Asrock N68-GS4 FX R2.0 Manual

Asrock Bundkort N68-GS4 FX R2.0

Læs gratis den danske manual til Asrock N68-GS4 FX R2.0 (26 sider) i kategorien Bundkort. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Asrock N68-GS4 FX R2.0, eller vil du spørge andre brugere om produktet?

Side 1/26
1
NVIDIA RAID Installation Guide
1. NVIDIA BIOS RAID Installation Guide …………………….. 2
1.1 Introduction to RAID …………………………………. 2
1.2 RAID Configurations Precautions ……………….. 3
1.3 Installing Windows / 64-bit / Vista / 8 / 8 64-bit / 7 7
Vista 64-bit / XP / XP 64-bit With RAID Functions ….. 5
1.3.1 Installing Windows XP / XP 64-bit With
RAID Functions ……………………................. 5
1.3.2 Installing Windows 8 / 8 64-bit / 7 / 7 64-bit
/ Vista / Vista 64-bit With RAID Functions ...... 7
1.4 Create Disk Array ……………………………………….. 8
2. NVIDIA Windows RAID Installation Guide ………………… 11
2.1 NVIDIA Windows RAID Installation Guide for Windows
XP / XP 64-bit Users …………………… ……. 11 ...........
2.2 NVIDIA Windows RAID Installation Guide for Windows
8 / 8 64-bit / 7 / 7 64-bit / Vista / Vista 64-bit Users ….. 21
2
1. NVIDIA BIOS RAID Installation Guide
NVIDIA BIOS RAID Installation Guide is an instruction for you to configure RAID
functions by using NVIDIA RAID Utility under BIOS environment. After you make a
SATA / SATAII driver diskette, press <F2> to enter BIOS setup to set the option to
RAID mode by following the detailed instruction of the “User Manual” in our support CD
or “Quick Installation Guide”, you can start to use NVIDIA RAID Utility to configure
RAID.
This section includes examples of using NVRAID RAID Utility for creating RAID arrays.
If your motherboard is equipped with two SATA / SATAII ports, you may choose to use
RAID 0, RAID 1, or JBOD function with your motherboard. If your motherboard is
equipped with four SATA / SATAII ports, you may choose to use RAID 0, RAID 1,
RAID 0+1, JBOD, or RAID 5 function with your motherboard according to the SATA /
SATAII HDDs amount you install. Please refer to the RAID functions your motherboard
provides in advance and follow the instruction in this section to create RAID arrays.
1.1 Introduction to RAID
The term “RAID” stands for “Redundant Array of Independent Disks”, which is a
method combining two or more hard disk drives into one logical unit. For optimal
performance, please install identical drives of the same model and capacity when
creating a RAID set.
RAID 0 (Data Striping)
RAID 0 is called data striping that optimizes two identical hard disk drives to read and
write data in parallel, interleaved stacks. It will improve data access and storage since
it will double the data transfer rate of a single disk alone while the two hard disks
perform the same work as a single drive but at a sustained data transfer rate.
WARNING!!
Although RAID 0 function can improve the access performance, it does not provide any fault
tolerance. Hot-Plug any HDDs of the RAID 0 Disk will cause data damage or data loss.
RAID 1 (Data Mirroring)
RAID 1 is called data mirroring that copies and maintains an identical image of data
from one drive to a second drive. It provides data protection and increases fault
tolerance to the entire system since the disk array management software will direct
all applications to the surviving drive as it contains a complete copy of the data in
the other drive if one drive fails.


Produkt Specifikationer

Mærke: Asrock
Kategori: Bundkort
Model: N68-GS4 FX R2.0

Har du brug for hjælp?

Hvis du har brug for hjælp til Asrock N68-GS4 FX R2.0 stil et spørgsmål nedenfor, og andre brugere vil svare dig