-547 Manual

2 September 2025
Groen

Groen AH/1E Manual

2 September 2025
ACOPower

ACOPower HY-P30 Manual

2 September 2025
Yamaha

Yamaha True X Speaker 3A WS-X3A Manual

2 September 2025
Globe

Globe RG30 Manual

2 September 2025
Deye

Deye SUN-6K-SG05LP1-EU-AM2-P Manual

2 September 2025
Neutrik

Neutrik NLT4FXX Manual

2 September 2025