NUVO 60/204 Manual

NUVO Lys 60/204

Læs gratis den danske manual til NUVO 60/204 (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 2 anmeldelser. Har du et spørgsmål om NUVO 60/204, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES

YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE

IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this fixture. Be sure to

follow the steps in the order given. Under no circumstances

should a fixture be hung on house electrical wires, nor should a

swag type fixture be installed on a ceiling, which contains a

radiant type heating system. Read instructions carefully. If you

are unclear as to how to proceed, consult a qualified electrician.

NOTE: Proper wiring is essential for the safe operation of this

fixture

FIXTURE ASSEMBLY

Carefully remove the fixture from the carton and check that all

parts are included as shown in figure. Be careful not to misplace

any of the screws or parts, which are needed to install this

fixture.

INSTALLATION

IMPORTANT: Do not attach fixture directly to outlet box.

STEP 1: Secure the mounting bar (A) to outlet box with the

outlet box screws (B). Thread the nut (D) onto the

nipple (E) so that five threads are exposed above the

nut (D). Insert the lock washer (C) and thread the

nipple (E) into the mounting bar (A), then secure with

the nut (D).

STEP 2: Thread the screw collar (H) onto the nipple (E). Slide

the screw collar ring (G) and the canopy (F) over the

chain (I). Using two pairs of pliers, open one link on

the end of the chain (I) and attach it to the screw collar

(H), repeat this step for the loop (J).

BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.

STEP 3: Lace wires up through chain (I) and pass wires through

holes in screw collar (H). We recommend lacing wire

up through every other link of chain (I).

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two

raised dimples on the mounting bar. Wrap the ground

wire from the fixture (if supplied) around the green

grounding screw, then connect it to ground wire from

the outlet box (if not fixed on the outlet box) using a

wire connector (not supplied). If ground wire from the

fixture is not supplied, wrap the ground wire (if not

fixed on the outlet box) from the outlet box around the

green grounding screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your fixture.

Identify which group your fixture wire(s) falls into and

connect the wires according to the directions below:

GROUP A: Connect to Black

House Wire

GROUP B: Connect to White

House Wire

BLACK WHITE

*PARALLEL WIRE (round &

smooth)

*PARALLEL WIRE (square &

ridged)

WHITE OR GREY WITH

TRACER

WHITE OR GREY WITHOUT

TRACER

BROWN GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

*NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer

wire is square shaped or ridged and the less tracer wire is round

in shape or smooth (seen best when viewed from wire end.)

STEP 3: Take your fixture wire(s) from group A and place

evenly against the black wire from the outlet box. Do

NOT twist wires together before using wire connectors.

STEP 4: Fit a wire connector over the wires and screw the

connector clockwise until you feel firmness.

STEP 5: Try gently to pull the connector off the wires. If you can

pull the connector off, carefully re-do steps 3 and 4 as

above, and check again for a firm connection.

STEP 6: Connect the fixture wire from group B to the white wire

from the outlet box in the same manner. Make sure no

bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside

outlet box, then secure the canopy (F) with the screw

collar ring (G).

STEP 2: Install lamps. (Please do not exceed the maximum

capacity recommended on the socket.)

STEP 3: Slide the washer (R) onto the nipple (Q), then allow the

nipple (Q) to protrude through the glass (S) and thread

the finial (T) onto the nipple (Q). Insert the lock locker

(P) and secure the glass (S) with the nut (O).

STEP 4: Place the glass (S) over the plate (U), Raise the plate

(U) and connect the hooks (L) of the arms (M) to the

loops (K), connect the hooks (N) of the arms (M) to the

loops (V).

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild

soap. Do not use abrasive materials such as scouring pads or

powders, steel wool or abrasive paper.

Line art shown may not exactly match the fixture enclosed.

However, the installations do apply to this fixture.

ITEM: 60-204 60-212 60-224 60-228 60-244

60-1263

NUV

Satco Product

LIGHTING

Produkt Specifikationer

Mærke:	NUVO
Kategori:	Lys
Model:	60/204

Har du brug for hjælp?

Hvis du har brug for hjælp til NUVO 60/204 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys NUVO Manualer

11 December 2025

11 December 2025

11 December 2025

11 December 2025

11 December 2025

11 December 2025

10 December 2025

10 December 2025

10 December 2025

10 December 2025

Lys Manualer

Nyeste Lys Manualer

Lightcraft Sandshine Manual

11 December 2025

Craftmade Cadence 54661 Manual

11 December 2025

Robert Abbey A697X Manual

11 December 2025

Lightcraft Solarlux Manual

11 December 2025

Quoizel CSE1910EK Manual

11 December 2025

Dainolite DM2578-F Manual

11 December 2025

AFX RAMV3603L30D1SN Manual

11 December 2025

Dals CFLEDSQ14-CC Manual

11 December 2025

Dals MSL10G Manual

11 December 2025

Dals CFLEDSQ10-CC Manual

11 December 2025