Audibax CS6T Manual

Audibax Højttaler CS6T

Læs gratis den danske manual til Audibax CS6T (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Audibax CS6T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

CS CS CS5T / 6T / 8T

Please read the manual before using the product

USER´S

MANUAL

CS CS CS5T / 6T / 8T

Note: Anytime you note distortion, reduce the volume to a lower setting. Never allow

your amplifier to be driven into “clipping”. Otherwise the speakers may be damaged.

Damage caused by operating the speakers at distorted volume levels is not covered

by the warranty.

CARE AND MAINTENANCE

·Turn off the power to the speaker when unused for long periods of time.

·Ensure all equipment is turned off prior to cleaning. Surfaces need only occasional

dusting/cleaning. Never use chemicals or solvents as they may damage the surface.

Always clean using a dry cloth.

·Never touch the speaker drivers.

SPECIFICATIONS

Model

CS5T

CS6T

CS8T

Woofer

5.25" Woven Glass Fiber

Cone

6.5" Woven Glass Fiber

Cone

8" Woven Glass Fiber

Cone

Tweeter

0.75" Titanium Dome

Frequency Response

70Hz-20kHz

60Hz-20kHz

50Hz-20kHz

Sensitivity(1M/1W)

90dB

Nominal Impedance

8Ω

RMS Power

40W

60W

80W

Transformer

C100V: 3.75W-7.5W-15W

C100V: 7.5W-15W-30W

C100V: 10W-20W-40W

Dimensions

Ø204x78mm(Ø8"x3.1")

Ø234x87mm(Ø9.2"x3.4")

Ø284x110mm(Ø11.2"x4.3")

Cutout Size

Ø179mm(Ø7")

Ø210mm(Ø8.3")

Ø258mm(Ø10.2")

100

Amplifier

CS CS CS5T / 6T / 8T USER´S

MANUAL

1 2

SAFETY INSTRUCTIONS

·Please read the instructions carefully before installation and use. Keep the manual

safe for future reference.

·Prior to installing the speakers into any ceiling/wall, check the structure for weight

bearing ability and avoid contact with any wiring or plumbing that might be behind

the surface area. Installing on soft materials or in areas incapable of supporting the

speakers’ weight may cause personal injury or damage to the speaker.

·Make sure the speaker is properly secured to the ceiling/wall. Please use the proper

screws, bolts, or anchors. Failure to do so may cause the speaker to become

unsecured and cause potential damages/injuries.

·Damage to the woofer and tweeter may occur if the speaker is dropped or

hit-resulting in no sound or distorted sound.

·Never overdrive your speakers to the point of distortion and always reduce volume

prior to switching input sources.

·Use only approved and certified wiring in your installation, do not stretch or place

the wire in contact with sharp objects.

·Prior to removing cables ensure all power to your amplifier and other components is

turned off.

PREPARATION

The hardware equipment listed below is needed to install the speaker.

PACKING LIST

Ensure that you have received all parts according to the component checklist prior

to installation. If any parts are missing or faulty, contact your place of purchase for a

replacement.

Keyhole Saw/

Cutting Saw

Wire Stripper Phillips

Screwdriver

Pencil

Tape

Measuring

Stud Finder

(For Wood Stud Wall)

Safety

Goggles

Ladder

Speaker Grill Cutout

Template

User Manual

INSTALLATION

1.Cut the Speaker Hole

Use a stud finder to locate an area

that is free of obstructions or studs.

Position the cutout template where

you are installing the speaker. Trace

the template to mark out the speaker

location with a pencil. Drill a pilot hole

and cut all of the way around the

circular outline with a cutting saw.

CONNECTION

Ensure that the speaker is unplugged from the mains before making

any connections.

Parallel Connection of Multiple Speakers

For distributed line application, built-in 100V multi-tap transformer offers the ability to

daisy chain multiple number of speakers in parallel. The total number of speakers

multiplied by the tap value cannot exceed the output power of the amplifier. For

example, if you want to daisy chain 5 speakers in total using the 15W taps, you will

need an amplifier with at least 5x15W = 75W. A good rule of thumb is to select an

amplifier with 20% greater power; in this case, an amplifier that delivers about 100W.

2.Wire the Speaker

Pull the speaker wire out of the hole

which you have cut and connect it to

the speaker as shown.

3.Install the Speaker

Place the speaker into the ceiling and

tighten all the clamp screws with a

Philips screwdriver.

4.Attach the Grill

As several magnets are on the speaker

frame, attach the grill to the rim of the

speaker directly. Ensure the grill is

attached to the speaker securely to

keep the grill from falling.

Produkt Specifikationer

Mærke:	Audibax
Kategori:	Højttaler
Model:	CS6T

Har du brug for hjælp?

Hvis du har brug for hjælp til Audibax CS6T stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler Audibax Manualer

Audibax PR-52 A Manual

12 Juni 2025

Audibax Denver 12 Manual

5 Januar 2025

Audibax CM508L-BT Manual

5 Januar 2025

Audibax Freeport 212P Manual

5 Januar 2025

Audibax Drop 6 Manual

5 Januar 2025

Audibax Denver 6 Manual

5 Januar 2025

Audibax CM608L-BT Manual

5 Januar 2025

Audibax GA05-T Manual

5 Januar 2025

Audibax CM408-BT4 Manual

5 Januar 2025

Audibax GA08-T Manual

5 Januar 2025

Højttaler Manualer

Nyeste Højttaler Manualer

Greadio R-919 Manual

14 Juni 2025

J.W. SPEAKER 8700 Evolution J2 Manual

14 Juni 2025

SpringFlora HM11 Manual

14 Juni 2025

Fiodio F-130 Manual

14 Juni 2025

HEYSONG Bubble Manual

14 Juni 2025

ANCOBER ACB-001 Manual

14 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025

14 Juni 2025