Aputure MC 12-Light Production Kit Manual

Aputure Ikke kategoriseret MC 12-Light Production Kit

Læs gratis den danske manual til Aputure MC 12-Light Production Kit (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Aputure MC 12-Light Production Kit, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

-2- -3-

-9- -10--8-

-1-

Thank You!

Instructions

Detailed product manual for MC 12-Light Production Kit can be found on www.aputure.com.

Product Manual

English

Thank you for purchasing the Aputure MC 12-Light Production Kit. This kit

was designed for owner-operators and rental houses. Including 12

RGBWW Mini LEDs, a wireless charging hard case, four sets of accessories,

and both AC and D-Tap charging, the MC 12-Light Production kit has

everything needed to tackle any lighting challenge.

Please read this product manual carefully.

Keep this product manual and always include it when passing the

product onto third parties.

Do not place the product near any corrosive WARNING:

chemicals. Corrosion may cause the product to malfunction.

Only use a microﬁber or dry cloth to clean the product.

Be careful to not damage the light by dropping it or otherwise

introducing physical shock.

Do not leave the product in excessive heat, high temperatures can cause

the product to malfunction.

Please have the product checked by the authorized service or agent if

your product has some problems. Please note that this warranty does

not apply to repair arising out of the malfunction of unauthorized

disassembly, although you may request such repairs on a chargeable

basis.

Use of original Aputure cable accessories is recommended. Please note

that this warranty does not apply to repairs arising out of the

malfunction of non-original Aputure accessories, although you may

request such repairs on a chargeable basis.

The product is certiﬁcated by RoHS, CE, KCC and Japan MIC etc. Please

operate the product in full compliance with the operation standards.

Please note that this warranty does not apply to repair arising from

malfunction, although you may request such repairs on a chargeable

basis.

The instructions and information in this manual are based on thorough,

controlled company testing procedures. Further notice will not be given

if the design and speciﬁcations change.

8. Attaching the Silicone Diﬀuser

9. Using the Mounting Tape

10. Using the Magnets

Components List

Adhesive Mounting

Tape (8 pairs)

Silicone Rubber

Diﬀuser (4 pcs)

MC (12 pcs)

MC 12-Light Wireless

Charging Case (1 pc)

USB Type-C Charging

Cable

(2 pcs)

Power Cable

(1 pc)

D-Tap to D-Tap

Power Cable

(1 pc)

Package includes the following items:

Product Details

-6- -7-

-4-

3. MC Power ON/OFF

Adjust the position of the power switch to turn the light on or oﬀ.

Don’t attach this device or the magnets to any surface with a temperature

above 80°C. Doing otherwise can damage the magnets.

OLED Screen

2 Function Control Wheel

Power Switch

USB Type-C Charging Port

Magnets

1/4"-20 Screw Mount

Drawer Latches

Accessory Drawer

Wireless Charging Pads

Status Leds

Power Switch

AC Power Input

DC D-Tap Input

Rubber D-Tap Cover

USB Type-A Outputs

1 2 3 4

7. MC Bluetooth Mode

Press and hold the control wheel for 2 seconds to access the system

menu. Rotate the control wheel to select BT and press the wheel to the

Bluetooth Reset menu. Rotate the control wheel to select "YES" and short

press the wheel to reset the device's Bluetooth pairing, (the pop-up

window displays the current reset progress. The reset process completes

within 5 seconds.) or select "NO" to return to the system menu.

11. Using the Sidus Link APP

4. MC CCT Mode

5. MC HSI Mode

6. MC FX Mode

Press and hold the control wheel for 2 seconds to access the system menu.

Rotate the control wheel to select CCT and press the wheel to enter CCT

mode. In CCT Mode, rotate the control wheel to adjust the color

temperature between 3200-6500K. "Short press" the wheel to select

intensity (INT) control, and turn the wheel to adjust the brightness level

from 0-100%.

* Access more ﬁne control via the Sidus Link mobile application.

Press and hold the control wheel for 2 seconds to access the system menu.

Rotate the control wheel to select HSI and press the wheel to enter HSI

mode. In HSI Mode, "short press" the control wheel to toggle between

HUE/SAT (saturation)/INT (intensity) controls. When controlling HUE,

rotate the control wheel to adjust the hue color from 0-360°. When

controlling saturation (SAT), turn the control wheel to adjust the color

saturation between 0-100%. When controlling intensity (INT), turn the

wheel to adjust the brightness level between 0-100%.

Press and hold the control wheel for 2 seconds to access the system menu.

Rotate the control wheel to select FX and press the wheel to enter FX

mode. In FX mode, rotate the control wheel to toggle between diﬀerent

lighting FX presets: Paparazzi, Fireworks, Faulty Bulb, TV, Lightning, Party,

Pulsing, Cop car, & Fire. Once you have selected your desired lighting

eﬀect, "short press" the control wheel to access intensity (INT) control.

Rotate the control wheel to adjust the brightness of the lighting eﬀect

from 0-100%.

