APC SYA8K8RMP Manual

APC Uafbrydelig strømforsyning (UPS) SYA8K8RMP

Læs gratis den danske manual til APC SYA8K8RMP (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 16 anmeldelser. Har du et spørgsmål om APC SYA8K8RMP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Symmetra LX

Rack-mount UPS

Symmetra LX

Tower UPS

990-1539B-001, 04/2006

Important Safety and Installation Instructions

This manual provides instructions on the wiring and connections for the

Symmetra LX tower and rack-mount UPS.

All electrical power and power control wiring must be installed by a qualified

electrician and comply with local and national regulations.

See and retain the product documentation shipped with your system for

other important installation, operation, and maintenance instructions.

Illustrations are representative. Your Symmetra LX configuration, including

components and optional APC equipment, may be different from the models

shown in this guide.

prohibited.

Symmetra LX

Electrical Installation Guide

Tower and Rack-mount UPS

For use with Symmetra LX UPS Models:

APC, the APC logo, PowerChute, InfraStruXure, Smart-UPS and Symmetra

are registered trademarks of American Power Conversion Corporation. All

other trademarks are the property of their respective owners.

200 V, 4 8 kV A

208/240 V, 4 8 kV A

200 V, 4 16 kV A

208/240 V, 4-16 kVA

Remove screws and slide out the hardwire assembly .

Attach an input conduit and if required, an output conduit .

Larger holes can be punched if necessary.

Detach the strain relief panel using nuts for easier access.

Complete Pre-installation Checklist

Check that the circuit breaker to be used to power the UPS is in the

OFF position.

Check that the input circuit breaker on the UPS is in the OFF

position.

Before beginning the electrical installation, perform the following procedures.

Read, understand and follow ALL safety instructions contained in

the

Failure to follow safety instructions and warnings could

result in equipment damage, serious injury, or death.

Symmetra LX Safety Instructions and General Information

Guide.

Electrical

Hazard

Refer to local and national codes. Many locations require hardwiring

by a licensed electrician.

Strain relief is required for all hardwiring.

All openings in the hardwire assembly must be covered. Failure to

do so may result in personal injury or equipment damage.

Hardwire the UPS

1.1

1.2

Caution

2.1

2.2

Electrical Installation

Maximum

Load

Maximum

Load

8 kVA

Circuit

Breaker

Rating*

Circuit

Breaker

Rating*

50 A

Connection

40 in-lb

4.5 -m)

4-Wire ( )

External circuit breaker

#3 AWG (22 mm JAPAN)

Torque to

( N

L1-L2-N-G

40 in lb

4.5 -m)

4-Wire (L1-L2-N-G)

External circuit breaker

#6 AWG (14 mm JAPAN)

Torque to -

( N

Voltage

(Vac)

Voltage

(Vac)

16 kVA 100 A

200, 208,

or 240

200, 208,

or 240

8 kVA 50 A §

§ 40 in lb

External circuit breaker

#6 AWG (14 mm JAPAN)

Torque to -

(4.5 N-

4-Wire (L1-L2-N-G)

2 (L14-30R)

4 (L5-20R)

16 kVA 90 A

100/200,

120/208,

or 120/240

100/200,

120/208,

or 120/240

40 in lb

External circuit breaker

#3 AWG (22 mm JAPAN)

Torque to -

(4.5 N-

4-Wire

(L1-L2-N-G)

4 (L14-30R)

8 (L5-20R)

Input Connections

Method

Hardwired

(Standard on

tower and

rack-mount)

Hardwired

(Standard on

tower and

rack-mount)

Hardwired

(Standard on

tower and

rack-mount)

Hardwired

(Standard on

tower and

rack-mount)

Output

receptacles

(Standard on

rack-mount)

Output

receptacles

(Standard on

rack-mount)

100/200,

120/208,

or 120/240

100/200,

120/208,

or 120/240

Output Connections

*Recommended

OUTPUT

INPUT

L1NL2L1

885-1821/1

Vdc

Attach an input cable and an output cable (if required) , to

the terminal block .

Pull the wires through the conduit into the hardwire assembly.

40 in lb

Reinstall the hardwire assembly with provided screws .

Test the wiring.

Turn on the utility power, the input circuit breaker , and the

system enable switch . If the Vin value on the display does

not match your branch voltage, check the input wiring.

Check the output wiring by turning on the maintenance bypass

switch .

Connect to the terminal block as indicated on the label ,

using a torque of - (4.5 N-m).

Cover the unused holes in the strain relief panel.

Inspect cable connections to ensure proper installation.

Reattach the strain relief panel with nuts .

Turn OFF the input circuit breaker and maintenance bypass

switch.

If your configuration includes an additional management accessory

card, install in the empty slot on the rear of the UPS. See the

accompanying documentation for installation instructions.

Loads can be connected directly to the UPS using the output

receptacles on the PDU panel. Ensure that the total load being

plugged into a PDU panel DOES NOT EXCEED the branch circuit

breaker rating on the PDU panel.

Install PDU Panel(s) and Connect Loads to the UPS,

If Applicable

Your configuration may include optional PDU panels. Refer to the PDU

installation guide.

Note

Remove the access panel to connect the circuits .

If your installation will use an external switch contact, connect

the REPO switch with the pre-installed jumper , as shown.

If your installation will use a switch contact and a 24 V power supply

external to the UPS, remove the jumper and connect the REPO

switch, as shown.

In many locations, the Remote Emergency Power Off

(REPO) switch must be installed by a licensed electrician.

Refer to local and national codes.

See the

for REPO requirements and detailed safety instructions.

Safety and General Information GuideSymmetra LX

Note

Connect Remote Emergency Power Off (REPO)

Circuit, If Required

Hardwire the UPS (continued)

Install Accessory Card, If Applicable

3.1

3.2

3.3

2.3

2.4

2.5

2.6

2.7

2.8

OU T PUT

INPUT

L1NL2L1

885-1821/1

Produkt Specifikationer

Mærke:	APC
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	SYA8K8RMP
Vægt:	178180 g
Batteriteknologi:	Blybatterier (VRLA)
Opbevaringstemperatur (T-T):	-15 - 45 °C
Driftstemperatur (T-T):	0 - 40 °C
Dimensioner (BxDxH):	472 x 688 x 572 mm
Støjniveau:	62 dB
Udgangseffekt:	6400 W
Certificering:	CSA,FCC Part 15 Class A,UL 1778
Opladningstid for batteri:	3 t
Grænseflade:	DB-9 RS-232, Smart-Slot
Indgangsfrekvens:	50/60 Hz
Lydalarmer:	Ja
Nominel indgangsspænding:	208 V
Output-forbindere:	1x 4-wire\n2x NEMA L14-30R\n4x NEMA L5-20R
Output strømkapacitet (VA):	8 kVA
Typisk backup tid ved halv styrke:	17 min.
Typisk backup tid ved fuld styrke:	5.9 min.
Nødstrøm Off (EPO):	Ja
Udgangsspænding note:	Configurable for 120/208 or 120/240 output voltage