(1) Paparazzi (2) Fireworks

(3) Faulty Bulb (4) TV

(5) Lightning (6) Party

(7) Pulsing

(9) Fire

(8) Cop Car

-5-

Operation Instructions

1. Powering the MC 12-Light Charging Case

2. Charging

1). Wireless charging

2). DC Power

1). AC Power

* The status LED will ﬂash red to indicate that there is a foreign metal object on

the wireless charging pad. Please remove immediately.

WARNING: Do not close the lid when the charging case on or in an active

charging state, to prevent overheating. Failure to do so will result in the internal

temperature of the case and the MCs being charged to become extremely hot.

* We advise charging the MC after ﬁrst powering oﬀ the light for optimal charging

speed. Attempting to charge the device while it is powered on will decrease its

charging speed.

The Aputure MC is compatible with the Qi wireless charging protocol. FIrst

ensure that the charging case is plugged into a compatible power source, then

ﬂip the power switch to the ON position. MCs can then be wirelessly charged by

placing them on each wireless charging pad. If an MC is detected and is

charging, the charging pad's corresponding status LED will appear red. If the

MC's battery is full, the status LED will appear green.

When powering the MC 12-Light Charging Case with a D-Tap Battery, ﬁrst

ensure that your battery is capable of delivering enough wattage to power the

charging case. With all wireless charging pads and USB ports active, the

charging case and draw up to 150W.

Metal Surface

Aputure Imaging Industries Co., Ltd.

Add: F/3, Building 21, Longjun industrial estate,

HePing West Road, Shenzhen, Guangdong

E-MAIL: cs@aputure.com

Sales Contact: (86)0755-83285569-613

Aputure Imaging Industries Co., Ltd. warrants the original consumer purchaser

from defects in material and workmanship for a period of one (1) year after the

date of purchase. For more details of warranty visit www.aputure.com

Serial No.

Item Name

Purchase Date

Buyer Name

Buyer Phone

Buyer Add

Franchiser Seal

Add F/3, Building 21, Longjun Industrial Estate, Heping West Road, Shenzhen, Guangdong:

Aputure Imaging Industries Co.,Ltd.

Inspection: Qualified

Intended Use

Intended use of the MC 12-Light Production Kit includes:

The user has read the instructions of this manual.

The user is using the products within the operating conditions and

limitations described in this product manual.

“Improper use” means using the products other than as described in

these instructions or under operating conditions which diﬀer from those

described herein.

MC 12-Light Production Kit

Coldshoe Ball head

(4 pcs)

+3/8” to 1/4” screw nut

(4 pcs)

2). Type-C charging

* The MC supports quick charging via USB-C PD protocol.

Charging is slow when the light is powered on. Turn the light oﬀ for optimal charging.

* The MC on-screen battery indicator will ﬂash when the battery level is too low.

As the light is charging, the on-screen battery level indicator will animate

to show the battery's status. After the battery is fully charged, the battery

level indicator will be displayed as full.

* The MC supports 5V/2A charging via power brick or power bank.

Specifications

* These are average results , the speciﬁc lux values may vary slightly between each

lighting ﬁxture.

Color Temperature 3200-6500K

CRI 96+

TLCI 97+

Illuminance Distance

Maximum Brightness

Battery Type Lithium-polymer Battery

(3.7V 2600mAh)

Rated Output Power

Operating Temperature

0 OC to 45 OC

Operating Battery Life >2hrs

Max Brightness Min Brightness

>15hrs

0.5M 1M0.3M

1100 lux 400 lux 100 lux

Battery Recharge Time

~1.5 hours via USB PD

~2 hours via USB DC 5V 2A/

~3.5 hours via wireless charging

Dimension 93x61x17mm/3.66x2.40x0.67in

AC Power Supply

Operating Current

Power Consumption

Battery Requirement

Max Power Output

Max Wireless Charging Power Output

AC 100V~240V 50/60Hz

<2A

180W maximum

DC 12V~16.8V ≥15A

150W

12x10W

Dimension 436.7x383.8x134.9mm/17.19x15.11x5.31in

MC 12-Light Wireless Charging Case

You can download the Sidus Link app from the iOS App Store or Google

Play Store for enhancing the functionality of the light. Please visit

sidus.link/app/help for more details regarding how to use the app to

control your Aputure lights.

Sidus.link/app/help

AC 100V-240V

Produkt Specifikationer

Mærke:	Aputure
Kategori:	Ikke kategoriseret
Model:	MC 12-Light Production Kit
Vekselstrømsindgangsspænding:	100 - 240 V
Bredde:	383.8 mm
Dybde:	134.9 mm
Vægt:	9200 g
Produktfarve:	Sort
Antal:	1
Batterier inkluderet:	Ja
Lampetype:	LED
Strømkilde type:	AC, Battery, DC
Bæretaske:	Ja
Lysfarve:	Variabel
Genopladeligt batteri:	Ja
Pære levetid:	- t
Farvetemperatur (maks.):	6500 K
Dæmpbar:	Ja
Antal lyskilder:	12 pære(r )
Total effekt:	- W
Belysningsstyrke:	1100 Lux
Højde (maks.):	436.7 mm
Farvetemperatur (min.):	3200 K
Justerbar farvetemperatur:	Ja
Energiforbrug pr. 1000 timer:	- kWh